No Audio or USB ports with Port Replicator 3 and Portege R600

Similar Questions

• USB Port Replicator II and IEEE1284 - Windows XP

  I have a replicador (Px1098e-1prp) port and it is impossible to operate LPT (IEEE1284) however in Windows 98 works perfectly. I have a M30-801 and I also proved in several computers, and it won t work with Windows XP. How can I do works?

  Thank you!

  Hello

  The only thing I can tell you is that you need to check the user's manual and it is described how you set up the printer in Windows XP Home edition. You can find it on page 24 (English).

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• Dynadock - USB Port Replicator does not recognize any USB keyboard

  Hi can any body help?

  I have a Satalite pro L300-154 with a Dynadock - Replicator to USB Port, but it will not recognize any usb keyboard.

  Have you checked if the laptop would recognize the external USB keyboard connected directly to the computer laptop s USB port?

  Please check this!

• Problems with an external monitor with the Port Replicator III and M100

  Hey all.

  I just returned from a trip where I took my laptop. Plugged into the Port Replicator port, started and everything was fine. Then after an hour or two, the monitor stopped receiving a signal. I repositioned the laptop and everything was good again. He then loses signal once again, and I was not able to get a signal via the port replicator since.

  The monitor works fine through the hole at the rear of the M100.

  I checked the pins on the Port Replicator port and portable, none folded and tried to clean any dust etc. Still no signal to the monitor.

  Someone has ideas of how to do to solve this problem?

  Jamo

  Hello

  The Toshiba 3 mobile extension is responsible for the good condition of the duplicator 3 market. Try to reinstall this utility and also check the page of the Toshiba driver for updates.

• Express Port Replicator II and Tecra A10 - 12Z - only the power and LAN

  Since my Toshiba T3600CT I received with docking station, I discovered that I have a docking station. In the meantime, I had a small Sony who had no docking station, for which I got one of the first USB docking station and since then I've seen always to get laptops with docking station.

  But this time something went really wrong, the Toshiba Express Port Replicator II PA3680E-2PRP provides only power and LAN. There is no power in the USB ports, so no serial port or the sound, and DVI and VGA are also disabled.

  All these ports work fine on the Tecra A10, but not on the docking station.

  Of course, it is nice to have the power and LAN, but not when I expected too much of everything.
  So I was wondering if anyone has had a similar problem, it is like upgrading the BIOS for me who have not installed all the necessary software, or is it a fuse or something I could fix myself or is it a faulty docking that shouldn't have left the factory?

  Hello

  What's your Tecra pre-installed with original recovery image?

  When the laptop is preinstalled with recovery image simply connect compatible laptop Toshiba docking station and all the devices connected to the docking station will be recognized correctly and all available ports should work fine.
  Is that a Port Replicator basically "replica" ports on the laptop.

  On this virtual path, we cannot say that this port is 100% OK. What can you say about it? you bought is used a?

• Advanced Port Replicator III and Tecra M5 - compatibility issue

  Hi all

  Had a brief search, but could not find a similar position.

  Is the Advanced Port Replicator III PA3314E-1PRP compatible with a laptop Tecra M5?

  Thanks in advance and amicably.

  James

  Yes, it is compatible, I can confirm this info above
  If you wish, you can consult the Web of Toshiba Europe site Options & accessories.
  You will find this info useful

• want to 810-430qe CTO: 810-430qe CTO... of the usb ports 3.0 and 2.0 ports, which are which?

  computers HP do not seem to come with a simple explanation of usb port scheme and since there are a dozen of them, I would like to know precisely which are which?    Help, please...

  Hello @mikesoares,

  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  I read your post on USB ports and wanted to help you!

  USB 2.0 ports are black while the USB 3.0 ports are blue.  Please see the picture below, which shows the ports at the back of your desktop:

  Figure: Kaili2 back i/o ports

• Windows Vista - why my usb ports stopped working, and how do I fix them?

  My 3 usb ports worked very well, but a few days ago they just stop working.  I updated the drivers even though my drivers were already later.  I even tried to update the drivers.  Nothing seems to work.  Can you help me?

  Hi WillisPop,

  ·         Since when are you facing this problem?

  ·         You did it last changes before the show?

  Use Device Manager to disable and re-enable all the USB controllers

  This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

  To disable and re-enable the USB controllers, follow these steps:

  1. click on Start, type Device Manager in the start search box and press ENTER.

  2. expand Universal Serial Bus controllers.

  Note: you may scroll through the list to find this point.

  3. right click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

  4. repeat the above steps for each controller USB is listed under Bus USB controllers.

  5 restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  6. check the USB device to see if it works.

  You can also check out the article below for more information:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-in/Windows-Vista/tips-for-solving-problems-with-USB-devices

• USB ports suddenly freeze and stops working for 10 sec after power off or powered speakers

  Original title: Usb Ports stop working for 10secs after power off or powered speakers!

  Hello

  I have no why, but my usb ports suddenly hangs for 10secs when my speakers turned on or off the power in case of operation of pc... And I have a usb mouse usb wireless keyboard and... with this problem that I can not work properly... and some times my mouse work in early upward and then I should use my keyboard to restart the pc... Then it works very well! Help me please. !

  Hi Thierry,.

