Similar Questions

• What I need to install in another pc without LabView and wants use executable Vi

  Hi, everyone, please, help me

  I want to use another VI without LabVIEW PC executable, what I have to do to run the VI.exe?

  Thank you

  At a minimum, you will need to install the LabVIEW runtime engine.

  You may need to install more depending on what your program does.  Maybe the drivers DAQmx or the VISA run-time.

• Use VirtualBench API without LabVIEW. Example: Python, dll, etc.

  Hello

  I would like to know if there is a way to use the API VirtualBench without LabVIEW?

  As the use of python or something.

  Thank you

  We just released version 1.1 of VirtualBench that adds a C API and a bunch of other features, see http://forums.ni.com/t5/VirtualBench/Announcing-free-firmware-update-version-1-1-adds-SPI-and-I2C/td....  With whom you could use VirtualBench in your programming language of choice if you write the appropriate links.

• Save the data of the 6000 USB without Labview

  Hi all.

  I'm sure that this questions is buried somewhere, so I apologize if I'm repeating a question that has already been asked and addressed. If this is a redundant question, simply pointing me back post relavent will help.

  I have a 6000 USB. I configured and works very well in a test panel Max is possible to log data acquired at one any file without Labview signal Express, studio or lab windows/cvi measurment? In a similar note, being able to acquire and record data without another routine of programming such as .net or C++. Maybe there is a way to create a task and call it from an excel macro?

  I know that I dug my own grave by getting to the bottom of the similar USB DAQ. However, even with the USB-6000, there must be a way to connect the data being acquired without having to invest more in software development. Does not seek to do anything fancy like trigger or manipulation of data, I'm looking to record the voltages measured to drop and do post processing in Excel.

  Still, I'm sure that this (or at least a similar) question has been asked before. Any help would be appreciated.

  Thank you

  Ben

  I think that Signal Express, it is what you really want to use here.  It was designed for the acquisition of very high level, simple as.

  In MAX, you can configure the task to save a PDM file.  This enabled, you should be able to leave just Signal Express your task and then tell him to stop whenever you want and the data will be saved.

• Create Setup without labview

  Hello

  Is it possible to create an installer without LabVIEW? I'm supporting Windows 2000 to 7 and software versions of NEITHER varies with each OS, especially when dealing with Windows due to conflicts VISA oscilloscopes.

  The two main problems I have with the creation of installers with LabVIEW (Application Builder):

  1) Windows 2000 requires the framework produced prior to 2.8.0. It is therefore impossible for installers run on Windows 2000, requiring the installation of the product more recent than 2.8.0 which is basically each installation for Windows 7.

  (2) as far as I know, the software must be installed on a local computer first before you can create a Setup program. Then, you go to the section of additional installers creating a Setup program to add to the installation. The location path will point to the orignal CD drive or location it was installed from the local disk. I do not see why it needed. Why can the Installer be created directly from extracted files without it installed on the machine?

  Thank you

  Wow guys, thanks for the blatent insults two. If you have nothing nice to say don't say it at all.

  A little more explanation:

  Press and hold Windows 2000 in 2014, I agree, are heavy. However, you will need to make these oscilloscopes that are running Windows 2000 in 2014 still cost up to $8,000 to replace and the operating system cannot be upgraded. Why always cost so much? Because they are very useful tools. New and cost $ 20 000 to $30,000. I don't think that this effort is "los [ing] [the company's] ability to make a profit.

  For those of you who are interested in Moose displayed question here is my solution.

  I used SFX Builder (http://sourceforge.net/projects/s-zipsfxbuilder/) to group software NOR in a single executable file. Here are the steps:

  (1) download all necessary software OR

  (2) download SFX Builder

  (3) download 7 - zip (http://www.7-zip.org/)

  (1) extract all the software OR in a single folder and 7-zip can compress them into one archive .7z

  (2) open the SFX generator and adds the tab file from archive .7z

  (3) you can easily set the path of extraction anywhere on the computer, the temp (%temp%) is most useful

  (4) the tab tasks, click add/plus button and select program to run, and then enter the path where the extraction happened, here's an example

  (5) easy as pie!

  

• How can I create a new file interactively in LabVIEW 2011?

  I am trying to create a new binary file interactively in LabVIEW, but control of path only gives the opportunity to type the path name and the complete file (cumbersome for the user) or search for an existing file. I want to open a dialog box "New file", which will allow the user to navigate to the target folder, and then be able to enter the name of a nonexistent file to save the data of.

