NOR-MAX 5: analysis of the instruments?

Similar Questions

• With the help of NOR-5641R with FPGA and the instrument driver

  
  

  Hi Ran,

  I don't think what you describe is possible for two reasons.

  1. You cannot run the pilot bitfile instrument at the same time as a user defined FPGA bit file
  
  
  2. AO ports are AC coupled, so you will not be able to generate a DC bias on them.

• Attributes in NOR-Max not found in Labview

  I'm currently developing a LabView tool (2011) with a camera from Manta G504B Ethernet. It is NOR-compatible IMAQdx but in NOR-MAX attributes are not the same as those found in LabView. I would like as my tool developed to be able to change the exposure and acquire values and lifestyles. However, these attributes do not appear in LabView but appear in NOR-MAX. is it possible to get these attributes in LabView, since these values will change very frequently?

  My Manta firmware is 00.01.44.00

  NOR-IMAQ is 4.6.1

  E/s-OR-IMAQ is 2.5

  NOR-IMAQdx 3.8.1

  NOR-MAX 5.0.0f1

  Answer was found with the example OR grab and Attributes.vi base.

• Lost the remote TCP/IP connection through NOR-MAX

  "" Hi, I try remotely LeCroy WaveRunner 104Xi oscilloscope through "resources VISA TCP/IP" option in Control Panel OR MAX, but the VISA session is lost (0xBFFF00A6) right after I viWrite the '* IDN?" order several times.

  Here's my full configuration process:
  1. install the Passport VISA LeCroyVICPPassportInstaller_1.0.8.exe , LeCroy oscilloscope

  2. setting of the session to follow the instructions (as per joint, LAB_WM827.pdf)

  [by the way, I'm not able to configure the session as "VCIP:'type', I only be able to configure the session asTCPIP0:: 1861:OCKET" ""]
     
      TCP/IP resources VISA-> Create TCP/IP new resource...-> Raw Socket
     Set the IP address: 137.57.96.8 (this IP address is successful to be ping by PC and this address is of course belong to the 104Xi WaveRunner oscilloscope)
  Set the port number: 1861

  3. then, there will be a new resource under "resources VISA TCP/IP". Select this option and 'VISA Open Session'. A dialog box will be retractable to the communication of the instrument.

  4. go to the tab "viSetAttribute", the value VI_ATTR_TCP_KEEPALIVE to VI_TRUE, VI_ATTR_TMO_VALUE the value of 15000.

  * NOR-MAX Version: 3.1.1.3004
  * Connection: The ethernet cable is used through the server (No 1 to 1 connection) of the company,

  "After all this, I send '* IDN? \n"(dans l'onglet viWrite ), it returns the value 0 (which means no error occur) and return 6 counts. " So I try to read a buffer (in the viRead tab), but it send me error timeout (VI_ERROR_TMO). After that, I erase the buffer in viClear. Then, I repeat same steps, this time he (viRead) return me connection lost error (VI_ERROR_CONN_LOST).

  This situation is repeated every time that I reopen it new session. In the meantime, I also doubt that the viWrite did send the command to the oscilloscope or not. The oscilloscope was no response after that I have send "ASET" (WaveRunner 104Xi order for autosetup oscilloscope) through the viWrite tab.

  I am out of ideas now.

  What's my configuration OR-MAX problem? or hardware problem? or a server problem?

  Please advice... need help badly.

  Thanks in advance.

  Hi wcsoh,

  Alan and LeCroy Support here...

  Use the type of connection (LXI).  The problem is that when you use the connection TCP/IP (ACIP) type, you cannot configure the WaveRunner 104MXi as a resource of VISA's TCP/IP in MAX.   Note that MAX is not 'hip' to recognize any instrument type TCPIP, including extended via ACIP LeCroy.  To use LXI, go to utilities > utility configuration... and then to the 'Remote' tab, where you will find the button on the left side of the screen of config to use 'LXI '.  If you don't see this button, you will probably need to update your firmware.

