No signal after call
I really want to keep complaining about the update. Especially since I waited for this for a long time. I like a lot of changes. I like the new UI, animations of the lollipop, the new voice of the bike, the new view of the bike with the additional information (except the ' fixing' of the vague bug!) But! A new bug, I've noticed, is that immediately after the end of a call (even after the rejection of an incoming call) the signal disappears for 1-2 seconds. Then he comes back! The reception is very good, where I am currently. It happens after each call, and it's boring! If anyone else noticed that?
It is a problem of old age (I'm talking about Greece )
https://forums.Motorola.com/posts/9caa9a2bea
You have to live with it, no one of Motorola or forums will help... I had this problem since I bought the phone even after that and I got replacement and even after the 5.1 update.
Tags: Motorola Phones
Similar Questions
-
Satellite L450 - 13G - No WLAN signal after a few minutes
Hello. I just bought a L450 13 G with Windows 7 pre loaded.
I noticed that a lot of times drops wifi connection. It starts as an excellent signal and then suddenly fades to no signal after a few minutes. I can't get it remains connected, if I'm in the same room or the next day. I have also a few years L or U 200 (I think) and it remains connected wherever I am at home.
What could be the problem?
Hey Buddy,
I assume you are using the preinstalled version of Windows 7. Is this good?
If so try to update the WLAN driver. If you are looking for your laptop model, you will find the latest version on the Toshiba site.In addition, check the configuration of the router. If you use a MAC address filter, try to disable it. Try another encryption and password encryption.
Also check the firmware if you use the most recent one. -
Port resets the value after calling DAQmxStopTask.
Hello? My device is PCI-6025E and I used to reset by sending 0x00 on #0 with DAQ digital output port. It must be reset if the VC software button power ++ is pressed.
But after a trial of DAQmx, even after that I sent 0x00, it will be set the value of 0x00 to 0xFF after calling DAQmxStopTask. I want to know how do I know it's 0x00, ahead of DAQmxStopTask.
I tried to read the port #0 when writing of 0x00 in this regard, but it hangs or it returns error; He said that the port is reserved and can not read the port until the task (in writing) is completed.
Here is the code that I tested.
error int = 0;
TaskHandle taskHandle = 0;
TaskHandle DItaskHandle = 0;
uInt8 data = 0 x 00;
char errBuff [2048] = {'\0'};
Int32 wrote;
Int32 read;
uInt8 dataToRead;
bool32 bTaskStatus;DAQmxErrChk (DAQmxWriteDigitalU8(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,)); creaded the 6.5.2009
DAQmxErrChk (DAQmxIsTaskDone (taskHandle & bTaskStatus));
DAQmxErrChk (DAQmxWaitUntilTaskDone (taskHandle, 1.5)); 6.5.2009{if (bTaskStatus)}
Reading test - DI on written port0-/ / / 6.5.2009
DAQmxErrChk (DAQmxCreateTask("",&DItaskHandle)); 6.5.2009
DAQmxErrChk (DAQmxCreateDIChan (DItaskHandle, "port0/Dev1", "", DAQmx_Val_ChanForAllLines)); 6.5.2009
DAQmxErrChk (DAQmxStartTask (DItaskHandle)); 6.5.2009
DAQmxErrChk (DAQmxReadDigitalU32(DItaskHandle,1,10.0,DAQmx_Val_GroupByChannel,&dataToRead,1,&read,)); 6.5.2009
printf ("acquired data: 0x%X\n",dataToRead "); 6.5.2009}
Try to use the node property DAQmx to reverse digital lines.
According to the that you configure DI / use the following
Int32 __CFUNC DAQmxSetDOInvertLines (TaskHandle taskHandle, const char [channel], data bool32);
Int32 __CFUNC DAQmxSetDIInvertLines (TaskHandle taskHandle, const char [channel], data bool32);
Kind regards
Glenn
Technical sales engineer
National Instruments
-
Amplitude of the Signal after the FFT analysis
I'm currently trying to find the amplitude of a signal after running a FFT analysis. I use this for image analysis MTF. I take the profile of the line of fire (with an alternation of black and white bars) and convert it to a signal. This signal is then introduced to a FFT Mag/Phase VI extent and output of the FFT. My program then enter the amplitude to frequency of alternating black and white bars.
