No initial Setup.

LLatest model Apple TV. Plugged into the back of the TV with cable h and that the selected channel.  Nothing happens on the screen.

HA reviewed correspondem implemented and found no problem.

Anyonewanna take this tar?  on what we can tru then.

FFaulty hdmi cable replaced and any fine.

Tags: Apple TV

Similar Questions

  • Can't see all networks wifi on initial Setup

    There was a problem with my original Touchpad (it does), so I sent to HP and just received my refurbished model. However, when I start the initial setup and it asks me to connect to a Wifi network, none appear, even if my network and my neighbors are all visible & active.

    My network configuration has not changed since my original Touchpad, which connected very well, so I don't know why this one should give problems. Any thoughts? It is extremely frustrating that I can still use my new Touchpad!

    Following my previous post, I called HP, explained my problem and they sent me a replacement. The new (renovated) came in a few days later and it connected to Wifi without problem. I proceeded to the initial installation and have no problem with this new unit.

    So, for all those who still have a problem with an inability to see any Wifi access during the initial installation points, contact HP and explain your problem. If you are able to upgrade to 3.0.4 use WebOS Doctor, do this and confirm that your Mac address is all zeros. This seemed to be the point of triggering of a replacement for me.

    Good luck to all! I'm going to use CM7 .

  • Initial Setup was never released?

    I just got a new laptop computer and any turning, he asked for my location and time zones. but then the screen froze and a login screen appears. I do not even have to do the initial Setup, and he brought me to the login screen. Is there anyone who knows also that or is this just me? I don't know what to do...

    You need to reinstall Windows 8:

    This is how the recovery partition is accessible to most popular brands...

    For Dell, press F8 on the keyboard until the Advanced Boot Options menu appears on the screen.

    For HP, press F11 directly after switching on the device

    For LG, press F11 directly after switching on the device

    For Toshiba, press and hold "0" BEFORE and during the power upward

    For Acer, press and hold ALT + F10, as soon as you see the logo

    For Asus, press F9, as soon as you see the Asus logo.

    For Samsung, press F4 to the power upward...

    For Fujitsu, press the F8 key directly after the power

    Advent, restart your computer. Then, press F10 repeatedly until the message "Starting system recovery"

    Sony VAIO, reboot and press "F8" or "F10" repeatedly until the screen "Advanced Boot Options".

  • QuickBooks does not install, it goes through the initial setup and then everything stops.

    I tried to install quickbooks, but after that happening by initial installation it just hangs.  I have error view in my computer management for setup of windows and checked to see if it has been activated (I put it on automatic).  Is there a windows update Setup program that I can download.  I use a windows vista computer.  Thank you.

    Hello

    Thank you for your response.

    1. what file did you try to install to the upgrade of Windows Installer 4.5?

    2. you use 32-bit or 64-bit operating system?

    3. what version of service pack is installed on your computer?

    4. have you tried all the steps mentioned in the post above?

    5. are you able to install other programs on the computer?

  • General error has occurred while trying to run the initial Setup Wizard

    Anyone have advice on the implementation of vCOPS?  I have deployed the ovf, use a Pool of IP and configure static ip addresses, I get to the login page (https://< IP > / admin) and when running the Setup Wizard initial on the front page of details of vCenter Server I get a message "General error has occurred", which does not allow me to go further.  Now, I closed the browser to try again and I get a "Virtual Appliance Repair" screen that also fails with a general error has occurred.  Can anyone help solve this?

    The vCOPS unit is version 5.0.1.0 build 677931

    vCenter is version 4.1.0 build 258902

    vcops_err01.JPG

    Thank you


    Dan

    Looks like you had a communication problem between two virtual machines.

    When you created the IP pool leave you this option disabled?  Also, you associate it with the same network that the virtual machines are connected?

  • After the initial setup time machine should be hard wired to the modem

    Should time machine be hard wired to the modem after initial installation

    Yes, if it must be used in its default configuration as a router DHCP network and all clients need to connect to the World Wide Web.