  With the type of connection (LXI), you can automatically find the scope through MAX, enter this amount as a VISA TCP/IP resource and configure an alias as well...  You can also point your web browser to the IP address of the bezel, and you will see a status page with information, including the name VISA always useful resource to use when you configure the scope in MAX.  (Note, however, there is no need to use MAX at all when the connections of VISA to LeCroy oscillloscopes!)

  Here is a link to an application note written by me which deals with the LXI interface, including information about the configuration of MAX to show scope: http://www.lecroy.com/tm/library/AppNotes/LXI/LXI_Interfacing_AppNote.pdf

  Do not hesitate to contact me for any question!

  Best regards

  Alan Blankman

• FireWire Camera disappeared to MAX when you select the driver NOR-IMAQdx

  Hi, as the title suggests, I'm having a problem getting my camera firewire (a PixeLINK PL-A742) appears in MAX so I can use it in my application. First of all, a bit of history.

  It was all works fine on an old computer (Windows XP SP3, LabVIEW 8.6.1, NOR-IMAQdx 3.2).

  We just received two new computers. They have Windows 7 Professional 64 - bit installed on them, then we are stuck using that (I was going to install labview in XP Mode, but there is no support for firewire, which no longer works). After finally getting installed labview (to run the setup.exe from Distributions\LabVIEW-ENG\LabVIEW861\, rather than make the autorun) we cannot get this camera to work. It works very well with the PixeLINK pilot (and Capture OEM program that accompanies it).

  So here is what I tried, and what happens when I do.

  (1) install cost of LabVIEW (including IMAQdx 3.2) and PixeLINK drivers.

  (2) at this stage, the camera works very well in the PixeLINK application

  (3) start MAX. It detects the camera and shows under devices NOR-IMAQdx. When you click on the camera, it informs me that the selected device is not currently associated with legacy OR-IMAQ driver IEEE or the driver OR-IMAQdx. This is perfect, it is supposed to do.

  4) click camera > driver > choose NOR-IMAQdx IIDC camera digital

  (5) he then disappears from MAX (no record OR-peripheral IMAQdx more). If I goto windows Device Manager, it comes under National Instruments IMAQ Interfaces as NOR-IMAQdx IIDC camera, says the pilot did get properly, it just does not appear in MAX more...

  (6) at this point, there is nothing I can do to get it back to the MAX (except in Device Manager to switch the driver on the PixeLINK one, then he pops up and we return to step 3)

  So, any ideas? This could be a problem with firewire interface and not the camera? I use the FireWire on my computer. It presents itself as Texas Instruments 1394 OHCI compatible host controller in Device Manager.

  Here are a few screenshots to help illustrate my problems.

  It is the initial configuration using the PixeLINK driver.

  

  It's MAX with the PixeLINK driver

  

  As soon as I click on the NOR-IMAQdx IIDC camera, it disappears

  

  And here's what it looks like in Device Manager after you have selected the NOR-IMAQdx driver

  

  Anyone have any ideas? I'm open to anything. At this point, I'm completely at a loss to know what to do.

  Thanks in advance,

  Devin

  Mechanical engineering intern

  University of Victoria

  Well, you can just ignore this message now. I solved my problem. I installed Vision Acquisition software 2009 and it seems to have solved my problem.

• My NOR cDAQ-9191 is over the display of the module installed in MAX.

  I just bought a 9191 cDAQ chassis with the NI 9219 AI module.  MAX initially showed the long-9191 9219 under network devices.  However, after several hours of messing around with the wireless settings and by pressing the reset button several times, MAX no longer displays the 9219.  Nothing dramatic happened to the hardware (that is, it was not dropped or mishandling), so I suspect a problem of self-inflicted free software.  The technician OR I have recommended 'Reset Configuration data' Max, I did, but that didn't fix it.  Has anyone else had this kind of problem?  Any suggestions?

  problem solved... several network services OR were stopped.  The module will appear once I restarted the service.

• OR Max: No button "Scan for instruments.

