No connection to the local network, cannot connect - Satellite M35-S163

Similar Questions

• cannot connect to the local network using windows 7

  Recently bought a HP Pavilion laptop (AMD Athlon II P320 Dual - Core) ((G62 - 208CA)). Having a problem connecting to the local network. I have flashing lights on the lan (orange and white) connector.

  Using the ipconfig command, I get an IP address, subnet mask and gateway by default however messages below will appear:

  Tunnel adapter isatap. <578608BD-22EF-4A01-90ED-D709CB81D027>:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel connection to the Local network adapter * 9:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. :

  State media: media disconnected

  The connection-specific DNS suffix. :

  TEREDO TUNNELING Pseudo-Interface tunnel adapter:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. our field: *

  State media: media disconnected

  The connection-specific DNS suffix. :

  I tried to turn off the firewall and connect without success

  My network card is a Realtek PCIe FE Family Controller and confirmed that the drivers are up to date

  Any help would be appreciated

  Thank you

  Well Yes! So it was an older version of the bonjour service... thank you Adobe.

  You can find the latest version here:

  http://support.Apple.com/kb/DL999

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

• HP OfficeJet Pro 8600: HP OfficeJet Pro 8600, connected to the local network but does not print a printer on the same LAN

  HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.

  Work tried fixing it but all attempts fail.

  Firewall disabled.

  Printer recognizes the router's LAN.

  Was also pointed out that the port does not communicate, can not remove it; Cannot add another...

  Printer does not print.

  How can I fix?

  Hi @AnnisMonadjem,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  When you say 'LAN', are you referring to the network or you try to share the printer on the network?

  How is the printer connected? (Ethernet/WiFi)

  If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  HP has several Officejet Pro 8600 series.

  What is the name and the product number of your printer? How can I find my model number or product number?

  • Update the firmware of the printer.
  • Don't hide the SSID (network name).
  • What type of encryption are you helping? HP recommends WPA and WPA2.
  • You have a double router broadband? Make sure that the two groups were not the same network name.

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  To assign the static IP address, use the following steps as a guide.

  • Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.
  • Restart the router, the printer and the computer.
  • Test printing and scanning.

  If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2

  • Try printing and scanning.

  In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).

  Continue on, if the problem persists.

  Important!   Delete the temporary files and folders by using the disk cleanup utility

  1. Open the disk cleanup utility:

• lost internet, tcp/ip is not binding to connect to the local network.

  cannot access internet on network adpt since Saturday, January 22, 10.  said Network Diagnostics does not bind ip to connect to the LAN adpt.  When I go to L A Conn ipv4and6 properties are both checked.  I uninstalled and reinstalled the ptba and ip lan protocols.  ipconfig/all shows no IP information.  I have reset the battery.  network of diag stills said make sure that tcp/ip4 and ip6/tcp are selected in the config to connect to the local network [but they].  TIA

  try to uninstall and reinstall the network drivers and check if that helps

  For more information, you can refer to:
  http://www.madboa.com/geek/SOHO-bind/
  http://TechNet.Microsoft.com/en-us/library/cc977313.aspx

• Network Diagnostics says "connection to the local network 2 has no valid ip address.

  Dear Sir/Madam,

  I use the computer dell laptop windows 7 Home premium 64-bit. Usually, I connect my laptop to the internet through wifi modem. It connects automatically to him and there is no problem. But suddenly, the connection is not showing this wifi but signal showing other signals. I plugged the cable, but not showing also no internet access, then I used the diagnosis then he showed "connection to the local network 2 has no valid ip address" other devices such as my phone, etc. are connect to this wifi normally.
  As there is no internet connection on my laptop, I downloaded "microsoft fix it" and installed in my laptop to another computer but it does not work, he showed me 3 tabs IE to read, etc. to fix it it is opening chrome Web site as there is no internet facility, displays "cannot display page" Web page
  so, please help me with this problem. feel free to ask all the necessary questions.
  Thank you
  Vandenplas, infant.

