No bar of tasks or cursor after replacement of the HD and install Win 7

After a hard drive failure, I replaced the drive and installed Windows 7.

After that Windows Update Setup, I don't have a taskbar, start button or the cursor of the mouse.

I have only access to the desktop in safe mode. Any help is appreciated.

Rob

What exactly was the disc that you used to install Windows 7?

Have you tried to format the drive and reinstall Windows 7?

Tags: Windows

Similar Questions

  • All icons are shaded and wavy after installation of the patch and restart (win xp sp3). How can I fix it?

    After you have installed the latest patches, all icons are shaded with vertical lines undulate on them.  Computers desktop and in Windows Explorer.  Application windows appear clear, but icnos in their midst are the same way.  What should I do to fix this anomaly?

    -J' tried the obvious desktop refresh. No change.
    -J' rebooted in safe mode, and then back to standard mode. No change.

    What else can I try?

    Hi JimGoode,

    Unfortunately, the screenshots are not available in the post.

    Given that the question does not appear in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.

    I suggest that you put the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See the link below to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    (a) click Start, type msconfig in the search box and press ENTER.

    (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

    (c) under the general tab, click the Normal startup option, and then click OK.

    (d) when you are prompted to restart the computer, click on restart.

    If the previous step fails, then use SkyDrive download screenshots of icons.

    Use SkyDrive download collected files and after shot/screenshot.

    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65/

  • Real window7 after replacement of the processor and motherboard

    I bought authentic window7 and installed in my computer. Later, the card mother and processor changed because of problem and installed windows7 CD I own.  Now, it shows that the windows7 is not authentic. Please help me.

    Tibo Mathai.

    Hi Samuel,.

    You get an error with the message?

    Genuine Windows is a recurring process that checks your product key to ensure that it is not blocked or used on a different material that you were using when you activated Windows. If the product key is not genuine, it is likely that the product key is used on another computer or is a counterfeit.

    Real control, or the validation is done when your computer tries to download optional updates from Microsoft. For example, when your computer downloads updates, Windows checks to see if your product key is valid. If this is the case, Windows on your computer is genuine, and you are eligible to receive updates from Microsoft. If this is not the case, your computer is running non-genuine Windows.

    Take a look at this Microsoft KB article if you get the error code 0 x 80070005.

    Windows 7 displays "Windows is not genuine".

    You can also consult the suggestions provided by Keith from the link.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-is-showing-as-not-genuine/cbd43297-0e4d-458C-8487-9168c4cd668d

    Visit this link for your reference:

    http://Windows.Microsoft.com/en-in/Windows7/activate-Windows-7-on-this-computer

    Answer if you need help with the issue and we will be happy to help you.

  • Laptop screen stays black with the mouse cursor only after that comes the HP and Windows logo

    Hi all

    No, my laptop model is HP Pavilion dv6 1337tx. My OS is Windows 7 Home Premium 32 bit. So, today, I shut my laptop down by force by pressing the power button because it did not at this time. Then the next time I turned it the wrong problem started. Whenever I'm on the HP logo sometimes and then the Windows logo comes also. But then the screen stays black and the mouse cursor appears. So, what can be the cause of this problem? I also tried to open with 'safe mode' and 'safe mode with command prompt', but they did not help either.

    Note - I tried the method of discharge after taking off the battery and holding down the power button. He could not help. All LEDS are working properly. I have no extra monitor, so I can't check the display elsewhere. Also, I ran the memory test which shows that everything is fine. Please suggest what I can do now as I can not enter the laptop now. What can be the reason?

    Black screen with blinking cursor:

  • I tried to reinstall yosemite OX since yesterday after I wipe the drive and it froze.  It is said bark 2 hours and 7 minutes since last night.  What can I do?

    I tried to reinstall yosemite OX since yesterday after I wipe the drive and it froze.  It is said about '2 hours and 7 minutes' since last night.  What can I do?

    Try to turn off the computer with the power switch, and then restart.

  • I'm trying to export contacts as vcards icloud.  However, after that select the contacts and click on "Export as vcards" nothing happens.  Why?

    I'm trying to export contacts as vcards icloud.  However, after that select the contacts and click on "Export as vcards" nothing happens.  Why?  I tried this using edge and chrome and I run Windows 10

    I just tried with edge on Windows 10. I selected all the contacts, and then click Export, as vCards and nothing happen. Clicked on it again, still nothing. After 4 or 5 click on about 10 to 15 seconds he finally uploaded to the file Edge uses for downloads. I saw it happen before you go to a Mac using the Safari browser, but only 2 clicks were necessary.

