No Signal to the monitor, keyboard, or mouse HP 110-023w running 64-bit Windows 8.1 desktop

Similar Questions

• PC runs, but does not start. Monitor, keyboard and mouse with no signal.

  PC runs, but does not start. Monitor, keyboard and mouse with no signal. Pretty much. And when you want me to remove the battery of the bios, or whatever, it seems tight and hard to get out because it is surrounded by other elements.

  All fans work, the power/battery or anything that works I think that, since there is a fan on the right where it is and it seems to work. I remember what happens before, I don't know, but before that, there are many gels. This error below was made before all this happened, but I managed to run f8 and then run normally until it freezes again. Then, after that, it runs but does not start. No beeps etc. The best fans will have plenty of vouches and Bravo to wherever you like me to vouch or maybe send the great service that you provide to administrators if that's even possible, haha.

  Thanks in advance.

  "

  The file is possibly corrupted. The file header checksum does not match the checksum calculated. »

  It is a sign of a lack of food.  Looks like you have a desktop computer?

  Power supplies run about $50.  It is a rectangular box at the corner of the system in which the power supply will from the outside.  It's a pretty standard form in most of the PC and with a little investigation thorough replacements can be found.

  It is usually held in place by 4 screws and can be held in place with a spring clip.

  Most essential, is that you need to buy a replacement with the right number of straight plug forms to adapt to your PC.

  This seems more complicated than it really is and takes about 5 to 10 minutes to do the replacement.

  Look at the power output of the power supply failure and buy a new, more powerful.  New desktop PC usually come usually with a diet under size and what are the causes these failures is too strong a request for devices you have connected.  So, buy one with a higher power rating.  Usually about 500 Watts does the trick.

  If you do not feel upwards to this task, a technician should not charge you much like this.

• 750se envy: envy of the brand new office no signal to the monitor via HDMI

  Just got my new 750se envy and 25 x 25 backlit monitor. After putting it all together, I connect the monitor of the Tower via HDMI. Tower boots, display lights, I pop in setting up the drive, but the monitor says that it cannot find a signal. I test my old monitor to the new Tower (a monitor of series pavilion aged 7 years). Same results. The Tower seems to be the treatment given that you can hear what it read the disc.
  
  I take another hdmi cable and and test exactly as described above. New monitor, new Tower and new hdmi cable still no signal. Old monitor, new Tower and new hdmi cable still no signal.
  
  Just to be sure, I plug my new monitor to my old HP Pavilion desktop computer. Tower lights up as usual, and the new monitor immediately comes to life with color. I can safwly guess it's the tower. I open the side panel and check all jacks to make sure they are warm and fully attached. Nothing seems to be loose or out of place.
  
  I start to sting online for answers. I met this reset of the BIOS. Press F10 to 8 seconds, down, 3 times arrow, enter twice and restart. Nothing. Still no signal. Can I assume there is something wrong with the Nvidia GeForce GTX 960 and windows the cause? Maybe turn hdmi ports are messy? It was the only other subjects I really found on the issue. Everything seems to work, just no signal between the monitor and Tower.

  89kowens

  Since it is a relatively new machine, instead of hurt for hours to fix yourself, why not just let HP repair at our expense!
  
  You must contact the HP Customer Support directly so they put you in contact with HP Tech Support to see what they can do on the diagnosis and repair of your machine remotely.
  
  I did recently, and HP technology was able to remotely access my PC on the Internet and to make the necessary repairs.
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  Good luck

• Cannot find the driver for a PSC 2175 in list of 64-bit Windows 7 for HP printers

  Cannot find the driver for a PSC 2175 in list of 64-bit Windows 7 for HP printers.  Can anyone help?

  In fact, the way to solve the problem was to open devices and printers, click with the right button on the icon of the HP psc 2170 Series and use troubleshooting icon.  Who finds the driver, thank God.  Found this just by chance!

• I accidentally deleted the directory "C:\Program Files (x 86) \Microsoft ' my 64 bit Windows Vista system. How can I get it back?

  I accidentally deleted the directory "C:\Program Files (x 86) \Microsoft ' my 64 bit Windows Vista system.  How can I get it back?

  original title: C:\Program Files (x 86) \Microsoft

  You can try this program:

  http://www.filehippo.com/download_recuva/

  Use the deep Scan option. It may take some time.

  The System File Checker can repair some of the files in there, but probably not all.

  It's probably at least some of the files that have been overwritten. so I would say the the more safe thing to do is to reinstall Windows.

