No outgoing call - don't bug?

Similar Questions

• Outgoing calls are limited by a FDN

  All,

  Since today morning I am not able to make calls outgoing/incoming calls receive. It gives a message "outgoing calls are limited by the FDN. I checked under the call settings, it displays the NDR is disabled... I don't know wht happened... any help on this...

  Knani.

  Can you tell me who this phone was purchased? Operators in India have begun using the GSM database for security reasons. Your phone does not work with most networks in India because

  1. your IMEI number is not a commercial IMEI (this means that the phone was not purchased from TMO)

  OR

  2. your phone has been reported, lost, stolen or defective

  If you think that your phone has an IMEI commercial and/or has not been reported stolen, lost or defective, you can try your luck with your provider network in India to see if they can get your IMEI added to the database of GSM.

  Vodaphone, it appears is currently not using the basic GSM data to check the IMEI and it will be just a matter of time before you do that because that would be charged by the Government for security reasons. Hope that answers your question.

  BTW, the error message on FDN that you see is a bug with the mapping of the error incorrect. The real reason is, your phone is denied registration with the network because the IMEI number is not authentication.

• [SPA112] No sound when the outgoing call

  I installed my new SPA112 with an EdgeRouter.

  Router config:

  Pass port 5060-5061 to the SPA112

  Before port 16000-17000 to SPA112 (also tried 10000-35000)

  SPA112 Config:

  NAT: EXT IP, Keep Alive (my ISP does not use a STUN server, tried another server STUN, still the same problem)

  Line: Mapping enabled NAT, NAT Keep Alive.

  The SPA112 is registered with the SIP server.

  The problem:

  When I call someone, the person can here me, and I can here the person.

  When someone calls me, I can here the other person but the other person can't here me.

  See the TXT for incoming and outgoing call.

  Incommingcall.txt: Problem with audio to go to the other person

  Outgoingcall.txt: No problem with audio

  When I call someone, the other person hears me and I hear them.

  Of the most important messages for outgoing calls ( incoming , below). Commented by me.

  [0:0]CC:STUN OK:192.168.1.8->83.247.45.219, 5060->5060 16388->16388

  STUN has detected that your external address is 83.247.45.219, the same port numbers by NAT.

  [0]->212.45.38.48:5060(979)INVITE sip:064.....[email protected]/*  */ SIP/2.0Via: SIP/2.0/UDP 192.168.1.8:5060;branch=z9hG4bK-f6bed01From: "3134.....99" [email protected]/*  */>;tag=b66f15e1852bc1c4o0To: [email protected]/*  */>Remote-Party-ID: "3134.....99" [email protected]/*  */>;screen=yes;party=callingCall-ID: [email protected]/*  */CSeq: 101 INVITEContact: "3134.....99" [email protected]/*  */:5060;ref=3134.....99>User-Agent: Cisco/SPA112-1.4.0(001)
  
  o=- 136114 136114 IN IP4 83.247.45.219c=IN IP4 83.247.45.219m=audio 16388 RTP/AVP 8 18 2 0 100 101a=rtpmap:8 PCMA/8000a=ptime:30

  Call setup. Audio stream Incommimg asked to be sent to 83.247.45.219:16338. It is in the transmitted range (16000-17000).

  [0]<<212.45.38.48:5060(817)
  SIP/2.0 183 Session Progress
  Via: SIP/2.0/UDP 192.168.1.8:5060;received=83.247.45.219;branch=z9hG4bK-da26c2e5
  From: "3134.....99" [email protected]/*  */>;tag=b66f15e1852bc1c4o0
  To: [email protected]/*  */>;tag=SDhgdq997-127.0.0.1alUtKGp-09645+1+5c310006+2c2bae2a
  Call-ID: [email protected]/*  */
  CSeq: 102 INVITE
  Server: Alcatel-Lucent 5020 MGC-8 8.1.0.16.SP8.5
  Contact: [email protected]/*  */:5060;transport=udp>
  
  o=- 3656610554 3656610554 IN IP4 212.45.38.48
  c=IN IP4 212.45.38.48
  m=audio 63808 RTP/AVP 8 101
  a=ptime:20
  a=rtpmap:8 PCMA/800

  Of the other answer for call setup. Coming out of the audio stream asked to be sent to 212.45.38.48:63808. He is outgoing don't stream so no special arrangements on recalcitrant NAT. It doesn't look good in the direction of the cabin, is not so surprising that it worked.