  • I can't find application webcam on my PC after formattting, but the hardware and the software is in the Device Manager

    I can't find application webcam on my PC after formattting, but the hardware and the software is in the Device Manager

    I can't find application webcam on my PC after formattting, but the hardware and the software is in the Device Manager

    You need to reinstall the driver of web cam and related demand.

  • Initially, I downloaded the application and was able to access all my photos by album, photostream, fb, etc.. Now, it will not go all. After you remove the application and try to download it, it says that I have to pay for it (yet) any help would be

    Initially, I downloaded the application and was able to access all my photos by album, photostream, fb, etc.. Now, it will not go all. After you remove the application and try to download it, it says that I have to pay for it (yet) any help would be appreciated.

    Sounds like a question of verification on any market that you have bought PS Touch. Have you tried contacting Google and Apple to see what they say?

  • replace only the first and the second comma by TAB in the apex using using jquery

    All,

    I'm generating models of string in the text box in my apex as page == > 23232,445454, «454545,7878,988978, 3r3e»
    and I want to replace only the first and the second comma with TABS so I get like == > 23232 445454 «454545,7878,988978, 3r3e»

    It should run with the jquery code when I click my button?

    any help on this please?

    Thank you.

    How does this update function:

    function replaceUpToN(original, search, replaceWith, maxOccurence){
    
        var NEW_LINE = '\n';
    
        var lines = original.split(NEW_LINE);
    
        $.each(lines, function(index, value){
            var idx = 0;
            lines[index] = value.replace(search, function(match, pos, original){
                idx++;
                return idx <= maxOccurence ? replaceWith : match;
            });
    
        });
    
        return lines.join(NEW_LINE);
    
    }
    
  • Satellite P755 - 11G: Win 7 64 bit - cannot activate BT after replacement of the module

    Hello

    On my laptop Satellite P755, I had to replace the Wifi/Bluetooth PCI Express Mini card because the original Atheros was broken and was no longer working.

    So I decided to buy a new Intel® Wireless-Dualband-AC 7260 card to replace.
    Has successfully replaced by itself.
    WiFi now works again.

    Now, I'm dealing to get BT running. With the old Atheros card I could activate BT by pressing FN + F8 and choose Bluetooth from the menu of flashcard on top of the screen.

    After the replacement of the F8 full option in flash cards had disappeared.
    I managed to solve the problem for the WiFi by adding the ID of the new material of the card Intel (PCI VEN_8086 & DEV_08B1 & SUBSYS_40708086) in the registry in the following locations:

    HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\ConfigFree--> InternalDevice176
    Hotkey HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\Wireless--> DevID_SupportRL175
    HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\WirelessAPL\BT WLANDP--> DevID_SupportRL176
    HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\WirelessDevice ID--> DevID_SupportRL176

    Now FN + F8 works very well for the WiFi, flash cards menu appeared again.
    But there is still no option to activate Bluetooth.

    Addition of the BT hardware in the registry (same locations as the WiFI) ID does not help.
    I can't get the point how the flash cards software manages to activate the bluetooth normally.

    Does anyone have an idea what it takes to get the Bluetooth in the menu flash cards?

    My system:
    Toshiba P755 - 11G
    Windows 7 64 bit

    See you soon,.
    Alex

    Hello

    You said that the original WLan module was to Atheros.
    As far as I know the module Atheros WLan additional needs for the installation of the filter for the Atheros BT driver package in order to use and activate Bluetooth.

    In the case of modules WLan Intel such package of filter is not necessary.

    I guess the Atheros BT filter driver package is always installed on this laptop and I think this might be the reason why the BT can not be activated properly.

    However, I recommend you to uninstall the filter BT mentioned driver package as well as Toshiba BT stack, driver Atheros WLan and the Toshiba value added package, and the Flash Cards Support utility. Clean the system using the CCleaner tool.

    Then install the Intel driver that would control the new Intel WLan card.
    Install the Toshiba BT stack and restart the device. Now follow with the installation of the Toshiba added value package and the Flash Cards Support utility. Reboot once again and check if you can use FN + F8 to activate WiFi and BT

  • Help: Laserjet M1536dnf does not scan after replacement of the router

    Hello

    I have a LJ1536 that has worked well until I had to replace my network router after it failed. Now, I can print on both computers I have in the same local network, copy locally in the printer, but will not scan. The printer is connected to the router via an access point configured as client and connected to the printer wireless. After the failure this AP router had to be reconfigured to the new router.