• 64-bit virtual machines will not work on the new computer running 64-bit Windows 8

  
  My new computer running 64-bit Windows 8. I installed WorkStation version 9 and the virtual machines have 64-bit operating systems will not work.

  have you turned on VT in the host system BIOS?

• HP Z820 workstation: Z820 HP does start, fans at high speed, no BIOS, no signal in the monitor.

  Hello world

  My listing of workstation: HP Z820, Dual Xeon E5-2687W @ 3.1 - 3, 8 GHz, graphic card Nvidia quadro K5000, 64 GB RAM, 2 x 500 GB HARD drive.
  The workstation is still under warranty.

  They arrived after upgrade to Windows 10 (from 8.1 to Windows) and put such BIOS updated as recommended by HP support Assistant.

  I was on the process to refresh the 10 Windows , then the system automatically tried rebooting to complete the update, but he never did it again! and then the fans running at full speed. After waiting for 2-3 minutes, I had to hold the power button to turn off the computer.

  After waiting for about 10 minutes, I tried to start the computer, but the same thing happened: you press the button power and then after about a minute , fans rotating at high speed, no signal, no BIOS, no noise, no power in the keyboard or mouse, the blue LED light to the rear.

  So I let the computer without power for 7 hours... (The power cable is disconnected).

  At 11:00: reconnected the power cable (HDD and DVD ROM are DISCONNECTED) and tried to start but the same thing happened.

  Now, I'm on google to find a solution:

  1. power? (Have not yet been tested food.)
  2 motherboard? No damage to the capacitors or anything else.
  3 reset the BIOS/CMOS? (Power disconnected cable) Removed the battery and put it back it, held the CMOS button for 5 seconds.
  4 graphics card? Replaced the K5000 Quadro with a Quadro 4000.
  5. exercise of the power of the system? held the power button with the power cord unplugged for 30 seconds.

  None of the above solves the problem but now when you press the power button / the fans start to run at high speed immediately! This got worse?

  Any help would be greatly appreciated. Thank you.

  The problem is a faulty motherboard and it was replaced under warranty.

• Using two computers on a single monitor, keyboard and mouse.

  I want to use my two computers with a single screen, keyboard and mouse... says to use the kvm switch.  I use Windows XP on a computer and Windows Vista on the other... what kvm switch do you recommend?

  You can view the free software kvm solution below:

  Input Director
   http://www.InputDirector.com/

  I use between three computers (1-Win7 Pro x 64 single monitor, 1-WinXP Pro x 86 two monitors, 1-WinXP Home x 86 single monitor) and a single keyboard and mouse. It works fine for me, I used it for over a year without any problems. The Win7 Pro and WinXP Pro have both run several virtual machines too.

  There are several other kvm software available (Google is your friend) I tried several before input Director.

  Kind regards

• Desktop HP Pavillion Mini: unify dongle that connects the wireless keyboard and mouse on the HP Pavilion Mini Office

  I bought the product online at Amazon.com. I lost the unifying dongle that connects the keyboard and mouse wireless for the mini PC. No knowledge of a store selling the usb dongle online in the USA? Here is the data on the area where the mouse: model number: MG-1451 / 1452-RG, country of origin: China, identification number of the KCC: IPMPC-CRY-HPK-MG-1451 and IPMPC-CRY-HPK-RG-1452. Help, please. Thank you.

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.
  If you are unfamiliar with works as a private of the Forum messages, this post has instructions.
  http://h30434.www3.HP.com/T5/first-time-here-learn-how-to-post-and-more/how-to-check-your-messages/TD-p/3547355

• Intermittent message "No Signal" on the monitor

  I have a dual monitor Setup and everything worked perfect for a year or two until I've had a deadlock and restart to get the gel.  Now, monitor #1 has work fine except is has a small window in the middle that says no signal.  From time to time the black monitor and then come back on without this little message, but then the message reappears.  Any thoughts?  Thank you

  I checked a similar script posted here and the solution that worked for me, so far.  I turned off the computer, has turned off the display, disconnected the cable (both ends), reconnected the cable (both ends), turned on the monitor, started the computer.  Problem solved.  Thank you!

• Signal of the monitor no. reads at startup!