  This issue does not appear with Windows that even after you perform a clean installation. So for me, it looks like a material damage. I would recommenmd get you in touch with the manufacturer of your computer and to do the repair.

  Do not hesitate to contact if you have problems with Windows in the future.

• WiFi radio adapter off, the USB ports does not and the Bluetooth adapter is no longer visible... Please help!

  I had my laptop Dell Vostro repaired under insurance in January 2013 after a spill of liquid.  HAAC Ltd. has replaced most of the laptop - but the return, the SD card did not work.  This seems to be due to the engineer he connects not properly and the company recommended it and returned it to me again.  A couple of months, I found my USB was temperamental - so is my built in Bluetooth adapter.   Last month - the wifi does not work for most of the time either so I have to connect to my router by wire.

  This could be a problem in windows 7 - all my problems seem to be related to network adapters.  If it's a hardware problem - does anyone know if it could be another loose connection?  HAAC Ltd. only give a 3 month warranty on parts that seems just a little.  But if this anomaly is due to the production of poor quality - that is not properly connect the laptop then I'll go back their again if they are responsible.

  By the way – there's a switch wifi on the front of the laptop - but is not currently be recognized.

  If anyone has settings that I could check that can help - especially if some inhibit the use of wifi.

  Thank you very much

  Hello

  Your wifi switch not recognized is probably a hardware problem. The rest could be a hardware or software problem.

  Method 1:

  Lets start by doing a reset to coercive. Follow these steps:

  1. Unplug the notebook (remove power cord), then remove the battery.
  2. Disconnect all USB devices and the connections between the USB ports.
  3. Let the laptop only for several minutes.
  4. Then plug the power cord without connecting the USB devices. Then replace the battery.
  5. Plug each device in turn, allowing them to load the drivers of devices one at a time (plug in the appliance and wait its loading all its drivers before installing the next USB).

  The computer recognizes the USB ports? All of them or none of them?

  Method 2:

  Open Control Panel, Manager of design. Click the view tab, and then click Show all devices. From there, you can remove all instances of USB devices and restart the computer to see if the problem resolves. Repeat this procedure with the wireless adapter (uninstall and reinstall, ensuring that there is only one instance of the wireless adapter).

  Method 3:

  Create a new user account by following the instructions in this article:   http://windows.microsoft.com/en-US/Windows7/Create-a-user-account . Does this solve the problem?  If the problem is resolved in a new user account, this means that the old user profile is damaged. Here is the link to repair a damaged user account: http://windows.microsoft.com/en-us/windows7/Fix-a-corrupted-user-profile.

  Try these methods and post your results here. I'll be here waiting for the results!

  Kind regards

  BearPup

• Lenovo Enhanced USB Port Replicator - FRU 43R8811

  
  
  

• Port replicator 2504 and w530

  Hi all

  I would check if the 2504 is compatible with the W530?
  I realize it will miss the USB3.0 features, but this isn't a problem.

  Welcome to the Forum!

  Advanced cradle 2504 is not compatible with the W530. You will need a Mini Series 3 with USB 3.0, or Mini Dock more Series 3 with USB 3.0. Click here for numbers of exact model that you can use with your system: http://support.lenovo.com/en_US/product-and-parts/detail.page?&DocID=PD024298

• Tecra A8: Problem with the USB printer connected to the Port Replicator III

  Hi all

  I have a problem with my Tecra A8, year Advanced Port Replicator III and a USB printer. With the printer connected to a USB port on the Port Replicator, I have to wait 2 minutes for printing to start. When it is connected directly to a USB port on the laptop and the laptop disconnected from the Port, printing starts immediately. I have the latest drivers from the Isensys of Canon LBP 2900 installed and Windows Vista professional as the operating system.

  I called the technical support of my country, but her is not recorded similar problems.

  A person with similar problem? Some help would be very appreciated.

  Thanks in advance.

  Hello

  Seems like a strange question... Already done the standard procedure in the event of such errors? :)

  The standard procedure is somehow similar to the following:

  -Update your BIOS
  -Update all the drivers for your machine
  -Update your printer drivers
  -Update your operating system

  If all else fails, then try an another Portrep if available, maybe you need to contact your dealer for an another portrep for the test.

  Something like this should be your way. And then you sucessfully made a TROUBLESHOOTIN´ ;)

  I'd be happy to hear feedback from you on your situation...

  Welcome them

• Tecra S5 - slow ethernet with USB 2.0 Port Replicator

  Hello

  I have a Tecra S5 with USB 2.0 Port replicator II. I have 3 ethernet connections all together on my PC: LAN on motherboard, WiFi and the other on the USB port replicator.

  At home, I use WiFi for internet connection and USB to Ethernet to a wired connection to devices with built-in web server.

  My problem is that when the WiFi and USB to Etherenet is active the internet and the connection to the web server works but vey slow.
  If I turn off the WiFi and connect to the web server works properly.
  If I disable USB for Ethernet internet connection works correctly.

  Anyone has same problem and suggestion how to solve?
  I downloaded the latest drivers from the Toshiba support page.
  My OS is XPSP2.

  Concerning
  jballa

  Hello!

  It looks like a network configuration problem. Check the network addresses and configuration in command line with the command ipconfig/all.

  Try using static IP addresses. I think that the DHCP server takes a long time to go send an IP address to each laptop.

  Good bye