Non-System Disk, press any key

Hi, what it isi have a ST3500320AS. I was on the web site of Seagate and downloaded this ms-sd1autitity that checks the updates of your player. When he starts an application needs to open, but it does not work. What happens now, the Dell splash screen appears, the next screen said, "Non-System Disk, press any key". Well, I do this and the system boots. How can I get rid of this message disk not system. PS I used this "Download SD1A Firmware Update utility". Thank you

Hi ejn63, yes my BIOS still sees the 2 hard drives. Hard drive 1 is Vista and Win 7 RC and drive 2 is, Win XP and a data partition. When I go to the messagec to press a key, it starts normally in my boot options, which gives me the ability to start in Win 7, Win Vista or Win XP.

Tags: Dell Drives

Similar Questions

  • Non-system disk press any key to continue

    About 3 or 4 times a week, my screen is black and says "press any key to nonsystem disk continues." When I press a key, the same sentence is repeated. And he repeats as many times as I press a key.

    I don't know why it does this or what it means or how to fix it. Ideas? thoughts? suggestions?

    Go to your Bios/Setup, or the Boot Menu at startup and make sure that the boot order is for the HD player to be 1st in the boot order.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

    You can have Boot USB active 1st in the boot order.

    See you soon.

    Mick Murphy - Microsoft partner

  • Nonsystem disk, press any key

    When I turn on the laptop, he said Non-disque non-system, press any key. So I press a button and it says MBR error 1 press any key to boot from floppy.

    I can't find my restore CD. I installed on my laptop of Acronis but do not know if this will help.

    Please help me.

    Hello

    First of all I would like to know what model phone you have and what Windows system do you use?

    Regarding the question:
    It seems that you have a master boot record error. This means that preinstalled system is too bad and therefore he cannot be started
    It is possible that the partition on the HARD drive is confusing upward too

    But the fact is that you have need of a system disk or recovery in the repair of the order or to install the system again without these drives, you wouldn't be able to get the laptop running using Microsoft Windows disk, you can try to repair the MBR.

    But the Toshiba Recovery cannot be used to repair the system, you can use the recovery disk to reinstall the image

  • Satellite 1800-921: error - Insert System Disk in Drive, Press Any Key when Ready

    Hello
    I bought a satellite 1800-921
    He had no disc driver/OS with the operating system that was on laptop was errors.
    So I decided to install my own copy of win xp pro.

    After installation and 1st reloads everything seemed ok, but now whenever I switch on the laptop it just displays

    Insert system disk in drive
    Press any key when ready

    I tried a win 98 disk but always appears with this error
    any help would be greatly appreciated
    Thanks in advance
    Cheech Chong

    Hello

    Seems that the laptop can not find the bootable source.
    This means that the HARD drive is malfunctioning or the boot sector is defective.

    By the way; have you tried to change the boot order in the BIOS?

  • Pavilion dv6 - 7095ca: no boot device - insert boot disk and press any key


    Thanks for your help and please excuse my bad English.
    Please check item 7, if you're in a hurry. This is the point with my Pavilion DV6 - 7095-CA:

    (1) the operating system is Windows 7 Home Premium (64 bit), the provided original with my 7095CA Pavilion, more updates HP until 2013, and all Windows updates until July 2015.

    (2) now I can't access the operating system and I have no interface UEFI. I can see that I press F2 at startup, just a test simple disk in BIOS f.0Une (the test shows that the disc is OK)

    (3) return in 2013 it took a drive failure. I did replace the disk and reinstall original Win7, all updates, including the HPS, win7 updates and all my personal software.

    (4) at this time, I bought a spare hard drive and did a complete copy of the disc using Partition Wizard bootable cd. The second disc has been tested and worked perfectly, with all of my personal software on this subject.

    So I have 2 HDs identical with the same system on both drives, fully working and tested.

    (5) a few days ago I came across the HP website and made a few updates, including the BIOS f.0Une (the last BIOS update, was of course).

    (6) after BIOS update ran, I received the message "no boot device - insert boot disk and press any key".

    (7) I couldn't solve the problem, so I did remove the hard drive and install my backup drive, which lay in a dry place without danger from 2013.

    (8) I turned on the computer and got the same message "No boot device - insert boot disk and press any key", and I couldn't find any way to solve this problem.

    Now I'm doing a new installation on a third HD everything works very well, so far, in the new facility and I will never buy HP again.

  • G72 Pavilion. : no boot device. Insert the disk and press any key

    My hard drive died recently. I installed a new. Now I'm gettig no boot device - insert boot disk and press any key. What should I do to fix this?

    Hello

    If you find your recovery DVD, you can use them to reinstall the operating system on the new drive - this is described in the document of HP here.

    If you do not, you can order a replacement set by starting at the link below-, the cost can vary a bit depending on where you live, but they are generally inexpensive.

    Order HP recovery disks.

    If you have a problem with this link, try to order them directly from HP.

    If you live in the United States, contact HP here.

    If you are in another part of the world, begin here.

    Kind regards

    DP - K

  • Press any key to put an end to an exe BACKS run in system.exe VI

    Hi I am running some old programs exe based BACK.  Two programs that run one after the other, loop and redo (variables are modified for each loop) the first exe program requires the user to "press any key" to put an end (close window CMD.  When I start my VI using the sub - VI system.exe to run DOS programs I have to "Press any key" to close the window and leave my VI to continue a loop.  Or if I use the option 'Until the end', I find myself with a bunch of Windows CMD to close at the end.  There must be a simple way to "simulate a key shot" Plan B is to train a monkey to sit in front of the key board...

    I using Labview 2013 under windows XP / 7

    Thank you

    Check out this post.  If this does not work for you, you can try to use SendKey in a Powershell script.  Good luck.