  Before I start I will say that I used the NI GPIB-USB-HS devices for years with relatively few questions. I also visited several forums posted by people with a similar problem.  Basically, my problem is as the title suggests: when I open OR max and look for the GPIB-USB-HS device there is no button "scan for instruments" I'm used to seeing on the top bar.

  It's the first time I used nor max v. 16.0 and it is quite frustrating.  I believe that my ni488 driver is up to date and I have included all the details of the pilot in the screenshot below.  I can't understand what's not here, but my program LabView can not connect the GPIB instrument.

  A couple more things to note:

  -The same GPIB-USB-HS device that doesn't work here works on another computer with an earlier version of NI Max.

  -LabView program that I use to connect the GPIB instrument which does not work here works on another computer

  -When I browse for the GPIB-USB-HS in 'Device Manager' and select 'set to day pilot' windows tells me that the driver is up-to-date

  -I'm on windows 8
  

  Please help me.

  Hi JohnDoe89,

  This sounds like it would be very frustrating to meet - so let's see if we can reduce what could be the cause of the problem, we can determine the best way to solve it.

  You mentioned that things work correctly on another computer with software versions different-can you let us know which are running the versions of the software on this computer? It would be useful to compare to the list in the picture you posted.

  In the list you posted (I guess it's the software on the computer that does not work, rather than one that is), I noticed that you use 16.0 versions of many of your drivers. The readme for 488,2 drivers, it looks like the version 16.0 is backward compatible with LabVIEW 2013, rather than the 2012 I see on your list. If this computer is running an earlier version of the drivers/MAX, but the same version of LabVIEW, it's perhaps at least a part of what is causing the problem.

  If you can put the list of software for computer work, which will give us more information to work from.

• NOR-MAX for VISA DURATION 4.2

  Hello

  I posted this on the Narcotics Control Instrument, but maybe it's not in the right place since I didn't get all the answers. Here's my question:

  I have been looking for more than an hour and have not led to what. Is there a version of the NOT-MAX runtime? I have deployed executables LabVIEW on many other PCs and I encounter a problem on one of them where the resource VISA vi does not return the exact list of the COM ports even as drop-down list of the vi box VISA set up a Serial Port. For example, the list box might show COM1 and COM4 COM10, but VISA resource find vi shows ASRL1::INSTR, ASRL4::INSTR, and ASRL12::INSTR (should be ASRL10::INSTR). So I need a program such as NOR-MAX to change the alias on the PC with the execution of VISA 4.2 engine so that it corresponds to what shows the VISA configure Serial Port vi, incidentially, that matches what is shown in Device Manager.

  The PC in question does NOT the LabVIEW development environment installed, so it has NEITHER-MAX. is there a stand-alone exe OR-MAX I can install it on other PCs without the IDE LV? Manual change of visaconf.ini will do the trick? If so, is that what I should remove all aliases, uninstall all external (VCP) ports in the Device Manager, restart the PC (or not) and start again, reconnect the devices?

  Thank you for any help or advice.

  Ed

  James,

  Thank you for your response. Yes, I use the Application Builder and no, I chose not install NOR-MAX, but I see there in my file of project under "additional installers. I will consult the installer to run from the Web site of NOR.

  After that I posted this question, I have experienced yet. I have manually edited visaconf.ini so that numbers ASRL agreed with Device Manager of / ' Windows port assignment and low and behold, it worked! If this happens on the PC client, installation of MAX would probably be best solultion, however.

  Now I'm wondering if the VISA resource find vi is just read this file? I guess that Yes.

  Thanks again,

  Ed

• MAX does not show my Instrument GPIB

  Hello.

  I have an instrument which I control through GPIB interface.

  The instrument is a model of arbritraty 301 Wavetek function generator.

  I already downloaded and installed the drivers for this mode of the instrument.

  I want to control this instrument through PXI My system having integrated controller NI PXI-8105.

  The controller itself have connector GPIB whereby I connect the instrument Fgen. SO the GPIB address would be 0.

