No repeaters between Cisco Aironet 1250 and equipment cisco config

Similar Questions

• 4 Aironet 1250 and a controller?

  Hi guys,.

  I'm about to order a four Aironet 1250 and a Wireless LAN Controller 2106. What I've read, I'm going to need the controller to manage access points if I want that they offer the same broadcast domain and subnet and offer roaming for users. Often times what I have read and understand it turns so little to do with reality, so my question is, do I right about that?

  Thanks in advance!

  Joe

  Hey Joe,

  210 x WLC doesnot support mode of transport Layer 2... support mode is the Layer 3. Yes, we can have the APs in the same field of dissemination that is, APs and WLC management and Manager of the AP in the same subnet works and it uses IP header instead of the Ethernet frame.

  We can connect the access points and clients can roam between. We need to ensure what WLC software takes care of 1252 and use the same or later.

  Concerning

  Surendra

• Problem with VLAN between Cisco Catalyst (3560G) and SG300-52

  I am having trouble with the creation of a trunk of vlan between a SG300-52 and a Cisco Catalyst 3560 G.  I have 4 VLANS (1, 2, 10 and 11) on the 3650 and I need ports on the SG300 to be able to communicate with them.

  On the 3560, port 14 is defined as:

  interface GigabitEthernet0/14

  switchport trunk encapsulation dot1q

  switchport mode trunk

  spanning tree portfast

  On the Sg300 port 52 is defined as:

  interface GigabitEthernet52

  point to point link type spanningtree

  switchport trunk allowed vlan add 1,2,10,11

  description macro switch

  Try to understand what the problem... Any help would be appreciated.

  Thank you

  Chris

  Hi Chris, the first problem is the spanning tree portfast, it shouldn't be on an interconnection network switch. You may have a mismatch of vlan native as well, but that shouldn't matter.

  A suggestion, however, the value of the port SG300 general mode and disable the input filter.

  -Tom
  Please mark replied messages useful

• difference between cisco NAC agent and cisco Clean Access Agent

  Hi all

  If anyone has the idea on different between cisco NAC agent and cisco Clean Access Agent, please let us know your ideas.

  Thank you

  In 4.6, the agent has been revised and is now called the NAC agent.  Previous versions were called the clean access Agent.  So roughly, 4.5 and 4.1.3.2 agent are own access agents, and agents 4.6.x and 4.7.x are called NAC agents.

  Some of the changes are moving a lot of the agent configuration in an XML file, redesign of the GUI, adding a service portion (of the sort that the agent of heel is no longer necessary) and the best journaling agent.

• Basic questions of configuration Cisco Aironet 1250

  Hello

  I'll be three Aironet 1250 within a building.  It won't be a wireless controller, the AP will be autonomous.  I'll put them all the same thing, with WPA2 wireless encryption.  My question is, what is important and beneficial to add the configuration to the s AP so that they are aware of the other (for roaming maybe)?  If Yes, what is this technology called and someone could direct me to a section of a guide that could illustrate this?

  Or I'm fine with just stand-alone configuration 3 AP as it is.

  All other pointers are welcome.

  Thank you!

  Hello

  If you use the pre-shared as an authentication method, so there is nothing special to do. As long as they have the same SSID, are in the same subnet and are connected to the same network, roaming will be fine.

  No specific configuration is required.

  Nicolas

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Site to Site VPN between Cisco ASA 5505 and Sonicwall TZ170

  I'm trying to implement a VPN site-to site between our data center and office.  The data center has a Cisco ASA 5505 and the Office has a Sonicwall TZ170.  I managed to configure the two so that the vpn connects.  Each of the firewall I ping the IP Address of the internet firewall on the other side and a desktop computer I can ping the IP Address of the firewall internal datacenter but I can't carry traffic between private subnets datacenter and desktop.  Can anyone help?

  The config below has had IPs/passwords has changed.

