No WiFi on S10e after bios update

Similar Questions

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• Is my computer better after BIOS update?

  Dear Sir.
  I have the idea that my tecra M2 works better after upgrading the bios (from 1.3---> 1.5): sometimes I had the problem that wifi has not begun well, the fan was too often running: after the upgrade of these things worked much better!
  Some people have the same experience?
  Thanks in advance
  Dr. weekx reg

  Hi Reg,

  It is quite possible that you will see some 'differences' in the behavior patterns of your laptop after BIOS upgrade to a later version. Each new version of a BIOS can contain corrections or adjustments to the previous ones and values parameters and can even contain new features. Unfortunately, the new version of the BIOS can also contain changes that may negatively affect the system or make it less compatible with the old facilities and devices.

  I generally adopts the principle that the BIOS should be updated if a specific problem is currently experienced in the hope that the latest version of the BIOS can be beneficial.

  I am pleased that your update has worked well for you on this occasion.

  Best wishes

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Portege M800 no boot after BIOS update

  Hello

  I encountered some problems with my netbook (Portege M800-10W) after the BIOS update.
  The update of the BIOS program appears failed. Then my Netbook automatically rebooted and now I can't start my PC more.
  All the LEDs will light up but the screen remains black and after a few minutes, the beep 3 times (1 long, 2 cm) netbook.

  How do I restore the BIOS to the previous version (or plant)?

  Thank you.

  Adrien

  null

  Hi Adrien

  I think that Akuma is right. Your laptop must be verified by the service of Toshiba s. Let check your laptop and I hope they will help you with this.

• Satellite L750 - Bluetooth does not work after BIOS update

  I am preparing some L750 notebooks for use and accept updates from the Toshiba, which included an upgrade of BIOS v1.70 for v2.00. He appears after this update occurs that Bluetooth no longer works, i.e. try to install Bluetooth Toshiba stack will fail as it is said that the Bluetooth radio is disabled and must be turned on for continue.

  As the L750 (model PSK1WA-0C300R) is not a hardware switch to enable or disable the Bluetooth/Wi-Fi, the only option available (Fn + F8) is unsuccessful. I ran a recovery of factory default installation and Bluetooth still does not - resumption of classes does not restore the BIOS to the previous version. I have 5 of the model and confirmed the update of the BIOS is the cause. Two laptops now have v2.00 and Bluetooth has been tested in the work before the update of the BIOS.

  If Bluetooth is not critical for the environment which I deploy these notebooks, it's an annoyance I want to solve. My questions are: has anyone encounter the same problem and managed to resolve it? Is there a BIOS v1.70 available for download to restore the functionality? Y at - it an update of the BIOS > V2.00 for solve the problem I have? Thank you.

  Hi JasonL750,

  Load default settings after updating the BIOS? Go into the BIOS, press the F9 key to load the default settings of the installation. Also, make sure that Bluetooth is enabled in the BIOS if there is such an option.

  In addition, it would be interesting to know what happens if you use the FN + F8 key combination. Don't you see that he has an option to turn on Bluetooth and if so what happens if you do this?

• Satellite C55-A-16Z - graphics card does not work after BIOS update

  Hello

  I have a portable Satellite C55-A-16Z with windows 8 and a Nvidia geforce 740M graphics card.

  Last week he asked me to update the version of the bios at 1.30.
  The bios update was successful.

  However when I restarted my laptop I started having a BSOD dgxkrnl.sys.
  Correction of the error and restarted for an another BSOD Windows, and after the second solution, I stopped making BSOD.
  But now, I noticed its games running, if not use the dedicated card, but use the 4000 Intel.

  In the settings Nvidia dedicated card is configured to be always on.
  It seems that my card is missing, but it appears in Device Manager.
  I tried to delete, update the drivers and the default factory reset, but nothing helped.

  Also, when I go into Options power the Intel card is listed and when I disable the card intel in the Device Manager it starts to use the graphic viewer for windows.

  How can I get my Nvidia card to work again?
  Any help is appreciated.

  Thanks in advance.

  Hello

  After the BIOS update the BIOS should be set to default settings.
  You can do it in the BIOS.

  In addition, you mentioned that Windows 8 is still installed on your laptop.
  8.1 to win has already been published by Microsoft and I highly recommend that update you the system of 8 to 8.1 Win Win.

  Before you start the upgrade to 8.1 win, you should check and read the instructions step by step for Toshiba: http://www.toshiba.eu/innovation/generic/windows8_1-message/

  I guess that after the Win 8.1, nVidia graphics card upgrade works well also.

  Your comments would be greatly appreciated.

• Satellite C650 - black screen after BIOS update

  My Satellite C650 Windows 7 - won't start afte BIOS update / switch.

  Everything worked very well until the automatic update of Toshiba asked me to download and install the new BIOS update, I did. At the same session Windows and McAfee asked updated. I agreed to all. After all updates have been installed, turns off. The next day when I walk, I see only black screen. I also tried F2, F12 and drive recovery. Nothing happens!

  Any recommendation?

  Hey,.

  It seems that something was wrong during the update of the BIOS and so that you can t the computer unbootable. But I put t understand why you did the BIOS update. If everything works correctly, you can forget about this update. More if you do a BIOS update you shouldn't t run any other updates or programs that might affect the update of the BIOS.

