No sound on the TV when connected over HDMI

I have HP G62 laptop. I seem to have lost the audio HDMI when I connect to the TV. Help, please! Have checked the Audio on the control panel and seem to only Realtex Hi Def speakers have implemented.

Hi Tony,.

Download the following installers and Save the in your downloads folder - you can rename each of them for easy identification.

Driver Chipset.

Installer of AMD.

Next, open Device Manager, open sound, video and game controllers, right click on the Realtek HD Audio device and select uninstall - do not delete if requested driver.  Once this done, do the same for the ATI HD Audio device.

Now go to your download folder, click with the right button on the setup of the Chipset and select "run as Administrator" to launch the installation - once this complete, are not reboot the laptop, but right-click on the setup of the AMD and again, do a right click and select "run as Administrator" to launch the installation.

When it finished, restart the computer and let Windows take over completely for a few minutes.

Connecting your laptop to the TV via HDMI, then right click to the speaker icon in the taskbar, select playback devices - hopefully, you should now see an entry for ATI HDMI Output; left-click this time just to highlight and then right-click and select "set as default device".

I hope you now audio through television.

Kind regards

DP - K

Tags: Notebooks

Similar Questions

  • No sound from the tv when connected via a laptop computer vga cable

    I connect my acer to a sanyo hd tv with a vga cable.  pictue is fine, but the sound only comes from my laptop, using windows 7

    Hello

    I suggest you refer to the link mentioned to ensure that Media Center has been configured properly with the TV below:

    Getting started with Windows Media Center

    You may also like to refer to the below mentioned link and check if the cables were connected as they are supposed to be:

    Connect your computer to a TV

    Note: If your computer is connected to a TV, notes that many video cards and cable types do not support audio signals. You may need to connect the sound card of your computer directly to your speakers.

    Kind regards

    Gaurav Prakash - Microsoft Support
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • G6-1b70us Pavilion. Picture but no sound from the tv when you use HDMI. Worked without problem.

    I have a pavilion g6-1b70us I'm trying to connect my TV with an hdmi cable.  I get a picture but no sound.  Previously, this worked without problems.  When I shoot to the top of my reading of the sound settings, the only options are speakers and the headphones.  When I shoot to the top of my devices, the Samsung TV is there, but it is described as a "generic monitor" (thinking it was weird).  I have uninstalled and reinstalled my intel graphics driver and IDC audio driver but still no sound through TV.  Also, I will mention that in sub control panel > sounds and devices there is a link to the SRS Premium Sound technology.  As you can see in the image below, the Samsung device is, but it is greyed out and cannot be selected. Can someone please?

    Well in case anyone is interested I have solved the problem (only took me 12 hours to understand, lol).  Apparently, even if the Samsung TV did not appear in the audio options, you can still right click in the empty box and a toggle option will appear.

  • Microsoft LifeChat LX 3000 stops the sound from the speakers when connected

    Hello

    I bought a USB Microsoft LifeChat LX 3000 headset, and when it is plugged into my USB port, no sound is heard from the speakers.

    When I disconect the speakers rund LX 3000 perfectly.

    Someone knows how to fix this problem, please

    I wanted to check if Microsoft LifeChat LX 3000 has all the entries in this section and if it has settings to enable or disable speakers when it is installed.  It is obviously the installer to work this way by default--I know not how to change the value by default if there is no entry in the audio section.

    Try to download updated drivers for your sound card - she is in the speakers and contolling the LifeChat for an upgrade can provide options that are not currently available and you should be able to control if both can work at the same time.  While you're there, download and reinstall the updated drivers LifeChat as well.

    Here is a link to the Microsoft Support - I don't know if it will be free or not (I can't go past the area enter the product id field). https://support.microsoft.com/oas/default.aspx?gprid=12368&st=1&wfxredirect=1.  If free (I'm not sure I want to pay for support) and then explain the problem and they may be able to tell an easy solution that we have lost.

    Here is a link to the product documentation that can explain what is happening and why.  Maybe it's just the way they are designed to work. http://www.microsoft.com/hardware/documentation/default.aspx?type=LifeChat&sku=JUG-00001.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Video OK but sound does not go to the TV when connected HDMI on HP Mini 311 with XP.

    Video OK, but the sound does not go to the TV when connected HDMI on HP Mini 311 with XP. Has anyone experienced and resloved this issue and can share with me.  The solutiuon provided in the manual does not seem to apply to the Mini 311 model that we use. Help, please.

    James,

    Visit this link,

    How to get his TV using HDMI cables?

  • My computer can not VAT registration and access the internet when connected to the network [secure] through wireless.

    Original title: fix problem 'local only' what is wireless.
     
    -My computer is a HP Pavilion dv5, running windows vista edition Home premium

    -My computer can identify and access the internet when connected to the network through a cable.

    -My computer can identify and access the internet when it is connected to the grace wireless network [without warranty].
    -My computer can't identify [unidentified network] and [room only] internet access when it is connected to the [secure] grace wireless network?
    -Other information systems, identify and access the internet when it is connected to the [secure] grace wireless network.
    -J' confirmed the network, try password works in "safe mode with network", manually configured (TCP/IPv4) using a connected computer.
    S ' Please, I'm desperate and in urgent need of help.