  External Datacenter: 1.1.1.4

  External office: 1.1.1.1

  Internal data center: 10.5.0.1/24

  Internal office: 10.10.0.1/24

  : Saved
  :
  ASA Version 8.2 (1)
  !
  hostname datacenterfirewall
  mydomain.tld domain name
  activate the password encrypted
  passwd encrypted
  names of
  name 10.10.0.0 OfficeNetwork
  10.5.0.0 DatacenterNetwork name
  !
  interface Vlan1
  nameif inside
  security-level 100
  10.5.0.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  1.1.1.4 IP address 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS server-group DefaultDNS
  buydomains.com domain name
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  inside_access_in list extended access permit icmp any one
  inside_access_in list extended access permitted tcp a whole
  inside_access_in list extended access udp allowed a whole
  inside_access_in of access allowed any ip an extended list
  outside_access_in list extended access permit icmp any one
  outside_access_in list extended access udp allowed any any eq isakmp
  IP DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0
  IP OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0
  outside_cryptomap_66.1 list of allowed ip extended access all OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 ip OfficeNetwork 255.255.255.0 allowed extended access list all
  outside_cryptomap_66.1 list extended access permit icmp any OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 list extended access allowed icmp OfficeNetwork 255.255.255.0 everything
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP verify reverse path to the outside interface
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route inside 0.0.0.0 0.0.0.0 1.1.1.1 1
  Route OfficeNetwork 255.255.255.0 outside 1.1.1.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 10.5.0.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-aes-256 walthamoffice, esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto dynamic-map ciscopix 1 corresponds to the address outside_cryptomap_66.1
  Crypto dynamic-map ciscopix 1 transform-set walthamoffice
  Crypto dynamic-map ciscopix 1 the value reverse-road
  map dynmaptosw 66-isakmp ipsec crypto dynamic ciscopix
  dynmaptosw interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 13
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  lifetime 28800
  crypto ISAKMP policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  Telnet 10.5.0.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 10.5.0.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd address 10.5.0.2 - 10.5.0.254 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 66.250.45.2 source outdoors
  NTP server 72.18.205.157 source outdoors
  NTP server 208.53.158.34 source outdoors
  WebVPN
  attributes of Group Policy DfltGrpPolicy
  VPN-idle-timeout no
  username admin password encrypted
  tunnel-group 1.1.1.1 type ipsec-l2l
  tunnel-group 1.1.1.1 ipsec-attributes
  pre-shared-key *.
  !
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  !
  context of prompt hostname
  Cryptochecksum:7f319172e5de9c0e550804a263f8e49e
  : end

  Mattew, obvious lack of education is the rule exempt from nat for your tunnel, your access list pixtosw is similar on this example, I assume that you have gone through this link, if it does not see the configs on both sides.

  Add the statement of rule sheep in asa and try again.

  NAT (inside) 0-list of access pixtosw

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008052c9d4.shtml

  Concerning

• IKE Dead Peer Detection between Cisco ASA and Cisco PIX

  I have a network environment in Star with about 30 offices of satellite remote using VPN Site to Site connectivity.  The majority of remote satellite offices have the features of Cisco PIX 501 running PIX Version 6.3.  The hub office runs a version 8.2 (1) Cisco ASA.

  I configured Dead Peer Detection on the Cisco ASA device at the office hub with the default settings of the following-

  Confidence interval - 10 seconds

  Retry interval - 2 seconds

  I think I'm right assuming that raises are limited to 3 before the tunnel is completely demolished.  Basically, the problem that I am facing is with several remote satellite offices.  What seems to be the case, the tunnel between the remote offices and the hub is demolished (probably because of the length of IKE, always 86400 seconds) and the tunnel then fails to renegotiate unless traffic is physically forced from the hub office.  The tunnel NOT to renegotiate after satellite office, ONLY the end of the hub; so that means sending traffic to the satellite when the VPN tunnel is out of service, not to renegotiate the tunnel.  The Hub office is a colo and therefore traffic rarely comes to that end, the tunnel remains so down until manual intervention occurs and the ICMP traffic is forced into the tunnel.

  Should the KeepAlive and retry interval settings corresponds to both ends, for example if the two devices be configured for DPD?

  What are the potential pitfalls to the extension of the life of IKE, and this will help or even hinder the problem?

  Thank you in advance for helping out with this.

  Hi Nicolas,.

  I think that the two DPD settings must match on both ends, if these do not match then problems like yours might arise which seems to happen here, is that one end shows a tunnel down, but the other end may not detect it down, we could have to watch debugs, or record two ends to see if this is the case , setting in the meantime ike DPD for same timers could hetlp on.

  In regard to the increase in the life expectancy of IKE, well you just need to be aware that this could allow keys to be discovered since these are not renegotiated unless the tunnel is down on the level of IKE. Other than that I don't see why this would affect you.

• Aironet 1200 and MAC authentication

  Hi all

  I Aironet 1210 and you want to implement the authentication MAC without ACS.

  Now, I know that any AP Aironet can allow authentication MAC se store the list of MAC addresses.

  So after the command:

  TestAP (config-if-ssid) #authentication open mac

  TestAP (config-if-ssid) #authentication open mac address?

  WORD mac address list (1-31 characters) name

  There is no way I can list all MAC addresses in the list. I use IOS Version 12.2 (13) JA3.

  Any help would be greatly appreciated.

  Kind regards

  Samuel Wilson

  If you do not have a RADIUS server on your network, you can create a list of MAC addresses allowed on advanced security of access point: MAC address authentication page. Devices with not on the list of MAC addresses are not allowed to authenticate.

  I use the GUI to make a list:

  http://www.Cisco.com/en/us/products/HW/wireless/ps4570/products_configuration_example09186a00801c0912.shtml

  The link above is to use the local capacity of GANYMEDE to the AP, but if you select the option "Advanced Security" on the right side of the web interface, it will take you to the page where you can create your list of mac addresses.

  Please evaluate the useful messages.

• What is the difference between the service SmartNet and SMB level

  Good afternoon

  I would like to ask if what is the difference between Cisco SmartNet and Cisco SMB service level?