My problem is that the amplitude seems to be scaling by a factor. I would like to find the exact amplitude of the signal of my analysis. Anyone know the factor of scale or any problem with my program? I joined the program and the image that must be analyzed. Just browse to the image in the VI and run the program and you will see the MTF chart resulting.
Thank you
Ronak
-
The monitor loses signal after some time
During the installation of windows vista, the monitor would lose the signal after some time (the screen turns black and does not) while the computer is still on. I am currently using ATI radeon hd 5750 and I tried to connect two monitors to the video card and it wouldn't work (both monitors loser of the signal)
Hi PaulYea,
1. what type of Installation are you trying? It's an upgrade or clean Installtion?
2. what happens when you connect to the system now?
If you attempt an upgrade installation, then try the update the video card drivers and check:
Update drivers: recommended links
http://Windows.Microsoft.com/en-us/Windows-Vista/update-drivers-recommended-links
You can also check out the link to the manufacturer to download the drivers:
You can also try running Upgrade Advisor and start the upgrade installation
Check out the link:
http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor
Note: This also applies to Vista.
For more information, see the link:
Solving Windows installation problems
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Windows-installation-problems
Hope this information is useful.
-
How can I activate the zoom pinch after calling preventDefault();?
I created a chart in the edge animate which should work correctly on both the iPad and desktop computers. The html file that I create will be then fired in an iframe on a Web site as part of a larger page. I've included touch events and mouse for interactive elements, and most of the time it works fine on the desktop and iPads - except for when it is not.
I found in my tests that sometimes a mouseOver/mouseEnter or even a click event fires despite my use of the e.preventDefault (); in my events touchStart or touchstart (I tried both). The behavior is not coherent enough for me to determine why this is happening so I have a solution for the moment - I've added preventDefault(); to touchStart in document.compositionReady:
$(document) .one ('touchend', Function {}
e.preventDefault ();
});
I understand that this is not ideal, but with deadlines and all that noise, it's the best solution I found to this day.
It works perfectly, but as expected, it also disables the pinch zoom and pan. I don't care panoramic, but the zoom is necessary because the data points on the graph are on the small side. Can someone help me with the code, I would need to enable pinch zoom after call preventDefault()?: Or the conditional statement that would go preventDefault(); on a regular/single touch but not a pinch of touch zoom?
I use v2014.1.1 to edge host CC on a Windows 7 machine, if it is useful.
I cannot share my code because of the confidentiality agreement to my company, although if necessary I can probably model a simple sample - I'm hoping someone out there with more experience in the development of contact devices can point me in the right direction.
Thank you!!
Melanie
This refurbished - Box dots.zip version handles the events of iOS. See private message.
Tested: iPad (iOS 8.1.3) and MacBook (Mac OS 10.10.2) and Safari 8.0.3
I will post a final version to improve the change of color and the text box.
-
Space by default after calling model sup
Hi all
I call template void in the report of the rtf header. Even if there is no space between the header and the title of the report, when the preview image shows a gap between the title of model output and sub report. There are no spaces in the sub model. Is that it default rtf creates spaces after calling model sup in the header?
Thank you
Sushil
Your sub-model code includes the text "DW DISCOUNT DATE:" in a table? If so, edit the property table in your subtemplate-> skin-> autour
I think I sent you a model modified by e-mail and which included the fix.
Thank you
Bipuser
-
Using Flash Player on Windows machines, since the Flash Player 11.4 version - Flash Player 15 (ActiveX version) and every version after that we had a problem in which Hauppauge PCIe and Videology cameras or other non-standard devices it does not work with Flash Player after calling getCamera() so many times. For example, we get the camera and publish a netstream for 10 minutes, then we have the camera set to null. Later, we call the camera again and after doing this 25 times or 100 times, the camera driver just seems to fail, and Flash Player is as is the streaming of the camera, but the NetStream info indicates zero-byte data video aired by indicating that there is no pixel coming from the camera.
Someone else knows this problem to where you need to restart the browser or the Windows for Flash Player process power getCamera() properly again?