  When someone calls me, I can hear the other person but the other person can't hear me.

  
  Most important messages for incomming call (for outgoing see above). Commented by me.
  

  [0]<<212.45.38.48:5060(789)
  INVITE sip:3134.....[email protected]/*  */:5060 SIP/2.0
  Via: SIP/2.0/UDP 212.45.38.48:5060;branch=z9hG4bK8jld5h207grg5v4up6m0.1
  From: [email protected]/*  */:5060;user=phone>;tag=SDgcm0c03--45026-3668cfa-2d96f01c-3668cfa
  To: [email protected]/*  */:5060;user=phone>
  Call-ID: [email protected]/*  */
  CSeq: 1 INVITE
  Contact: [email protected]/*  */:5060;transport=udp>
  
  o=HuaweiSoftx3000 1115218122 1115218123 IN IP4 212.45.38.48
  c=IN IP4 212.45.38.48
  m=audio 63316 RTP/AVP 8 101
  a=rtpmap:8 PCMA/8000
  a=ptime:20
  

  Configuration of incoming call. Coming out of the audio stream asked to be sent to 212.45.38.48:63316. He is outgoing don't stream so no special arrangements on recalcitrant NAT.

  [0]->212.45.38.48:5060(918)
  SIP/2.0 200 OK
  To: [email protected]/*  */:5060;user=phone>;tag=430df31719850825i0
  From: [email protected]/*  */:5060;user=phone>;tag=SDgcm0c03--45026-3668cfa-2d96f01c-3668cfa
  Call-ID: [email protected]/*  */
  CSeq: 1 INVITE
  Via: SIP/2.0/UDP 212.45.38.48:5060;branch=z9hG4bK8jld5h207grg5v4up6m0.1
  Contact: "3134.....99" [email protected]/*  */:5060>
  Server: Cisco/SPA112-1.4.0(001)
  Remote-Party-ID: "3134.....99" [email protected]/*  */>;screen=yes;party=called
  
  o=- 165329 165329 IN IP4 83.247.45.219
  c=IN IP4 83.247.45.219
  m=audio 16392 RTP/AVP 8 100 101
  a=rtpmap:8 PCMA/8000
  a=ptime:30
  a=sendrecv
  

  Our response to the incoming call configuration. Audio stream Incommimg asked to be sent to 83.247.45.219:16392. It is in the transmitted range (16000-17000). It seems not good in the direction of the cabin. According to statistics BYE...

  P-RTP-Stat: PS=990,OS=166160,PR=594,OR=142560,PL=0,JI=0,LA=0,DU=17,EN=G711a,DE=G711a

  ... SPA112 sent 166160 B/990 packets of audio data at the other end. I see no outgoing audio problems. Call person to hear. Well, despite the packages are OK at the time, they may not be the same at the receiving end. You have active SIP ALG feature on EdgeRouter? SIP - LG is known for having questions about so many routers, which one of the Uniquity. In addition, you should not combine STUN on SPA112 with SIP - ALG on router. Please turn off ALG SIP on the router. If it does not solve your problem, then ask provider upstream assistance. We need SIP & RTP packets captured on the side of the trunk. A note unrelated to your problem. It seems that you SIP-> settings-> value 0.030 RTP toRTP packet size . It's a suboptimal value for your upstream provider (in fact it is bad everywhere in Europe). Your provider uses 0.020 (according to the settings specified in the INVITATION). Consider the same value. It can increase the sound quality (for the end-user of the other).

  This message contains information related to the site of the other so it may contain information considered to be sensitive or confidential.

  Consider the notation of the useful comments. It can help others find solutions.

• CSCum85086 - outgoing calls by RL omitting, RG members reported as inactive

  We encounter this bug on the version 8.6.2.23045 - 1. Reconstruction of the bridge in CUCM arranges for us.

  Does anyone know if this bug is fixed in version 8.6.2.25900 - 8 (SU5)?