  Thank you

  Hey Rey,

  SMARtnet covers traditional Cisco products (products of the company IE.) ISR routers), Small Business Support Center covers the line of small business.

  In the Group of the UC products, for some reason, Cisco believes the UC520, AP521, and WLC526, which are small business to be traditional Cisco products and brand SMARTnet are covered. But, the UC540 and the UC560 are covered by HWC. A major difference in the area of the CPU is the support for CLI vs CCA config.

  However, I noticed your message in small business - class switches. If you have a switch of small business people who are covered by HWC not TAC. HWC will support the CLI and web gui configuration of switches in small businesses, where the CLI is applicable to the model.

  HWC contracts tend to be 3-year periods and can be significantly cheaper than SMARTnet agreements.

  Hope that helps.

  Best,

  David

  Please evaluate the useful messages and identify the right answers.

• Communication between the device IDS and router test

  I use a 4210 sensor, S47 Version 4.0 (2). I'm waiting on the upgrade memory provided under the contract until I can update above.

  Is there a way to test telnet between the detection device and the router? Stop ping at the firewall (we allow all ICMP traffic). I can't find a command 'telnet'.

  Thank you!

  John Kingston

  You must create a service account configuration mode (conf t) then:

  user service private service pass

  Sign out then as cisco, then reconnect you as a service. Telnet now works

• Is it possible to send an alert through TMS when a crossing box fails between a VCS - C and VCS-E?

  Hi all

  TMS has many features to alert, but I don't see an easy way to alert us to the fact that a crossing area may have failed between a VCS - C and VCS - E, or even neighbor or other types of areas than peers with other devices. Is this possible?

  As we now have a large number of VCS, it is important for us to know that these peering is active. It is not necessarily the case that individual machines become inaccessible, just the interconnection network fails for some reason any.

  Thank you very much

  Chris

  As much as I know tms cannot do that, she must be a feature request.

  / Magnus

  Sent by Cisco Support technique iPhone App

• I was wondering what the difference was between the powerbeats 2 and the powerbeats 3. What is this new "chip" in the powerbeats 3?

  I was wondering what the difference was between the powerbeats 2 and the powerbeats 3. What is this new "chip" in the powerbeats 3?

  Hello

  Main differences are:

  • Up to 12 hours of battery life with Powerbeats3, which use chips to W1 Apple energy-efficient (vs. up to 6 hours of battery life with Powerbeats2).
  • A quick charge of 5 minutes for a typical use of an hour (vs 15 minutes to load).
  • Improved ergonomic design.

  More information:

  http://www.Apple.com/shop/product/MNN02LL/A/powerbeats3-wireless-earphones-shock-Jaune

  http://www.beatsbydre.com/earphones/browse-earphones/wireless-earphones/ML8V2.ht ml

• How can I compare prices between iPhone Upgrade Program and refinancing?

  I wonder this for years, and it's how can I see how much is a new iPhone (say if I am refinancing a 6 s 16 GB iPhone), how much will cost each month and how much an iPhone cost in case of upgrade program. So if we are on the upgrade program, can OK, I buy it in the stores of carrier? What are the benefits of refinancing? Can I exchange a phone located to midway between the refinancing period and use the program to update iPhone and will I pay less each month? And after 12 months, what I have to pay the tax and the money to upgrade to a new iPhone, or is it just continue to pay $32 per month?

  Visit their Web sites. All the details are there for you to browse and decide what suits you best. Only you can decide.

• New window creates a gap between the Favorites (top) and tabs (bottom)

  19/12/14 bug Firefox began to occur:

  • When having only 1 window open and opening tabs behaves normally.
  • However, when you open a new window of the space between the bookmarks (top) and tabs (bottom) spans all windows. Its boring.

  So far only challenge is to just close and open 1 single window, or to use the module 'Classic theme restaurateur' and switch the tabs position from the bottom to the top, but all new windows will open the gap again.

  Image below.

  Unfortunately, none of these options works, so far, use 'CTR' and turn the legs up (default) allows the opening of new windows without gaps.
  Seems to be some sort of bug recently showing on CTR.

  You will need to find a way to contact the developer to let them know.

  EDIT: It seems to be resolved, seems a new version was released and the problem disappeared. Thank you very much for the help.

• Dropbox for bookmarks or downloads of the navigation bar adds space between the navigation bar and bar bookmarks.

  When I press the button edit bookmark or download the toolbar for navigation that a line of space appears between the navigation bar and the bookmarks toolbar. This problem is corrected when I start Firefox in safe mode, but not when I boot normally and disable all addons. Please tell us how to solve this problem. Reseting Firefox and install all add ons still causes too many problems, so I hope to be able to solve this problem without reset.

  [url =http://postimg.org/image/uwr2x6x21/] [img] http://S28.postimg.org/uwr2x6x21/space.jpg line / URL

  You can also try to delete the file localstore.rdf (resets the toolbar configuration) in the case of its corrupt.

  • http://KB.mozillazine.org/Corrupt_localstore.RDF