  Today, Max under 'devices and interfaces' it shows GPIB0(PCI-GPIB).:manhappy:

  When I am pressing the button "Scan for instrument" then it shows that the error occurred and no instrument is however I connect the Fgen and provided properly.

  It gives no details about the error.

  Device OR 488.2 driver is also installed in the PXI.

  In the function generator is a logical address of the device selection option. who is correctly set to 2. I tried with change to 0 also, but it did not work.

  Is this really the problem with the Instrument itself?

  Hi, Dennis...

  Not need a photo bleow error message...

  Today I received my GPIB instrument, don't know how.

  Probably as a result may be the reason...

  Yesterday, at the start when the instrument has not been detected, I thought and he got a solution that NEITHER 488. 2 has not been installed on this system. (In referance for this 488.2 NOR being not installed I had posted a message before saying that "could not install NOR 488.2 on PXI '-he was rolling back, I had also placed pictures of this facility.) You can see this Post)

  Then I tried installed NI 488. 2 (yesterday), but failed with the same error. After 2 tries, it was installed successfully, but could not fund the reason for this... (You can help me if you find the reason for this... See the error in installation OR 488.2 PXI system)

  After you install the NI-488. 2, I tried again to find my GPIB instruments. but I got the same error. It should be noted that I had not restarted my computer after installing NI-488. 2.

  I think this must be the reason not to detect the instrument yesterday...

  By the way, thanks for helping me in this and other issues...

  God is with me.

  Thank you again...

• Compatibility of 64-bit of Windows 10 NOR-MAX,

  I plan my (forced) migration to Windows 10 this summer for my PXI chassis and noted that NEITHER-MAX 15.0 is not currently compatible with Windows 10, 64-bit (http://www.ni.com/white-paper/52818/en/) operating system. Has anyone heard any news on when / if will produce a compatible NOR-MAX always remember how much time OR took based on the latest versions of Windows?

  National Instruments for Microsoft Windows 10 product compatibility

  MAX 15.0

  It is compatible with Windows 10 64-bit as long as you are using the 32-bit version of the software.

  Event take a look at National Instruments for Microsoft Windows product compatibility 8

  You will see as very few packets NOR is designed to run natively as a 64-bit software on 64-bit Windows version.

  Read also

  LabVIEW 64-bit vs 32-Bit Applications FAQ

  White paper: the use of products from National Instruments on 32-bit and 64-bit Windows
  White paper: National Instruments for Microsoft Windows Vista product compatibility
  White paper: National Instruments for Microsoft Windows 7 product compatibility

• The analysis of the data of a string of series

  Alert LabVIEW Express 7

  Sorry, all I have to work with and there is no budget at the moment to upgrade.

  Hello, I am in phase 1 (data transfer reliable to labview) 24/7 of my small Miettinen, who is to display and record data environmental Lab 24/7 our Fisher 02-403 digital barometer that has a serial port. In fact, it came with the software, but no one here seems to like use it so I'll try to find something more intuitive. I can't find any info at all about I/O with this device, so I'm reverse engineering. I'm sure that you cannot write anything to this device only read.

  I started with the connection of the device and the interface with NOR measure and automation and received the following string: P,43,1019,44,31,01,0023.0\r\n.

  I tried to use the Labview 7 Express e/s Companion Instrument, selected 1 COMM, changed the timeout to 5000 (trial and error), added a step reading and analysis, ran and received the following string: P, 43,0999, 44,41, 01,0018.0, XX. After well guess, I determined that the values I have in bold change with the environment and the other 3 are always the same idea 9no what they represent). Alphabetical 1 in bold represents the tendency of climate S sunny = P = C sunny cloudy = etc., the value 2 is the atmospheric pressure in hPa, the 3rd is % relative humidity and the last is the temperature in Deg. C.

  At first, I tried to create simply chips for data I want and operation loop the wizard of e/s in awhile, but often error messages obtained suggesting that I need to define all the tokens in the string. I did it and it worked, then I opened the front panel to access the underlying schemas whence I came with the attached VI. I left this race for more than 24 hours, no error, seems good.