  • Wizard initial Setup screen

    Hello

    We have a Mac Pro OS X10.10.1 and password.

    By following the online solution, I deleted the file .applesetupdone:

    RM /var/db/.applesetupdone

    After reboot and enter the information in the form assistant configuration (username and password), the screen continue to return to the initial configuration wizard screen.

    Help, please!

    Also, when I go to single user Mode and redo "rm /var/db/.applesetupdone", it says no file found.

  • Initial setup for Xbox 360

    First switch off get a category for Xbox below. And my question, so I have the initial setting and now isn't the network who worked 5 minutes ago and nothing will work everything is blocked. I allowed family. I am extremely angry and nearby that have nothing to do with Microsoft. I had this bad luck with yall.

    I suggest you ask either in the Xbox Forums: http://forums.xbox.com/default.aspx or Xbox support: https://support.xbox.com/en-US/
  • Lost the initial setup of the user and cannot find the files in the my documents folder

    Thread: Recover original original put in place on window XP
    Recenty my Dektop HP (Window XP) restarted with recovery application. In the end, I lost my original CD all the user settings and can not find all my files in my documents folder. Doesn't have, I lost everything or is there a chance to go back to my original game. If ysé how can I do. He is workin OK but have Setup every thing with 4 users.

    Hello

    I fear that the computer was set to the resumption of the plant, all data and settings will be lost.
    I suggest you contact the manufacturer for the recovery of lost files.

  • Initial setup of the lab home

    Hi im new here, I bought some old used switches and routers and do a lab at home. I wanted to know if I need to console in each unit for initial config or if I config my first camera config the rest by the first device. I comforted in a switch 2950. I just want to know if I need to console in every device, whenever I make changes and others. Advice or tips would be appreciated

    I have

    switch 2 x 2950

    Switch 1 x 3550

    3 x 2811 routers

    Router 1 x 2520

    Hello Leo,

    indeed. The lines, you need to configure are the VTY lines, visible at the bottom of the configuration. A basic configuration that would allow all protocols including telnet and ssh would look like this:

    R1 (config) # line vty 0 15

    R1(config-Line) # password mypassword

    R1(config-Line) # local connection

    R1(config-Line) #transport of entry all

  • Initial setup for the module of firepower, where start

    Hello world

    Ask your help once again, first of all, I've read a ton of guide as to the initial configuration, i.e., initiate the module fire power so that covered.

    Recently, one of our clients bought a new ASA with services of firepower, all is well and good, until I saw that on the nomenclature, it has SF - FP5.3.1 - K9.

    As far as I know, admins are who will begin the device, for example, through to bootstrap and OUR system software desired.

    My question is, what I really have to go v5.3.1? or can I just jump to 5.4? for example, to download the software "bootstrap" of 5.4 and 5.4 sys
    Note This is a new ASA fresh-from-the-box-with-the-smell-of-cisco ^_^

    Hi LJ,.

    In this case you can directly jump to 5.4 because she didn't have any configuration.

    Kind regards

    Aditya

    Please evaluate the useful messages.

  • Rerun initial Setup

    Is there a way to remotely run the process of initial configuration on a fabric to interconnect via SSH without erasing the config?

    Hi Simon,.

    You can perform the initial installation via an interface not SSH. You can run remotely if you have access to the port of the two FI console.

    For the initial installation, you will need to clear the config and let the pole reconfigure and FI.

    . / Afonso

  • 5520 initial Setup

    I just unboxed a 5520 controller. Connected to the service port and access the UI to the default address 192.168.1.1 and configure initial values I want to use. Apply the settings, then the controller restarted. I can't access the GUI now.  Can I still plug into the service port and access 192.168.1.1 or do I plug into the port of Mgmt. and new GUI access MGMT address?  The controller is not connected on all switches, but as I am setting this up in my office before I bring it to our remote site.

    Thanks for any help

    R

    What happens when you connect a cable from the console in the way of the Console?

  • Are there problems with changing the IP address of a system of v5.3 ACS after the initial Setup?