  The way I'm currently doing it is to create a TXT using Windows Explorer file "New text Document" pop up, then change the file extension for the new value... which is once again, very heavy.

  The only thing I've found online is that there used to be a "new File.VI" in an earlier version of LabVIEW apparently... but I can't seem to find it in 2011.

  You can create a new file using the Browse button.

  Your right click the file path control and check the settings in the menu "Options to browse?

• Problem with window painted and scrollbars when editing (LabVIEW 8.0.1)

  I'm under LabVIEW 8.0.1 in Windows XP SP3.  For my main VI, I came across a strange problem about 5 months ago.  The front window - both in edit mode and run mode - arrested repaint itself on the right side which is no longer visible when you scroll from top to bottom, but also visible overlapping Windows.  Coinciding with the repaint problem, both bars scroll search disabled grey arrows and no boxes in the bars that you can click and drag to scroll the window.  The scroll bars work still partially if you pass the mouse over it and roll the mouse wheel but does not work by clicking and dragging.

  The façade has a lot of controls and indicators, including containers of tab control and is greater in the horizontal directions and vertical so the two scroll bars must be active.  But I deleted everything in the Panel before and everything in the schema and the problem persists.  If the problem is not directly related to a control/led display.

  I saved the simple VI to this problem (using a line of large text and a high box rounded to test), and then created a new VI and copied the two elements at the new VI.  This new VI didn't paint it and the problem of the scroll bar.  The two screws are slightly different in the memory usage and the revision number (bad is review 1785 and the good is revision 3), but otherwise the two screws are identical.  I have attached two screws at this announcement.  When you first open the bad VI, you will see the scroll bars disabled while the good VI has active scroll bars.  To replicate the repaint problem, scroll the window up and down with your mouse wheel.  If it's good when you first open the VI, click on another window, then click on the window of VI and try again the mouse wheel.  This by clicking sur-loin-and-return always causes the problem of repaint for me.  I tried the screw on two different computers, both running Windows XP SP3 and LabVIEW 8.0.1 with identical results.

  Here's what I discovered simple troubleshooting with the screws:

  always off scroll bars

  * repaint the problem in the main window for larger then 680 pixels of window widths

  * repaint the problem in the menu bar of the main window for widths of more than 646 pixels

  * entire window becomes disabled than 1348 pixels window width

  * can paint window minimize and restore, but only repaints only once

  * scrollbar boxes sometimes flicker in the display, but then disappear

  * Scroll left and right hovering mouse over the bar and horizontal scroll by using the mouse wheel

  I found something similar on this forum (thread: problem with refresh of façade)-it could be linked to the CAR on the Panel being offset internally.  I don't have access to LabVIEW 8.5 or later and do not plan to upgrade - I have not tried the trial version, as this user has done.  I could try to copy and paste my set of the block for a new VI diagram but the VI is so important I'm afraid something would break, plus I don't want to do it again in a few months.  The problem seemed to occur after a certain number of stops (or revision number).  I save copies of backup often and when the problem first happened, I was able to go to a previous version, make the missing changes and save it without any problem, but this only delayed the problem and he came later.  It is therefore perhaps the revision number.  It seems not related to a change or a particular addition in the front panel and the graph.

  The attached picture shows the repaint problems and scroll bar in bad VI.

  This raises a question I have - if this problem is a bug has been fixed in 8.5 and later, is it possible to apply bug fixes for older versions?  Or what I need to pay for an update fix these bugs?

  Seems that something got corrupted with this VI. Things to copy on a cool VI and things should be OK.

  See also this recent report of a similar problem.

• While on a page web, using one of several browsers, it will take off and scroll down without any input from me. Seems to be intermittent but annoying. All solutions?

  While on a page web, using one of several browsers, it will take off and scroll down without any input from me. Seems to be intermittent but annoying. All solutions?

  This could be a case of interference.   Read this document about it.   Think about the suggestion of new electonic or other nearby wireless devices.   I recently read the someone pen wacom being the culprit.

  Potential sources of interference Wi - Fi and Bluetooth - Apple Support

• I downloaded the last Adobe Flash - it is said to be successful but will not work. What he says "Manage plugins but the plugin says it is enabled, but it will not work." I have tried disabling and then enabling - without success.

  I downloaded the last Adobe Flash - it is said to be successful but will not work. What he says "Manage plugins but the plugin says it is enabled, but it will not work." I have tried disabling and then enabling - without success. Help, please!