  Hi Joey,

  According to the Readme of 8.6.2.25900 - 8 (SU5), this bug is resolved caveats. You can find details

  http://www.Cisco.com/Web/software/282074295/116467/CUCM-Readme-862asu5.PDF

  Solved CUCM implemented 8.6(2.25130-1); BASIC for 8.6 SU5 (2A)

  CSCum85086: outgoing calls by default RL, members of the RG reported as inactive

  Kind regards

  Ronak Agarwal

• SOLVED blackBerry smartphones - cannot make outgoing calls. Get two beeps like busy tone with the Koodo Mobile in Thunder Bay, Ontario North

  This has caused me a lot of frustration.

  With my curve when I try to make an outgoing call and I get a busy signal as two beeps repeating themselves.

  I tried everything and the only thing that worked was a security wipe, so losing all my data.

  If I made a backup and restore, the problem comes back. If I restored it selectively through desktop BLackberry, database of the database, the problem returns. Koodo Mobile and Blackberry escalated support was not able to understand this.

  However, through much trial and error, I found that if I limit my identity or turn off the option to show my number in the phone settings, for some reason any he caused this problem.

  So I can't block my identity by using the settings on the phone.

  This can be the result of my location service and the carrier, which is Koodo mobile, in Thunder Bay in Northwestern Ontario that used the TBAYTEL towers for the service, the type of signals technology service. I don't know, and no one was able to tell me why this is happening. I went to 6 months not being able to make outgoing calls without losing ALL my sms, contacts, BBM, TXTs, bookmarks and other personal data. Only a security wipe would allow me to make a call - until I have activate the restrict my identity and activated the show my number option.

  SO - I hope this helps other users. I've been through three phones, thinking that it was the material problems.

  It's a kind of crappeh because I would not block my identity with a few calls. So with the curve BB on Koodo to Thunder Bay, I can't do that. I have not tried outside the Northwestern ONtario, but it will probably be the same, unless I am out of service TBAYTEL area.

  Such is life. Live with it.

  Difficulty easy but unsatisfactory.

  I ' lll this post in the Forum of Koodo so when one exists.

  See you soon!

  I did these steps including restore each database one at a time with the same results. I can do a full restore and the remains of the issue until I set restrict my identity forever AND Show My Number Yes. I also did all of these steps with the any other BB Curve 8530 and it seems to happen every ih in this area.

  I found the work around but it would be good to know why and if this happens outside the TBAYTEL towers that Koodo Mobile uses throughout Northern Ontario to the Ontario-Manitoba border in the West, to the North of Hearst and East of Sault Ste. Marie.

  If there are a Koodo Mobile, users who have a BlackBerry Curve 8530, I'd like to hear you just what I see if it is unique to the service provider, hardware, software and network type, geographical location, etc.

  Any comment is appreciated, as support Koodo and BlackBerry have been baffled and couldn't solve this problem and I hope that others find it so that they can save months of time and frustration, I have lived.

  See you soon...

• Outgoing calls not showing does not on other devices of continuity

  I'm showing incoming calls (both missed and received) but no outgoing. I would like to have a complete call log on all my devices. Is this just how continuity works or am I missing something?

  I suggest relying on the Web site of your mobile operator for more information on all outgoing calls.

• iPhone os SE 9.3 (last) why outgoing call attributed to me when I didn't call and actually blocked the number when I received an unsolicited, a week ago the same call?

  Why is there an outgoing call this morning from my iphone os SE 9.3.2 to a number that called my phone Friday unsolicited and which I blocked immediately?  I got no call number.  1. how an outgoing call could be made from my phone?  2 is not a number of blocking prevents the contact incoming or outgoing?  What should do?

  Contact your operator.

• Skype outgoing calls will not connect

  Skype was working fine on my Macbook Pro for months, but all of a sudden when I try to call someone, it just says: connectin and call then ignored, it's only a problem with outgoing calls because it allows me to receive and answer incoming calls. does anyone know how to fix this? Thank you.

  I did too much work!

  System Preferences > Security & Privacy > firewall > unlock so that you can change the settings > Firewall Options > find Skype and allow all incoming connections > Hit Ok > (now that you're back in system preferences) > privacy > accessibility > check Skype > Lock changes > fact

• Outgoing calls accompanies this number online?