    Hello

    1. If it works well before?

    2 have you made any changes to the computer before the show?

    Method 1:

    You may experience connectivity problems or performance issues when you connect a portable computer that is running Windows Vista or Windows 7 to a wireless access point:
    http://support.Microsoft.com/kb/928152

    Method 2: Uninstall and reinstall the network adapter drivers.

    Follow the steps mentioned.

    (a) click Start, right click on computer.
    (b) click on properties, click on Device Manager
    (c) expand the network card, right-click the wireless adapter option
    (d) click on uninstall
    (e) now go to your computer/wireless device manufacturer's website, download the updated drivers and install them.

    Follow the below mentioned article:
    Updated a hardware driver that is not working properly
    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  • C# examples fail with "Failed to recognize the type of server or the version when connecting to the host"

    I am currently submitting work for P2V conversion from a c# application. I tried to run the application remotely and on-site, but I get this error message (here is the full error):

    "< detail > < InvalidArgumentFault xmlns =" urn: Converter ' xsi: type = "vim25:InvalidArgument" xmlns:vim25 = "urn: vim25" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance" > < vim25:faultCause > < vim25:fault xsi: type = "ConverterNotSupportedConnection" > < hostName > RSMITH < / hostName > < / vim25:fault > < vim25:localizedMessage > impossible to recognize the type of server or the version when connecting to the host "RSMITH". " < / vim25: localizedMessage > < / vim25:faultCause > < / InvalidArgumentFault > < / details >

    RSMITH is the name of the machine with the VCenter Converter Standalone (5.0) and where I wan the VM to go. It's a Windows 7 SP1. I'm under .net 4.0 winform.

    Any suggestions? I'm pretty much run the sample out of the box, except for wrapping a winform around it instead of an application console.

    Cannot you telnet from your Converter machine on the source IDE oucederomsurlesecondport 9089 machine?

  • Can I change the icon of the cursor when hover over one active link with another?

    Can I change the icon of the cursor when hover over one active link with another?

    Muse does not natively support, but all you need to do to make it work is on your page, add properties in the head content:

    Where "value" is the cursor you want for example for a cross-shaped cursor...

  • No sound from the Clip when it is connected to the car charger and car s in the

    I just got a car charger for my 8 GB Clip. I have the Clip connected to the connector of the car aux in, and it plays beautifully this way.

    However, when I connect the car charger, which is a fact by Motorola for a mobile phone, the sound of the Clip completely stops.  There is no sound at all.

    Even if I barely touch the metal of the car charger USB plug to the USB port of the clamp, the sound cuts.

    A ground loop isolator would correct this problem? The comments that I have read of these say all that they helped with motor and alternator noise, but I don't have that.  I have no sound at all, even if the Clip is loaded and he continues to play according to the display of the item.

    I checked the car charger works well because I have a box of jump with a record of 12 VDC (just like in the car).  The cool Clip and plays with a helmet with the Motorola car charger in this configuration very well.

    Any ideas what is wrong and how to fix it?

    Thanks in advance.

    Just for this follow-up, the ground loop isolator completely fixed the problem I had with the sound cutting on my video in the car.

    The one I chose was the PAC SNI-1/3.5 RCA noise filter.  He goes online with 3.5 mm cable to the and has a socket on one end and a plug on the other.  It would have been cool if he had just had two male connectors, because then I could have plugged one side in the Clip and the other in the input of the car Jack.

    There is no significant deterioration in the sound, and now I can load the Clip while listening.

  • No sound from the computer with connected generic speakers VISTA SP2. Symbol pregnant shows active with the Digital Audio device.

    I have vista SP2, I connected to generic stereo speakers using the green light at the back of the computer. Vista does not recognize the speakers. The speaker symbol at the bottom right shows "digital (HDMI) 2 high definition output audio device." It shows active. I had this problem before, and VISTA should pick up 'speakers' something to that effect. I have no sound until it captures "speakers". I can't get VISTA to recognize this. It keeps starting with the digital audio device. Don't know what to do, checked all the forums. It should just pick up these simple generic markets good speakers. Before SP2, I lose sound when VISTA is in standby mode. He would then turn off the stereo speaker and replace the digital output device driver... However since SP2 I can't get VISTA to recognize that I have just connected speakers and not a digital output device.

    Yes, when I uninstalled the driver, THEN shut down the computer and then restarted, he picked up the device high definition audio "speakers" good pilot is NOT the

    "digital (HDMI) 2 high definition audio output device that he used to pick up."

    I now have sound!

    I hope that it stores the right driver now as in the past, when VISTA went into sleep mode, it will disable the speakers, and you have to restart every time.

    Thanks for your help.

    You can add instructions to boumediene, the fact that you must RESTART your computer to search for new drivers, once you uninstall.

  • Satellite U series: Question about bypassing the battery when connected on AC

    Hi, I am a bit newbie to PC Toshiba laptop (series U) and I was wondering if my laptop has this feature where it bypasses the battery when it is fully charged and the power supply cable is connected?
    I see the battery blue led is on even when it is fully charged and the power is connected, it means that my computer is still using the battery?