  There are two different versions of Flash. ActiveX for IE version and the version of the Plugin for other browsers. Have you installed the correct version? This forum software is not thing that Flash is installed for Firefox or the Plugin is disabled.

  1. download the file of configuration Flash from here:
  
  Adobe Flash - Plugin version.
  
  Save it to your desktop.

  2. close Firefox using file > exit
  
  Then check the Task Manager > processes tab to make sure that firefox.exe is closed.
  
  {XP: Ctrl + Alt + Delete, Vista: Shift + Ctrl + ESC process tab =}

  3. then run the Flash configuration from your desktop file.

  4. run Firefox and test your installation here: https://www.adobe.com/software/flash/about/

  • On Vista and Windows 7, you may need to run the installer of plugin as administrator by starting the installation program via the context menu if you do not get a UAC prompt for permission to continue (that is to say that nothing seems to be happening).

  See this:
  
  http://vistasupport.MVPs.org/run_as_administrator.htm

• I missed the prompt to update my notes. My software is up to date, but there is no option to update notes. How can I get this opportunity again? I want to sketch options and make interactive lists.

  I missed the prompt to update my notes. My software is up to date, but there is no option to update notes. How can I get this opportunity again? I want to sketch options and make interactive lists.

  Open the Notes app and look near the upper left corner to see if the upgrade option is there.

• Satellite A100 - 294 PSAA8E: black and white TV without sound picture

  Dear all,
  When I select the TV mode, my TV shows black and white color without noise.
  WHY?

  I have:
  Satellite A100-294
  Part number: PSAA8E-02T014GR

  I check the cable to use it in my CAM.

  Hello

  I assume that you have chosen the wrong settings of PAL/NTSC.

  Please check if you are using the right settings that correspond with your country where you live.

• my computer screen goes off for a few seconds and the lights without turning off the unit. This has happened several times, regardless of the period in which stays on.

  My computer operating system Mac Pro OS X EL Capitan 10.10.3, ink 13"early 2015 screen off for a few seconds and back on without turning off the unit.

  This has happened several times, regardless of the period in which stays on.

  Don't know what is happening with your publication details.  You posted in space of the Macbook Pro forum & even your profile indicates: ' MacBook Pro (retina, 13-inch, early 2015), OS X Yosemite (10.10.3)..

  Your post indicates you are using a Mac Pro, which is a desktop computer and with the help of El Capitan who is 10.11.2 not 10.10.3 which is Yosemite - 'my computer operating system Mac Pro OS X EL Capitan 10.10.3.

  

• Help! My iPod Classic 120 G froze. Pale = 'Media-In' and display the screen = "OK to disconnect with a bar in the middle." Tried the reset procedure, press the "Menu and Center." Without success. Any ideas?

  Help! My iPod Classic 120 G froze. Pale = 'Media-In' and display the screen = "OK to disconnect with a bar in the middle." Tried the reset procedure, press the "Menu and Center." Without success. Any ideas?

  See Re: corrupted iPod classic. If she does not really have a reset set it aside and let the battery completely discharge. It should reset itself when you load again.

  TT2

• Impossible to find the field read and write VI in labview 2009

  where is the field point to read and write VI in labview 2009

  According to the version of LV, BT pallets can be sensitive to the context. Try to create a project and add a fieldpoint target to the project.  Right-click on the target of FP in your project and select new > vi.  Now FP functions should appear

• Opening Word, Excel and PowerPoint files in LabVIEW with digital signature of files

  Hello

  I try to open Word, Excel and PowerPoint documents in LabVIEW (or were then converted into a format that can be opened). After the opening, to fill out checklists can insert a digital signature preset (possibly through an authorisation of user name and password) and save the file while preventing further edit or print a pdf of this report.

  I have a good experience with LabVIEW, but not in this kind of a system.

  I appreciate if someone can point me in the direction to start.

  Thank you very much

  Al

  Regarding (1): there is no ActiveX control to view the Microsoft Word/Excel/PowerPoint files. If you want to display these on a front of LabVIEW, so the simplest solution is to use a web browser on the front panel control. This will allow you to provide the path to the file in the URL of the web browser control navigation and the file will be embedded in the browser control. It would be no different than the consultation within Internet Explorer.

  Regarding (2): assuming that you view the document on the front panel, this looks like the basis of LabVIEW programming, so I don't know what you're asking for here, or that you are having problems with.

  With regard to the (3): I must admit that I'm not quite clear on what will be signed. It also seems that the signing and printing of PDF are two distinct objectives here.