Yes, it seems that others have experienced a similar problem. Adobe has not yet confirmed that it is a bug, but it is followed here:
Bug #3850401 - handle with video.attachCamera leak leading to the unusable device
-
No signal after you have unlocked the new iPhone 4S
Just got my brand new (sealed box) Vodafone 4S managed to unlock via iTunes, put my existing (of work) O2 Sim in and waited for 24 hours to see that I have NO signal. 3G (internet) and everything works fine but impossible to send or receive calls, messages, etc. Have tried every conceivable reset and restore anything will do. Were informed by O2 customer service that the issue is now with the phone... So, what the * is happening and how to fix this?
There is no such thing as a 'new' iPhone 4S. He was suspended for years.
If you think This is new, check the warranty here: https://www.apple.com/legal/warranty/?cid=acs:applesearch
If it is defective, have it replaced.
-
WE157AA #ABU: showing no signal after a pure fan
Hi, I have a 3 year old HP Pavilion Office. I often clean the fan because dust accumulates really and the fan is noisy. Take it works fine after a good cleaning. However this time the computer started as a normal fan runs fast & you hear the welcome tone and other computer sounds, start-up but the display shows 'No Signal'
I tried to turn off the computer by pressing the 4 or 5 seconds and then restart, but it makes no difference. I did this several times.
The fan will slow down normally & becomes silent once the computer has booted, but he is staying on at full speed this time.
I have no other choice than to completely shut down the power button.
It is not the monitor & just to be safe, I connected another monitor & same poblem. No signal.
Thank you for your response. It has none of the steps mentioned in the document. I read in another post on stirring the fan which is what I did and it worked. It has been fine since.
-
No Signal after installing new graphics card
Hello and thank you in advance for your help!
We have a 2 years old HP p6540y. It has an ATI video card integrated. When we recently turned on, we got a message "no signal" on the monitor and then he'd go to sleep. We tried many things to fix... listed below, in order and are always the same message. Please advise!
(1) No Signal: DVI, VGA, HDMI. So we unplugged and rebooted, no change.
(2) checked monitor and DVI & VGA cables with another computer: they all work.
(3) installed new graphics card: NVIDIA GEForce GT 610. Still got same message "no signal".
(4) we plugged/unplugged all the other cards/cords / no matter what we could and cleaned. Then, finally, the monitor turned on! But not for long...
(5) after you restart the computer after installation of the graphics card driver, we got the 'no signal' message again. We released once more, other cards/sheets and again once the monitor and the computer came to life.
(6) we uninstalled the ATI integrated graphics card. When we go to display, Advanced Options, he mentions our new NVIDIA as graphic/video card.
(7) we turned computer off during the night and this morning when we have lit, we once agin got the message "no signal". We have unplugged/plugged computer several times. Also tried the trick with cards/plugs by pulling and we have nothing. No Signal. After doing this several times (about 10), he is finally working again.
(8) we changed the sleep settings to: screen saver = never; Standby mode = never.
(9) we restarted again to get once more no signal message.
So... what should we do?
Thank you very much!
Triusa, welcome to the forum.
I think that your problem is caused by the power supply unit (PSU). Here's a guide to help you solve the problem:
http://support.HP.com/us-en/document/bph06788
Also, the existing PSU is 250W. The 610 GT requires a minimum of 300W.
If your problem is solved, please click "accept as a Solution.
-
Summary after call message balance or usage data
I have lenovo s 820 it is not whose record after making a call, message or by using the data connection, how do I turn it on...
try to install USSD to notification fm google game it solve my problem even in P780
https://play.Google.com/store/apps/details?ID=com.Aeon.ussdtonotificationof course restart handset after installation
-
So far, I had a hell of a trip to the scene that I have (I managed to get windows 7 booted up and installed etc and then had to download drivers for a bunch of stuff that was absent because of the falling out between W7 and W8) but I need serious help/help - particularly nearby wireless network card drivers , but also in other areas, too.
In short, the problem I have is that I had to download an ASUS 802.11n network adapter driver just to get my wireless works... and now it is not picking up signal unless the laptop is basically right next to the router.
The router works fine - it's all new Virgin Media and I pick up the signal 5 houses down on my iphone.