    I tried scanning disabling firewall and anti-virus, delete and reinstall all software using the latest version on the web and nothing. FX HP Toolbox works very well. HP Print and doctor Scan did not help. WIA service is Started (auto mode) on the computers.

    I get the message on the two computers during an attempt of analysis:

    Inaccessible scanner

    Scanner communication cannot be established. If make sure that your product is powered, check the connection and make sure that your network is working properly. If these conditions are correct, restart the product and try to scan the image.

    If you are running a software firewall, it can block scan communication. Please visit www.hp.com/go/wirelessprinting for help to configure your firewall.

    Configuration:

    Windows 7 64-bit on both computers

    LF1536 FW dated 14/01/2013

    Any suggestion?

    Hi Jhenrichs,

    Thanks for the reply.  If the AP was configured to router manufacturer's specifications, it should allow a communication as it did with the previous configuration.  Check the below settings that may fix the problem.

    The AP settings:

    1. make sure that port forwarding is disabled

    2 disable DHCP (this should only be enabled on real router), it can be set to automatic or static, but disable DHCP on the access point

    I hope this helps!

  • G10 Flash problem after replacement of the lens - ideas?


    Hi, I'm guessing that you don't have the service software, update of tables, box of collimator etc to recalibrate the system of lenses?

    When the camera takes pictures in what image?

    I doubt you have 2 bad lenses.

    You have the service manual? Platinum flash connects usually to DC power immediately the battery box, look in this area for a problem with a connector, you can have inverted one on both devices? I worked on a few models, G5 and the S5, but never on the Assembly of lenses because of all the special tools and software required. I was able to locate the service manuals for the ones I worked on the first. If you do not try and find maintenance manual.

    So my assumptions are you making the same mistake with the connectors on the PCB flash on or near the battery on both devices box or systems of lenses must be recalibrated is why you have this symptom "hunting".

    Also as a thought after you have the AC adapter, if so try using them and see if the flash works. If it works with that then your problem is most certainly in or around the battery box/cards PCB.

    Let me know what you find.

    John

  • Product key recovery Windows 8.1 AFTER replacement of the operating system

    Hello

    I was wondering if there is any way out of this pickle.

    I had problems with my pc (mainly the printer spooler errors) of a virus so I decided to do a system restore. Only problem was that I had the pc built for me and the person has used a downloaded Windows 8.1 version (no cd). When I went to restore the operating system he said I was "missing data". As I had no cd to I found a so-called work around where you use the missing data from one version of windows business to fill the gaps and it should allow me to restore the version I had (8.1 regular).

    Well low and behold, I load my windows and it is has been replaced by this...

    So I tried to reinstall Windows 8.1 using the ISO and the extraction of the key with Magic Jellybean, but, of course, the key had been crushed as well with this useless key.

    I called Microsoft to see if they could recover my OLD key that has written more because I was signing on my account when I logged in while I had my version 8.1 ordinary and download of updates. The people at the other end doesn't seem to understand what I was talking and kept transfer me different places when they are confused as to what I was asking (the language barrier I guess).

    ALL I NEED IS MY OLD RETURN KEY! If not hidden on my computer somewhere so how to get Microsoft to please look into this also. I even signed up for Windows 10 deployment on my 8.1 original.

    Thanks in advance

    Hello

    I was wondering if there is any way out of this pickle.

    I had problems with my pc (mainly the printer spooler errors) of a virus so I decided to do a system restore. Only problem was that I had the pc built for me and the person has used a downloaded Windows 8.1 version (no cd). When I went to restore the operating system he said I was "missing data". As I had no cd to I found a so-called work around where you use the missing data from one version of windows business to fill the gaps and it should allow me to restore the version I had (8.1 regular).

    Well low and behold, I load my windows and it is has been replaced by this...

    So I tried to reinstall Windows 8.1 using the ISO and the extraction of the key with Magic Jellybean, but, of course, the key had been crushed as well with this useless key.

    I called Microsoft to see if they could recover my OLD key that has written more because I was signing on my account when I logged in while I had my version 8.1 ordinary and download of updates. The people at the other end doesn't seem to understand what I was talking and kept transfer me different places when they are confused as to what I was asking (the language barrier I guess).