    I'm running a lot and I will not waste my battery life.
    Thanks for any comments.

    Hello

    Congratulations on your new machine, I understand that worried you´re for your battery life. I was scared too, but a lot of people here in the forum told me that, in each new machine for many years (i.e. about 6 to 9 years) almost every laptop has an electronic charge that regulates the process of charge of the battery.

    Don t worry, if your battery is fully charged, the built-in charging circuit is a special State that is as "cool cool" to maintain your battery and to protect the battery.
    S better to keep the battery in the machine then removing it.

    Welcome them

  • Satellite A500 - Remove the battery when connected to the network?

    Hello

    I bought a new Satellite 500 and I would use it as much as possible. I'm not sure the stage of development of this battery. Should I remove the battery when I use the laptop at all times with the net supply?
    Or this does not damage the battery longer years yet there is, or is the problem of the destruction of the battery because of the heat and being reloaded frequently persists?

    I'm sorry if I could post to redundantly, but it is difficult to search for information, since I'm not a native speaker.
    I encourage you just for a small tip for a related thread if available.

    Thank you very much!

    Hello

    To be honest, I often work with connected AC/DC adapter, but I never removed my battery. Sometimes I decide to work in another room and then I just unplug the AC adapter and that s all the! :)

    Furthermore, I founded this interesting link for you:
    http://APS2.toshiba-tro.de/KB0/HTD9401AZ0001R01.htm

  • No sound from the headset when using hdmi

    I use the HDMI for a big screen, but with this use, the headphone is turned off. I need to be able to use the HDMI for the monitor and the headphone jack for sound.

    If you have no sound with the plug HDMI is connected, it means that your current sound settings are set for audio must be set to the HDMI output. Go to sound settings and pass parameters of HDMI output for speakers.

    Open Sound by clicking on the Start button, and then click Control Panel. In the search box, type sound, and then click sound

    In the Audio window, select the playback tab
    Replace the default value with the green mark check speakers with HDMI connected.

  • I can't get sound through tv when connected via HDMI

    I have a HDX 18 and I connected it to my Olevia via the HDMI. I hear no sound on the tv. I used to be able to. What settings should I and how >

    Hey you probably already found a solution to your problem because you posted this comment a long time ago. But incase you don't have. Here's the answer to your problem. I hope it helps.

    1. So that the audio works fine on HDTV, the device must be configured as peripheral by default in the computer Device Manager. To do:
      1. In Windows® XP:
        1. Note! Before you configure the audio device by default, the following Microsoft driver must first be installed: Universal Audio Architecture (UAA) High Definition Audio class driver
        2. After installing the UAA driver, click Start
        3. Select Control Panel
        4. Select sounds, speech and Audio devices
        5. Select sounds and Audio devices
        6. Click the Audio tab
        7. In the first article entitled audio playback, select the device you want to audio out of
        8. Click OK to save your settings
      2. In Windows Vista®:
        1. Right click on the "speaker" icon
        2. Select the device of reading options
        3. Right click on the device you want the audio to the output of
        4. Set as audio device as the default
        5. Click OK to save your settings
      3. In Windows® 7®:
        1. Go to the Start button
        2. Select Control Panel
        3. Select the material and audio
        4. Select sound
        5. Click the Read tab
        6. Select the device you want to audio out of
        7. Click on set as default
        8. Click OK to save your settings

  • Cannot hear the sound of the TV after connecting via a HDMI cable

    Original title: sound on tv

    I was able to hook the hdmi cable to the computer laptop & tv and watch movies on tv. Now, for some reason I can't hear the sound on the tv more, the sound from the laptop only.  How can I fix?

    Hello Monica,.

    -What operating system is installed on the computer?

    If you have installed Windows 7, you can read these articles and check if that helps.

    Connect your computer to a TV: http://windows.microsoft.com/en-us/windows7/connect-your-computer-to-a-tv

    Sound cards: frequently asked questions: http://windows.microsoft.com/en-us/windows7/sound-cards-frequently-asked-questions

    Thank you.

Maybe you are looking for

  • File through Internet Explorer problem

    A few days ago, a new file appeared on my computer, it must be some kind of scam because it's something that I'm not subscribed to a Bill. I tried to remove it, but every time I turn the computer back on the next day and connect to internet it return

  • Laptop HP - 17 t - x 000 c: health check

    The health diagnosis check doesn't seem to be on my system. Can I download it? Is this necessary? Thanks for any help or suggestion.

  • To burn music from media player, how do I?

    Original title: CD burner/computer downloaded media player/caint burn. Have Dumbell CDburner, to burn music from media player. Help!

  • How can I delete a single contact of a recurring meeting?

    Hey all,. I created a meeting every Tuesday at 15:00 for a lot of members of my team. A member is now on a different team, but continues to receive emails. Without canceling the meeting, how can I remove just him as a contact for the express outlook

  • maps of memory in the mail - protection?

    I intend to use a lot of chips so that on vacation outside the United States and might send cards to home care.  What protection should I use 99.9% certain that a chip will recover at home with all the data intact and ready to download?  I expect to