  Outgoing calls also included in the purchase of an online number?

  Hello

  No, outgoing calls are not included.

  If you want to make calls from Skype then you need a subscription or a credit of Skype.

  For more information about the number online, please visit: https://support.skype.com/en/faq/FA331

  I hope that helps!

  If my answer helped solve your problem, mark it as a Solution to help others.
  Thank you!
  
  Please send messages private by request only.

• SPA9000 outgoing call won't. Get the "busy" signal and "CallEnded" message.

  Hello

  I have 9000 SPA with SPA400 and 8 configured SPA941. Everything worked up until the service has changed the proxy. Now because of them I'm trying to configure a iristel Line3 lines. Incoming calls are coming. But not able to make outgoing calls using the iristel line. I tried to change the line. No use. Can be Server NAT is a problem. I use the LAN and the router is WRT300N. How do I enable port forwarding and what are the values of beach to give? Any help welcome.

  Thank you. Hope it will work. I did the port forwarding today on WRT300N. To see the results tomorrow. Hope that the SIP line will remain registered until tomorrow.

• BlackBerry Z10 Z10: outgoing calls

  Bought a Z10 and it rained until recently.

  Outgoing calls stopped working episodic. That is, the phone starts to make a call, the inscription on the 'Call Waiting', then 'E' ('H' icon) turns into 'e' icon for a second and the message on the screen "call ended". Can I mistaken with the translation (I see messages on my tongue).

  the same time, everything works fine. I can receive calls (!), write text messages or use e-mail.

  Phone starts to function normally after some time

  My Z10 is very cool, but when it does not perform its main function...

  It may or may not be bound even if entrants are OK

  You can try this to see if it helps: when powered on hold the button works for 10 seconds, this resets the phone.

  To see if it is carrier or a tower of transfer issue try this: settings, connections network, Mobile network, network selection Mode, manual change, if the Scan does not start automatically, press Scan.

  When the Scan is complete, choose your network, if any other enumerated arer do not choose their that will not work.

• How to listen to the incoming/outgoing call events?

  I am using the phone interface and the onCallUpdated method, but the id does not work on incoming/outgoing calls.

  Are there examples of code or something else?

  It has:

  access_phone
  

  Try and tell me if it works.

• SPA112: no possible outgoing call after incoming call

  I've recently set up a SPA112 with a SIP account and a connected analog telephone. The SPA is a Netgear FVS318G-router firewall enabled SIP - ALG. Everything works fine - I can make outgoing calls and I can receive incoming calls - with the exception of the following:

  Shortly after the end of an incoming call (phone hang up) it is not possible to make an outgoing call. The tone is there, but after dialing, nothing happens. The called party has reported having noticed the incoming call, but no voice cannot be heard.

  A few minutes later it works again.

  It does not happen after outgoing calls.

  Seems there is a synchronization problem, but I was not able to determine which parameter is bound to.

  It seems that audio stream does not pass through the firewall.

  To check settings and firewall logs. You can enable syslog & debug on SPA112 and also well catch them - it can help you analyze the question.

• How can I judge an incoming or an outgoing call?

  Hi all.

  How can I judge an incoming or an outgoing call?

  I use

  PhoneCallLog phoneLog = (PhoneCallLog) logs.callAt (i, PhoneLogs.FOLDER_NORMAL_CALLS);

  phoneLog.getParticipant () .getName ();

  Can I get the name of the call but do not know if this is an incoming or outgoing call.

  Any suggestion? Thank you

  PhoneCallLog.getType)

  See the javadocs.

• BlackBerry Smartphones BB torch: call the cuts after every 1 hour with the error message: forbidden outgoing calls (8 CC)... .plz help

  The flame of my BB, cutting its call after every 1 hour with the error message: forbidden outgoing calls (8 CC). except the active calls, isn't she the netwrk...?

  Hey pemba.

  Welcome to the community of BlackBerry Support Forums.

  Thanks for the question.

  I would first check to see if you are using the latest version of the software of your network service provider.  Go to www.blackberry.com/update or open BlackBerry Desktop Software.  If the software is up to date, I would check with your provider network for more investigations.

  Let me know if you have any questions.

  See you soon.