    Full disclosure, I did none of these, can't vouch for their usefulness.

  • Is "PXE - MOF: PXE ROM. exit" then below I don't get, "No Bootable Device - Insert Boot Disk and press any key any" why?

    I bought the lifetime windows, defender security system, I also downloaded the windows repair and ran it, I even cleaned my c drive and defragmented, but I always get the same black screen. This is what it looks like.

    PXE - MOF: Exit PXE ROM.

    No boot device - insert boot disk and press any key

    /} In this area here, I slash turns clockwise

    Does anyone know how planned it and most importantly, how to prevent?

    Try to change your startup settings for...

    1 CD-ROM
    2 USB
    3. HARD DRIVE
    4. (if available) floppy drive
    5 LAN.
    You can change it by pressing the button shown next to "Boot Order"
  • Windows 7 when I turn the laptop it says check cable connection pxe - mof: outgoing intel pxe rom no boot device insert boot disk and press any key

    Windows 7 when I turn the laptop it says check cable connection pxe - mof: outgoing intel pxe rom no boot device insert boot disk and press any key

    Hello

     

    1. What is the brand and model of the laptop?

    2 have you made any changes to the computer before the show?

     

    Method 1:  Change the boot order in the BIOS settings:

    See the following steps:

    Important: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    (a) start on typing Dungeon either F1, F2, F10, Esc, or DEL to enter the BIOS Setup.

    Warning: some manufacturers use F10 for recovery of the system.

    (b) glance to "Drive Configuration", "Boot order" or similar

    (c) check the second drive the first boot device CD/DVD and hard drive.

    (d) to save the settings and exit.

     

    Method 2:

    Step 1: Trying to boot into safe mode and see if that helps.

    Start your computer in safe mode:

    http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

    If step 1 work, try step 2

    Step 2:  A clean boot to check if startup item or services to third-party application is causing this issue.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:

    http://support.Microsoft.com/kb/929135

    Note: when you're done to diagnose, follow step 7 in the article to start on normal startup.

  • How to fix error of bootcamp: no boot device - insert boot disk and press any key

    When I try to install windows using bootcamp No. bootable device - insert boot disk and press any key any that appears at the start of the installation of windows 10. any solution please.

    Thank you

    What is the year/model of your Mac?

  • Try to install Windows 7 via USB, El Capitan, Macbook Pro 2011 but get this error "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

    I am trying to install Windows 7 via USB, (El Capitan, Macbook Pro - early 2011), but this mistake "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

    You cannot use a USB on Mac 2011 Installer. Please burn the ISO on a physical DVD Windows (a DVD - R Carbon SL on the rate of burning slower is better) and use it to install Windows. The file Info.plist changes only allowing the creation of USB, but does not fully support a USB Installation.

  • Satellite L300D-222: "insert the boot disk and press any key".

    Hello

    My laptop froze this morning and so I stopped it when restarting it however, I received the message "No boot device - insert boot disk and press any key", what it means?

    I didn't not get discs with the laptop, or have I made the recovery discs. The instruction manual says to press f8 when I restart and go to "menu of advanced start", but it doesn't matter. Where should I go from here, is there a program I can download that would have this disc? All my work on the computer will be lost?

    Thanks in advance for any help!

    Hello

    He looks at the HARD drive died and so the laptop can not boot from the HARD drive but request disk bootable.
    But to be sure, you need to access the BIOS (press F2) and check if the HARD drive is recognized in the BIOS.
    If it s not recognized, then you need a new HARD drive.

    The recovery disc can be ordered here:
    https://backupmedia.Toshiba.EU/landing.aspx

    Good bye

  • Lenovo series k - disk error - press any key

    I have a brand new Lenovo computer. Its a center of the idea, and when I start it it says disk error - press any key. If someone has had this problem and to know what anyone on this subject? I work when I press "any key" but I'm worried that it could turn into a serious problem. Its only 2 days years the computer.

    Moderator edit: added detail to the subject.

    Oh never mind lenovo was trying to read my USB. Apparently you can not leave a flash drive in Lenovo you can HP. otherwise, I love this computer!

  • I screwed up trying to install windows on my computer 10 and I XE off installer and now its says "no boot device - insert boot disk and press any key".

    I was just trying to download 10 on my computer windows using boot camp assistant. I answered the questions for windows when you need to respond as what kind of language you use and then I messed up on one of the questions. I didn't know how to go back so I just pressed the red x. When I did that he must get off my computer and when it's done I got a black screen and then it says "No boot device - insert boot disk and press any key" I don't know what he meant by no bootable disk and I was hoping that you guys can help me fix.

    If stop you your Mac and your power it back up and hold down the Alt/Option key, you see a Windows selection? If so try to select and see if the installation will continue.

  • No boot device - insert boot disk and press any key

    Hello

    I was with boot camp to install 10 Windows from a usb key. The first problem I encountered was an error message stating that Windows supports software could not be downloaded on my flash drive. I read that the necessary drivers could be installed later so I unchecked the box. The part of the installation, then training camp as it should (create a partition etc.)

    However, when the Mac went to restart and (probably) to start the program installation of Windows, the error message "No boot device - insert boot disk and press any key" displayed. My problem is the wireless keyboard does not respond and the light on this issue seems to suggest that it is not connected. My guess is that the drivers needed, such as Bluetooth are not there.

    I'd be happy enough to restart OS x and forget all about Windows, but I can't see how to get around this problem?

    A wired keyboard could work?

    any help is appreciated!

    Thanks in advance

    Max.

    A wired keyboard and mouse will work. If you try to install Windows and tried to download the Windows software on a wireless network, try a wired connection. to rebuild your USB Installer.

Maybe you are looking for