    ALL I NEED IS MY OLD RETURN KEY! If not hidden on my computer somewhere so how to get Microsoft to please look into this also. I even signed up for Windows 10 deployment on my 8.1 original.

    Thanks in advance

    Hello

    Ask the person who has built your computer and installed Windows 8.1 where they have bought and what they were doing with the product key.

    See you soon.

  • Signature LUN after replacement of the RAID controller

    I have the following scenario:

    I had a Cisco UCS server with an LSI controller. I needed to replace the controller to another, the same form, different model.

    I've done the replacement physical, powered on the server. ESXi starts fine, but no data store appears. Data warehouses are on the local hard drive. There is no remote storage.

    When I try to add the data store, I had 2 options of mainly:

    -Keep the existing signature

    -A new signature assing.

    I'm sure both will work, and I'd go with the first.

    However, I would like to know what impact the selection of one of these options. Similar cases, I will, will that be the best since I'm on a new material for RAID controller?

    Or would it not matter at all if I keep the same signature?

    I have beenr of reading on these 2 options, and for local storage, they do not seem to make any difference, but would like to know any other thoughts.

    I kinda fear Award for a new signature.

    Thank you.

    Due to the replacement of the controller, the ESXi host now recognizes the LUN as a snapshot LUN, it contains a signature known, but it is presented to another controller. Given that you can ensure that the logic unit number is unique, I don't see a requirement for resignaturing it.

    André

  • Menu remains visible after you make the selection, and does not show Popupscreen

    Hey. Unable to get a (a gaugefield) on a Popupscreen progress bar to show. It is called from a menu. The user clicks a menu item, and a method is called. The method among other pushes a Popupscreen containing a Gaugefield on display battery-code below. Then, he starts a thread which downloads an image and using join() to wait for it complete (long story). Then, in the thread of events, it appears the Popupscreen.

    The menu does not disappear when you click on it in the Simulator (JDE 4.7, the Bold 9700 sim), but the download happens. Once the download is complete, the menu disappears, the Popupscreen is shown and he tried to pop() Popupscreen, causing an IllegalArgumentException.

    I tried to split the method into two methods, the download happened in the 2nd method, because I read the forum search that the UIEngine don't update the display until the method finishes (it runs in the event thread). But it made no difference...

    How can I get this menu to disappear immediately and the push (popup) to work?

    See you soon!

    Justin.

                            progressbar = new GaugeField("", 0, 100, 50, GaugeField.NO_TEXT);
                            progress = new PopupScreen(new FlowFieldManager()) { protected void OnDisplay() { super.onDisplay(); /*cancelButton.setFocus();*/  }  };
                            globalTiles.pushScreen(progress);
    
                            progress.add(new LabelField("Downloading (rest of) picture ..."));
                            progress.add(progressbar);
                            progress.setFocus();
    
                            if (!threadbg.isAlive()) {
                                       threadbg = new ThreadForBgDownload();
                                       threadbg.start();
                            }
                            else {
                                       // Show the progress bar, mostly complete (it is running and was in the bg). Game will start after last bit done
                            }
    
                            threadbg.join(); // Wait for download thread to complete and 'die'
    
                            globalTiles.popScreen(progress);
    

    Rule #1: all display updates should occur on the thread event or synchronized on the lock of the event.

    Rule #2: the thread of events (or now the lock of the event) should never be blocked by lengthy operations.

    The scenario you sketched out is usually handled like this: menu item run() method don't whatever immediate user interface updates are necessary and starts a worker thread. It does not wait until the thread ends before returning. (If so, updates the user interface include pushing a "Please wait" or progress pop up). The worker, at the same time, begins to do its stuff. When it's time to update the user interface (either because the task is completed or to view progress) the worker thread usually called invokeLater (Runnable) (a method in the Application class) where the executable run() method updates the user interface. If the worker thread must receive user input in his work, he can use invokeAndWait (Runnable), where the executable not all interactions of the user and stores the user entry somewhere so that the worker thread can grab after invokeAndWait() returns.

    Although the synchronization on event lock works perfectly well, it is more common for some reason any to invoke a Runnable, perhaps because the latter clearly encapsulates in a separate object the work to be done on the event thread.

    The above policy is the basis of the excellent Peter Strange example I linked to before.

Maybe you are looking for