    I'm migrating from ACS v4.2.1 to v5.3.  I want the final v5.3 system to assume the IP address of the machine 4.2 of origin so I don't have to change any configs on network devices.

    Are there problems with the change of the IP address of the system AFTER the initial installation v5.3?

    I tried without problem. I changed the ip address of the WLC several times.

    You must ensure that:

    1-) you change the switchport accordingly to the appropriate vlan if the new ip address belongs to a subnet of a vlan different.

    2-) make sure that all clients AAA configured to use the new IP address of the ACS servers.

    Here is the procedure how to change the ip address of the interface (according to the doc of cisco):

    http://goo.GL/0BYqVT

    I also changed parIP normal address and it works. but of course, the server must be autonomous before doing this step (i.e. no secondary ACSS registered to him and he is not on the other ACSS in a distributoin).

    HTH

    Amjad

  • Initial setup of Orchestrator: Plugins not properly configured

    vCO_plugins1.png

    I got most of the way through the initial configuration of the vCO device 5.1 but I'm stuck at this point and can't find what kind of credentials, I need to enter the user name: field (I think)

    vCO_plugins2.png

    I have successfully configured authentication to use our Active Directory, I have created a new group for administrators of VCO and identified the unique name of this group on the Authentication tab.

    Any help is greatly appreciated.

    Brian

    It works if you leave these fields empty right?

    If this is not the case, try the username@domain syntax to specify the user name.

    See you soon,.

    Joerg

  • Please help me with iSCSI software initiator setup in ESX.

    Greetings,

    I have a DELL MD3000i SAN with two controllers. Each controller has both for the multipath iSCSI network interface cards.  I've always used CF so I'm a little nervous in the implementation of iSCSI network on ESX. Please help me.

    Controller 1 port 1 is the IP 192.168.253.2

    Controller 1 port 2 is the IP 192.168.254.2

    2 1 joystick port is the IP 192.168.253.3

    2 2 joystick port is the IP 192.168.254.3

    I have Setup VLANS on my level 3 for switch vlan 253 and 254.  IP addresses are 192.168.253.1 and 192.168.254.1 respectively.

    My goal is to set up a fully redundant connection with failover support, but I can't enter the network on ESX configuration.

    I intend using two network adapters in an active / standby (one active NETWORK card on a VLAN, put on hold for the other and vice versa) configuration.

    Can someone please tell me exactly what to do to ensure the fully redundant connectivity?

    Thank you in advance.

    Yes. This look is good so far.

    http://blog.laspina.ca/

Maybe you are looking for

  • Tweak Firefox default tile (new tab) to make it as Speed Dial.

    Is it possible to tweak the default Firefox tile (new tab) to make it as Speed Dial?For example, google.com adds the first tile, firefox.org on the second, etc... It is possible to do without having to download add-ons? Thank you.

  • Satellite P850 - 12Z USB 3.0 Ports right side do not work USB 3.0 speed

    Hi all I bought a portable Satellite P850-12Z with * 4 * USB 3.0 ports. Two ports on the left side and two ports on the right side with sleep functions and fresh. If I connect an external drive Verbatim USB 3.0 ports on the left side, everything work

  • HP PAVILION 17-F061NB: for games cooling pad?

    Right then, the story made short: I recently (a few months), bought a HP Pavilion 17-F061NB computer laptop computer laptop, which I use mainly for games. It has a processor AMD A10, with 12 GB of ram, and and AMD Radeon R7 M260 dedicated graphics ca

  • CHANGE ADMINISTRATOR PASSWORD

    My uncle gave me his computer, but he died since & I don't have one of his passwords. I need to change the settings of the administrator. How can I do this?

  • Some problems with the upgrade of RAM on Lenovo ThinkPad T500?

    Hello My laptop is Lenovo ThinkPad T500 and its main features as follows: -Processor Intel Core 2 Duo T9400 (2.53 GHz, 1066 MHz, 6MBL2). - 4 GB PC3 - 8500 DDR3 SDRAM 1067 MHz SODIMM Memory (2 DIMM). -ATI Mobility Radeon 3650 with 256 MB. I really nee