I guess the question I seek an answer to is if because the Windows 8.1 will no longer work and I had to install a * beep * ty Asus driver temporarily, can someone find me a suitable adapter for the following:
PCI\VEN_14E4 & DEV_4365 & SUBSYS_2230103C & REV_01
PCI\VEN_14E4 & DEV_4365 & SUBSYS_2230103C
PCI\VEN_14E4 & DEV_4365 & CC_028000
PCI\VEN_14E4 & DEV_4365 & CC_0280Oh my laptop is a HP pavilion 17 by the way - and Yes, I used this site to get adapters but none seem compatible.
After spending some time looking around more closely, I found a driver that solved my problem:
-
Monitor says no signal after moving the computer
need help to make the monitor iluminate
My windows xp is just moved to another room with a new distance map and functioning. After the move, the monitor says no signal! The computer and the monitor seems to work but the screen goes black after showing NO SIGNAL and goes to sleep.
One step at a time.
Also, I would also like to make these windows xp and windows live units communicate with each other in my home group.
Bill enjoy life
Hello
I suggest you to check the physical connection that is connected to your computer?
I suggest you to follow the steps and check.No input Signal message.
Cause
This problem may be caused by one of the options below.
- Monitor not connected correctly.
- Faulty hardware
Solution
Monitor not connected correctly
Verify that the monitor is connected to the back of the screen, as well as the back of the computer.
If the monitor seems to be connected correctly, check that a cable is not loose by disconnecting any cables that may be disconnected at the back of the screen (usually the data cable cannot be disconnected). Then unplug the data cable connected to the back of the computer, and then reconnect the cable. By connecting the cable to the back of the computer, ensure that the cable connection is strained. Most computers will also have the ends of screws that can be screwed to keep the connector in place.
Faulty hardware
If the connections look OK, unfortunately it is likely that the monitor or the computer graphics card is bad. To test this component is bad, either connect a different monitor to your computer or connect your monitor to another computer.
-
Difficulty with returns control to the parents program after call asynchronous Subvi
I'm trying to set up a directory of context-sensitive help for one of my programs. This is the first time I tried an asynchronous call and I can't seem to make it work properly.
The attached HelpDir.vi is the parent program that gives the user different help files to choose. When the user selects a help file, its Subvi should appear. I would like the user able to let this help file upwards and close the help directory or select another help file to upsimulataneously, if they wish.
The strange thing is that, currently, this vi works exactly as I want if I stress execution on, but works normally, the HelpDir.vi becomes unresponsive when we help files was loaded and becomes sensitive again once the help file has been left.
I set up the parent program with a structure of the event running asynchronous call and forget everything as in the example of the expedition to the France so I do not know why the program parent is not recover control after the launch of the Subvi. Please take a look and let me know if you see what I'm missing.
PS, You may need to update both static references. I don't know if they break when you send the code this way.
Thank you
Tim
Change your dialogues float instead of Modal. Modal windows will always be on top. In the changing Floating, then you can access the window of your main VI as well.
Performance highlight should substitute somehow the disorder of modal window.
Maybe you are looking for
-
I just got a text asking me to verify my apple ID
Hello This may or may not be in line with this post on but I just got a text asking me to verify my Apple ID. It gives me a link that brings me to a screen where I need to connect my Apple ID and password. I haven't done this yet. I was wandering if
-
I have a new laptop and I am a newbie on the laptop. I inserted a cd but now how to get out? Of course it is obvious on the desktop what do, but not on laptop.
-
dv9207us: dv9207us: 4 GB of Ram installed, but only 3 GB useful?
I have a dv9207us laptop with 4 GB of ram installed. BIOS shows 4 GB of ram, but said information system control panel 4 GB installed (3.0 GB usable). Anyway to get the full 4GBs? Details: -------------------------------------------------------- 8.1
-
Can't send or receive emails, error 0X800CCC90 & 0x80042OCD
Original title: OX800ccc90 & Ox80042OCD error message Error message OX800ccc90 & Ox80042OCD may not send or receive any
-
Hi, try to change the regional settings programmatically and I coded as follows... but I didn't observe any change in locale. I've added the necessary resources for the corresponding locale. Here is my code... ButtonField btn = new ButtonField("Chang