  The bed monitor no siganl on the start screen happens with video for the boot of drivers it works bar green drivers run cursor monte on the screen.and loses the screen and right when it breaks at the newspaper to remove the OS on its cuts on hard black on the rise on the desktop, then reads no signal.  I can here the audio and about 10 seconds later for windows OS chimes makes all the way until I have just the monitor. I can boot into safe mode. I tried to set a lower resolution on the start, reload the video drivers. System Restore and all the boot options in the list of repair. I use a Proview LCD connected to my laptop via the VGA port I cracked the LCD screen on the top of the Tower, so I unplugged. It was working fine forover a month I tried to reconnect the laptop LCD makes no difference. I see nothing in Event Viewer. I did fix it it app on the MS site and said it make small repairs.  t

  video was not one of them.

  Hello

  Make sure you have power on the monitor cable.  Test it on another computer if you can.

  Remove the power cord and hold the power button on the system.  (Hard stop).  Plug the cord in and re - turn on the system.

  Now you have Visual on the screen?

  Check your system RAM modules - try reinstalling module in an empty slot

  Run Memtest 86 to test memory

  http://www.Memtest86.com/

  RealTemp is a temperature monitoring program - check that you're not overheating

  http://www.techpowerup.com/downloads/1691/real-temp-3-40/

  Seagate tools - HDD controls

  http://www.Seagate.com/support/downloads/SeaTools/

• Windows 10 does not recognize the wired keyboard and mouse

  When I start windows 10 technical preview my mouse and keyboard do not work.

  they are recognized when I'm in the bios, but when it does start nothing

  keyboard and mouse wired usb

  This is the forum for Windows 7.

• How to use the Arc keyboard and mouse Arc using the same USB Transceiver?

  I bought a bow from Microsoft and Microsoft Arc mouse keyboard.

  Both devices come with their own 2.4 GHz USB tranceivers.

  I want to connect the keyboard and mouse to a transceiver.

  I can't find any instructions on how to do it.

  In comparison, my Logitech keyboard and mouse comes with software that allows me to pair several devices to the same Transceiver.

  How to connect the keyboard and mouse to a transceiver?

  P.

  As far as I know, you can do that.  If you want the keyboard and mouse on a transceiver, you buy a keyboard/mouse kit, commonly known as a desktop computer.

• Uninstall the usb keyboard and mouse

  I am swapping a USB keyboard and a USB mouse for a combo keyboard and mouse Logitech MK360 wireless on my Dell Optiplex gx620 desktop (Windows 7).  Do I pull up the Device Manager, go to the properties for the keyboard and the mouse and click on uninstall BEFORE or after HAVING physically remove connectors USB keyboard and mouse to the USB ports on the Office?  Should I use before removing connectors USB Safely Remove Hardware?  Thank you

  USB keyboard/mouse can be disconnected without using the icon "remove."  In fact, I would be shocked if they were still on the list safely remove at all.

  But to answer your first question, which depends on whether you want to keep pilots autour for future use.  If this is not the case, go ahead and uninstall the device before unplugging.

• Keyboard and mouse not working not not after resetting Windows 10

  I have a Dell Inspiron 530 on win 7 now upgraded to win10 1 to August 15. All good until a few days ago, when my wireless keyboard and mouse began paying up, keys not giving the correct characters or symbols. I found a site that offers to win 10, that I did a reset and now I have a PC that looks perfect on the monitor, but not on keyboard. I can't control or use the PC. I plugged my old KB & mouse USB but still no controls in Windows, I tried searching the keyboard and USB settings in the BIOS but can only find switches to change the speed high or low speed USB, tried two and no change. I can't find any advanced settings.

  I tried to find a way to get into safe mode to make changes, but I can't find how to do this without KB or mouse.

  I have a 2nd PC on Windows 7 is anyway to prepare a flash drive to download a fix. I have a 16 GB flash drive.

  I would appreciate any help with this problem

  Best wishes

  Dai

  Hello

  Thanks for posting your query in Microsoft Community.

  This could be due to problem of incompatibility with the keyboard and mouse drivers. I suggest you use another computer and download the latest compatible keyboard/mouse drivers with the latest operating system (Windows 8.1 is). Download the drivers in the flash player and then install the same drivers in Windows 10 machine and check.

  If the problem persists, install the same driver in compatibility mode for an earlier version of Windows.

  a. do the driver installation file right click and select Properties and then tap or click on the compatibility tab.

  b. check in the run this program in compatibility mode for: box.

  c. press or click the menu drop down and select a previous operating system, and then tap or click OK.

  d. try to install the driver and verify.

  Please refer to: make programs more compatible with this version of Windows (information is good for Windows 10 institutions)

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.