  My question on this forum is, can I simplify this VI losing a part of the analysis of the data that I don't need at this point?

  Please let me know if you can not access this VI maybe I can do a screenshot or something.

  Thank you

  Doug

  Yes, it can be simplified to just a bit.

  

  Since you are new to LabVIEW, you can start with the basic tutorial.

• Suggestion regarding mitigation of the probe in the instrument Tektronix 7000 Series Driver

  
  

  Hello Brian,.

  In the Readme of the instrument under problems driver known:

  To report any questions or comments about this instrument driver, please send an email to [email protected].

  As this is a pilot certified NOR supported it but only R & D can change it.

  Kind regards

  Mart G.

• NOR-MAX noncontinuable exception

  Hi all

  See the attached screen shot. When I try to change the NOT-Max camera file, I get this "noncontinuable exception." The file in question worked last week, and in fact NEITHER-MAX won't let me change any camera file that should work with this camera.  The camera is an evaluation from a supplier of the probe card and the file .icd I'm moving them here - it is currently working with my file .icd updated the. For me, it's the strangest part: the equipment works, everything is speaking to each other, I just can't change the camera files.

  I tried to run OR-MAX as administrator, thinking business HE might have eliminated a change of permissions. When I run as administrator and select the new camera file, NOR MAX just goes down, no pop-up window and the file still does not change.

  Windows 7; OR MAX 14.5, LV 2014

  PCIe-1433 framegrabber

  I'll try to save a file in Camera File Generator. I'll post more information, if I learned something.

  Thank you!

  Crazy

  Installation LV2015 has indeed fixed the problem OR MAX. If a part of my previous installation has been corrupted. When I tried to repair the installation earlier today, I had not the installation media going TO practice (or I could have deleted the download like a fool), so I jumped this repair. Now it seems that the problem lies in him GOING somewhere.

  See you soon!

  Crazy

• VI do not transfer data from the instrument.

  Hello to all who are interested.  I'm working on an instrument driver for an Agilent D3000A generator of signal (E4432A) trying to get the generator to sweep the amplitude of - 30dBm to-75dBm and then come back in a loop.  The loop is in a structure of the event and is called by a switch on the front panel.  When the switch is selected event triggers and loop information is passed to the VI.  The problem is the 'Sweeping Steps' VI does not use data from the number of points in the sweep and pause at each time and the tracks of the loop as the amplitude is just switching between the min and Max amplitude levels.  But once I have stop the generator program will continue sweeping (only in a sense) but the correct time and the number of points.  When I use the spy "measurement and Automation Explorer" program AND I do not see that the data are transferred in the instrument.  I don't know if the Subvi the execution order is correct and was amazing if someone could take a look and let me know if I have them in one order incorrectly.  Could not find an example of this type of program examples of the driver so there is little help.  I joined the program and the driver of instruments for your comment, then please take a look and send any information you think will help me to get this working properly.  I have also tried to run the single sweep mode sweep and have just the change of direction for the sweep to the other side of the ramp, but I still get the same results.

  The generator has 15th and ONU3 options.

  I, m using LabVIEW 2010 on a Dell Dimension 2400 running Windows XP and service pack Version 5.1.2600 Service Pack 3 Build 2600.
  Please let me know if you need other information.

  Thank you

  Just for the short term, right click on the structure of the event, select Configure the events managed by this case and uncheck the lock front panel.  Also, I don't know if you caught my edit.  I think your problem is your expectation (or lack of).  At your expectations to be slightly more than the number of steps to multiply by the pause time.  You must leave the instrument perform its scanning after all.

• How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

  How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

  Hung Nguyen

  Hung Nguyen,

  The installation of drivers for all targets in real-time remotely is more or less the same. First install the driver (in your case the NO-Sync) on your PC, then install it on your system remotely through MAX. For step-by-step instructions, see install the software on your NI CompactRIO controller.

  See you soon,.