  Hi Vandenplas,

  Method 1

  Follow the advice given by Meghmala Feb 17,2010 on the thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/local-area-connection-does-not-have-valid-ip/72c61d55-4d20-48bd-80bf-cb25f7b95cb6

  Method 2

  Check the steps on the thread: http://windows.microsoft.com/en-IN/windows/network-connection-problem-help#network-problems=windows-7&v1h=win81tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Also check the discussion on the thread:'t-have-a/43ea076e-5210-4194-80d8-cb4681e852a0 http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/issues-found-local-area-connection-doesn

  If nothing helps, you can try to contact your ISP and ask them to reset the settings.

  Hope this solves the problem. If the problem persists, you can write back to us and we will be happy to help you further.

  Thank you!

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• Ipad Cisco ipsec VPN connects but not access to the local network

  Hi guys,.

  I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

  If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

  Cisco 877.

  My config is attached.

  Any ideas?

  Thank you

  Build-in iPad-client is not useful to your configuration.

  You have three options:

  (1) remove the ACL of your vpn group. Without split tunneling client will work.

  2) migrate legacy config crypto-map style. Here, you can use split tunneling

  3) migrate AnyConnect.

  The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

• Qosmio F60 - 11F - driver to connect to the local network

  Hi everyone help pleae this.

  I have a Qosmio F60 - 11F model and I have install Server 2008 Enterprise and I am facing a problem with the driver to connect to the local network.

  Please help on this issue.

  Hello

  Go to Device Manager and identify the provider/device id:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=78

  Then, perform a search on the page of the driver provider.

• Re: Satellite Pro A40 - connection to the local network

  Hello

  My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.

  When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,

  Then someone can point me in the right direction before as I have send myself crazy with this...

  You can

  regards and thanks in advance

  Andy

  Hey,.

  The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal

  I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
  ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h

• I can connect to the local network, but not to the internet

  Why in an internet connection, I can connect to the Local network, but not to the Internet.
  I have valid IP address and configuration is good.

  I recommend you read some threads here in the forum about similar issues.
  If this problem occurs using the WiFi network, then check if you can use the connection to the local network.
  Using the WiFi network, you must check if the common WLan parameters are favourable;
  Check if the encryption key is right; turn off filtering by mac address, check the TCP/IP protocol settings if it has been set to automatic, disable the firewall settings, rest you WLan router, check if you connected to the right SSID.

  Good bye

• Satellite A105-4114 will not recognize the connection to the local network

  Whenever I plug my cable ethernet to ethernet port on my laptop, the ethernet port does not recognize my cable, even if the lights are flashing. I updated my LAN driver a week ago, and it has not really helped. My internet service is provided by my apartment complex at the school, but I don't think it has anything to do with it, because I had this problem last year living in dorms and at home. I have to restart my computer everytime for my computer to recognize the connection to the local network. Can someone help me please?

  Driver: Intel (r) PRO/1000 PL Network Connection

  Wireless connection works fune.

  Hello

  First of all, you should check your LAN cable.
  Sometimes the laptop may not be correctly connected to the LAN as a result of a defective cable.
  In addition, you should check if the network card is properly recognized in Device Manager. He should t be a yellow exclamation!
  In addition, you must check the settings for the TCP/IP protocol in the LAN card properties.
  TCP/IP must be set to automatic. I assume that you are connected to a server and the server supports supported a range of IP addresses and assigns it automatically.

  Last but not least check if you are using the latest version of the BIOS.

  Welcome them

• Connection to the local network not appearing is not in network connections

  A month or so I reinstalled Windows XP SP2 (have since updated to SP3), and ever since then the LAN connection icon does not appear in the network connections window, and even when I plug the ethernet cable it does not automatically turn on the connection to the local network. My wireless connection works perfectly well. I went to the HP website to download all the drivers and also visited if the Device Manager on my computer to make sure that all drivers are in place. Even with all the drivers, it still does not connect to the local network. Help, please!

  Hi rawkous,
   
  Follow the steps listed in this article to resolve the problem:
  How to troubleshoot missing network connections icons in Windows Server 2003 and Windows XP

• Why if a system is xp and one system is windows 7 and the two connected to the local network, but file-sharing does not work

  a system is xp, another system is windows 7 basic and both connected to the local network, after you set up shared drive, mowing arrives not

  Hi Abhay,

  I suggest disable you the password protected sharing and check if it helps.

  Networking of computers running different versions of Windows

  Note: Follow the steps in the section "to enable sharing protected by password in Windows 7" and turn off password protected sharing.

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional