No sound after updating the BIOS, no error mssg.

Similar Questions

• After updating the BIOS, speakers produce no sound and iTunes and WMP did not recognize media files.

  Hi people. I got an update of the BIOS that has been installed automatically today. Since the update I lost all sound to my speakers and for the most part, my headset plug into the socket. I ran troubleshooting (States that the speakers are working properly), I rolled back and updated the drivers audio, quadruple checked all the settings, did a hard reset... nothing seems to work for her. Have no idea while iTunes or WMP won't play all my music now. Any help would be greatly appreciated. Thank you! (I have a HP Pavilion dv7 entertainment notebook running Windows 7)

  Hey vélorution,

  I see that you are having a problem with not getting no sound after upgrading the Bios.

• Problems after updating the BIOS on Satellite Pro P200

  I recently buy a Satellite Pro P200 running Windows Vista Business. Yesterday, I updated the BIOS to the version 1.50 supplied with the machine to 1.80 available on the Toshiba site. I double checked that I was using BIOS correct update for the Pro P200 Satellitel running Vista.

  After updating the BIOS, I have now two problems:

  1. whenever I start and join the office, I get an error message "record of Vista has stopped working". This problem has been identified as toshibavistaregistration.exe here: [link: http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=99805]

  2 Control Panel > system now shows the processor and the memory (RAM) as "not available". Execution of the diagnostic PC Toshoba tool and looking at basic information show also no information on the memory (RAM) Although the processor information here. There may be pieces others missing too under the eyes of list shorter than before the update of the BIOS.

  Basically, I want to get everything working again as it should, but cannot find any information on these issues.

  After further review, it appears that the update of the BIOS is not the cause of the problems.

  Immediately after updating the BIOS, I had a major system crash. It turns out that this is what has caused problems.

  After a system restore to a point before the update of the BIOS and the major system crash, now everything is working again with BIOS version 1.8 in place.

• HP Pavilion Notebook - 15-p206: WiFi lost after updating the BIOS of HP Pavilion Notebook - 15-p206tx on windows 10

  Hello
  
  WiFi lost after updating the BIOS of HP Pavilion Notebook - 15-p206tx on windows 10.

  Update driver BIOS update effective system is rebooted and the wifi does not.
  
  Please help me.

  In the box to Ask Me whatever it is next to the Windows icon, type in "Installed updates", and then click view installed updates.

  Select the update that is dated from when you had the question.

  Click it to uninstall.

  You have to restart the laptop afterwards.

• G72-a20EM screen has stopped working after updating the BIOS F.48.

  How is it possible that BIOS update recommended could turn off the LCD screen.

  Currently I see almost anything on the screen, but vga port works. But increasingly,.

  Intel graphics card is not recognized.

  G72-a20EM screen has stopped working after updating the BIOS F.48.

  What can I do to fix that?

  Good news!

  I found the working version, and it is version F.08.

  Supposedly new version have different Active cables, and this is the reason why the screen is dark.

  So, case closed, everything is perfect.

• Satellite Pro 6100 - after updating the BIOS, it does not

  Hello

  I am trying to upgrade my old of Satellite Pro 6100.

  I started to upgrade the Bios via download from Toshiba (using WIN) site - OK downloaded zip files and installed, machine then stops. Problem, it does not restart - it's so now I have a laptop 'death' that is not responding to any key I tried.

  Any suggestions of resuscitation?

  Already I've updated from XP to SP2.

  Thank you

  Paul

  Hello

  It sounds like that the BIOS update has failed and your laptop can start t again. But try this workaround:
  Remove the AC adapter and the battery and then wait an hour. After that reconnect the adapter AC/DC and battery. Try to start the laptop.

  If it doesn t work I think that the motherboard needs to be replaced or you go to an authorized service provider. Technicians can reflash the ROM module
  But maybe you can find a motherboard of second hand cheap on eBay

  Good bye

• Satellite L300 - 20 d - after updating the BIOS, that it does not start now

  Hello

  I bought my wife a Toshiba L300 - 20 d (PSLB8E-0CK00YEN). It came with loaded Vista, which it cannot do.

  My grandson offered also to sort. He has installed a new hard drive, loaded with XP and managed to get almost all the drivers working except the WiFi.

  After spending many hours, he decided to update the bios of v1.8 to v1.9. Since it does not start... It happens with the Toshba screen, start windows normally, then it attempts to load windows, flashing and start the cycle al.

  He has tried default settings, tried a XP disk, setting on the disk, nothing. He just does the same thing in safe mode.

  Any suggestions will be appreciated

  Concerning

  Keith

  Hello

  The wireless network card is enabled with the hardware switch on the computer laptop and FN + F8? Check this box!

  Additionally, make sure that the latest driver on the Toshiba site is installed, and check the settings of the wireless network adapter TCP/IP.

  Moreover a description that is more accurate than the WiFi works not would be very appreciated.

  Good bye

• Satellite A-C50-K9K - after updating the BIOS, cooling fan is very loud

  Gas station proposed to update the BIOS. 1.00 to 1.30. After updating the cooling system is 90% of the time. Load the default settings BIOS do not change.

  No backup of the BIOS. Is it possible to download BIOS 1.00 or solve this problem?

  The downgrade of the BIOS is not possible because you n t have the first version of BIOS and even if you get the 1.0 version of BIOS, the BIOS update procedure is not possible because the newer version is already flashed.

  But I recommend you set the method in Windows to optimize power or better management the cooling battery life

  + Control Panel--> Power Options--> change the parameters of plan--> change power avancΘs--> TOSHIBA Power Saver Settings--> cooling method.

• X200T not boot from any device after updating the Bios v3.00

  Hello

  I recently updated my bios to the latest version, the v3.00 X200T and now it does not start from any device - everything I get a blank screen after the initial bios starts upward.

  The bios seems functional and it recognizes all the devices I attached, as well as the internal hard drive. However no matter how to start the machine it does not start. I tried to set the boot order in the bios, using F12, F11 for recovery, remove the internal HARD disk, used all the USB ports, etc... -all I get is a blank screen after the initial splash screen.

  No beeps to indicate any problems, and I tried to reset the default settings of the bios, remove battery & power - all to nothing does not.

  Any ideas?

  I updated the bios of many laptops and desktop computers in the past, but this is a new one on me...

  I hope someone can help.

  Darren

  It seems that it also happens to X 200 owners who upgrade to version 3.01 of the Bios.

  mc2sgp has posted a response in this forum that worked for me:

  "I have the same problem and found the way to a temporary solution."  Go into the BIOS (you should always be able to press F1 to go into the BIOS) and go to Config-> CPU Intel VT - d characteristic of-> and disable it.  You should now be able to start normally in your operating system. "

  At least, I can now start my camera.

  Hope this helps others.

  Darren

  ADMIN edit: tagging this post as the solution to guide others to the bypass.  Lenovo will remove the BIOS on the web and replace it with an updated version that resolves these symptoms as quickly as possible.

• Tecra A2: brightness F6 Fn + F7 does not work after updating the BIOS of the screen

  Update bios to 1.40 VICTORY at end of January. Since the failure of keys F6 & F7 then to increase or decrease the brightness of the screen. Is it a coincidence or is that updating the bios the culprit! ??

  Hello

  Usually, the update of the BIOS shouldn't have a bad influence on the drivers of Toshiba and the performance of the operating system.
  There must be another reason the FN key down.

  Initially, I would say to reinstall the common modules. Please check if this will help.

• Satellite A100-920 - after updating the BIOS, it does not start

  Hi all

  I've updated the BIOS of my laptop to V6.0 (excerpt from the Toshiba site) then Windows XP and it went well, then Setup wanted to restart the PC.
  But restarts, he won't have in the startup process. I can not access the start menu, or anything else by clicking F2 or F12. But could go the detailed process by clicking on escape. And there I see the following messages:
  
  Phoenix TrustedCore (TM)
  V6.0
  Version.Mak - r1.53
  detects the dual core [email protected]

  No TPM or TPM has problem.
  1023 M system RAM passed
  

  And that's all.
  I can not get older versions of BIOS, and I couldn't find the version of the version 6.0 update that I could put on a CD for an another BIOS update.

  Anyone has an idea on what is wrong? And if you find that it's to do with version 6.0 and I need a previous version, please could you send me the installation files that are necessary to do the update via a CDROM.

  Thanks for your help.

  It is unclear to me that you can do the BIOS update using CDROM. The BIOS updates are designed to be done under operating systems. Old traditional updates have been a little different.

  In any case, it seems that the BIOS chip is damaged. I can imagine this downgrade can help but where to find the old version. I know you can get it from the authorized service provider. they have access to the database of Toshiba and they can download the old version of the BIOS.

  The download page is just the latest version available.
  Contact the nearest service and ask for help.

• Satellite P100: After updating the BIOS 3.8 I can't access MCE pressing enter

  Hello!

  I was able to enter XP MCE by pressing the Enter key when the Welcome screen. Now I cannot and must click on the photo of the small image. Is it because of 3.8 BIOS that I put in place recently or not? Can I do this option still works? Thank you very much.

  Hello

  I put t know if you can restore this option but you should access the BIOS and try to define again the default settings t.
  Don t forget to save the settings if you exit BIOS ;)

  But I really don't understand why you have updated the BIOS. If the laptop is running without any problems a BIOS update is not necessary!
  Therefore, never change a system up and running, you know? ;)

  Besides as I know the P100 were not delivered with Microsoft XP MCE but with XP Home and Express Media Player or Vista

• After updating the BIOS, there is no sound from my computer.

  I just updated my computer with a new BIOS and there is no sound.

  Very disappointed with HP. I tried a hard reset and it did not work.

  My product is hp pavilion g6

  Product number: QE06UA #ABA
  OS: Windows 7 Home Premium 64-bit

  Hey, Dan:

  I don't have your model of PC, so here's some generic instructions.

  Turn on the PC and at the beginning of the HP welcome screen, press the F10 key to access the BIOS.

  There should be a menu to save the default settings and the outputs, when you go to exit the BIOS.

  That's all there is to it.

  I can't find your model number to give you the link to the audio driver from the support page and pilot.

  If you have the IDT audio chip, here is the latest driver for it.

  Or let me know what model of audio device you have and I'll see what I can find if not the audio IDT.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102404-1&CC=US&DLC=en&LC=en&os=4063&Product=5182504&sw_lang=

  Paul

• Tecra A7 after updating the Bios is recognized as Satellite M110

  Hello everyone.

  I'm new to this forum, and of course, I need your help.
  after update bios in my tecra a7 202 'Toshiba PC Diagnostic' shows:
  Model name: Satellite M110
  Number: PSBM0U-1234567
  SERIAL NUMBER: 000000000000000000000000000000
  Lower than that, everything is ok.

  I used bios5.10 for both parties. but when I tried to update software panda antivir only has not allowed me to open the winrar exe file.
  There was the vbs script that was dangerous in reviews of panda. I turned off Panda, but it still blocked the exe file. I decided to open the exe with winrar.
  After that, I run SA10Flash.exe. I saved the old bios and loaded a new - but there were 2 ROM files: S10PM510. ROM and S10GM510.ROM. first was younger and I decided to choose it. Maybe it was fake.

  Anyway after update in mode Bios was error with CRT or something like that and choose the option: F2 for configuration and default settings F1 charge. I took F1.
  After that, I have Satellite m110 :(

  Help, please
  Best regards
  Mirek

  Hello

  Sorry, but I don t you understand the procedure.
  Have you read the BIOS update document provided by Toshiba?
  The update of the BIOS is risky If you use a bad BIOS or bad update procedure!

  I checked out the site Toshiba driver and downloaded the BIOS for Tecra A7.
  I unzipped the 510win bios and I found the S10V510.exe file
  It is a file. You need to run!

  To me, it seems you used bad BIOS or bad procedure and therefore the cell displays a false name.

  PS: Don't worry ;) Satellite M110 is also a large notebook: D... just a joke

• HP 15 Notebook G9D64UA #ABA TS: HP Windows 8.1 randomly restarting after updating the BIOS of HP Support Assistant

  Hi, I have a laptop HP Windows 8.1 and I noticed after I did the update to the BIOS of HP Support Assistant, it restarts randomly without any error message.  Is it possible to restore the BIOS if it is a BIOS problem?  The computer works fine but it restarts randomly each time than in quite awhile.

  When you restart the laptop you see error messages?

  You can restore the BIOS to the previous version by using the firmware management option in PC UEFI diagnostics.

  Plug the AC adapter and press the power button.

  Immediately, press the ESC key to call the start menu.

  Now, press the F2 key to enter the diagnosis.

  Choose firmware management.

  In the management of the firmware, you should see the option to restore the BIOS. Select it and let it do its job.