  Anyway, in this case you can do nothing and you need professional help. Please contact an authorized service provider and guys can help you update the ROM module On the Web from Toshiba site, you can find a list of all the FSA:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Satellite Pro A300 - touchpad failed after BIOS update

  After that good BIOS update 2.00 to 2.10 / suggest by ALERT TEMPRO - http://support1.toshiba-tro.de/tedd-files2/0/bios-20091125132031.zip/ the touchpad of my Satellite Pro A300 - GR 1 stopped working.
  He appears under the name hidden in Device Manager. The State of the device - "this device is not present, is not working properly or is not all its drivers installed." (Code 24) "reinstall the driver has no effect of course. I can also access the BIOS utility when you start pressing F2.
  Running Vista Business 32-bit Edition.
  Ideas to solve the problem will be highly appreciated!

  Hello

  Normally, it should be possible access the BIOS, if you press F2, once you have turned on the laptop. Please check again and load the default settings there.
  And you cannot access the BIOS if you shut down the computer.

  You can use an external mouse on the laptop? Please check this too.

  I've also updated the BIOS on my Satellite A300 but I n t have a problem with the touchpad after the update.

• Satellite M100 - no speakers sound thorugh after BIOS update

  Hi all

  I have satelite M100 PSMAAA-02006 with XP. I just updated the Bios on V3.0. Speakers do not work after update but the audio jack works so with headphones I can listen to but not through Laptop speakers and the keys to media on top of keyboard play, pause, stop, next, back, etc. homepage react too much.

  Someone knows the solution to this issue. Or is it possible to get the old BIOS? Although I not sure aboutt previous version.

  need quick help. Please answer as soon as possible.

  Thanks & best regards...

  Hi Julie,.

  I doubt that this was due the update of the BIOS. Is that what you have loaded default settings after updating the BIOS?
  Have you chosen the correct BIOS update?

  Normally you can hear the sound on the speakers laptop if you disconnect the headset. Make sure that the sound is not muted, you can do this with the FN + ESC key combination.

  About the multimedia keys, I would recommend reinstallation of Toshiba common Modules. You can find it on the Toshiba site.

• Laptop HP OMEN - 15-5010nr: Omen HP 15: backlit keyboard does not not after BIOS update

  This morning my HP omen arrived by mail, fully functional with everything in tact. After I left my laptop to install the updates from HP Support Assistant (one of these being an update of the BIOS updates), I returned to find my computer restarted and my enlightened retro keyboard does not. After trying to use HP OMEN control to fix the keyboard, I found the keyboard flashes when I click "Apply to all Zones", but then immediately turns off again. Is it possible to fix this keyboard backlit ir question can we see an update in the near future that resolves this problem?

  Found a solution! Apparently, the keyboard stops after the update of the BIOS, so to reactivate just push F5.

• Re: Satellite - blue screen after BIOS update

  Hello

  My computer laptop girls worked very well until I did the BIOS update this morning. Now, I get the blue screen of death STOP: 0X0000007F. Help, please

  concerning

  Carol

  Hey, Carol, welcome to the forum! :)

  Don t misunderstand me, but may I ask why you n t post more information about your problem?
  Important to know is that your laptop you have exactly and where to download the updated BIOS and for what model. This is important information.

  By the way: have you ever tried to load the default settings in the BIOS after update?

• PAVILION NOTEBOOK 15 K7Q21EA #: SCROLLING WINDOWS PROBLEM AFTER BIOS UPDATED 10 (08/03/2016) PAVILION 15 YESTERDAY 16/10/2016

  CANNOT CONTROL THE SCROLLING. CURSOR DOWN TO THE LOW WHAT MAKES IMPOSSIBLE TO SAVE TO A FOLDER

  Hi @STICKMAN5124,

  Nice day! Thank you for your participation in the Forums of HP Support! It is a great location to get resolutions and interact with experts from the community. It will be a pleasure to help you.

  I saw the post and understand that after only a bios updated cursor drops down due to a problem of scrolling.

  Impressive work, do the update of the bios. Kudos to you for this. It is a privilege to work with tech-savvy and technically competent customers like you and we greatly appreciate your business with HP. You have been great to work with.

  Please check in F2 diagnostics if the scrollbar works correctly. If Yes, then you can update the chipset drivers and http://hp.com/drivers touchpad drivers you can also consult with a mouse external further isolate the issue.

  You can also run diagnostics on the touchpad from this link by going to the UEFI F2 diagnostics: http://support.hp.com/in-en/document/c03467259 please run the complete components. If any component fails, please note the failure code. This is done to determine if the problem is hardware or software partners.

  If it passes and scrolling works very well, please perform these updates. If you are still having the same problem on page F2 UEFI (screen) then you could roll back bios after performing a hard reset. Link for the hard reset: http://support.hp.com/us-en/document/c01684768

  • Please perform this step to roll back bios.  Hold down the "Windows" key and the letter "B" at the same time, then press the power also button for about 5 seconds at the same time.

  I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well.

  Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Satellite A135-S2286 - USB ports does not work after BIOS update

  I recently had the dreaded BIOS password prompt problem. I checked online to the toshiba support site and took the laptop to a toshiba authorized service center and is fixed by getting the updated BIOS updated to 1.60, but after update BIOS, none of my USB ports work.

  When I connect a USB device, a warning from yellow pop up comes up unrecognized USB device. The same USB device works fine on other computers/laptops. I searched online for a solution and found on a lot of people have the same problem, but did not find any fix for this error.

  It will be useful, if someone has a solution for this error.

  Hey Buddy,

  Is there yellow exclamation marks in Device Manager next to USB ports or they appear correctly?

  If you notice a yellow exclamation you must remove the USB port and restart the computer. All USB ports are installed automatically, you do not need an additional driver.

  I hope that it helps :)