Not getting no sound on my Vista computer

Similar Questions

• Equium A300D - 13 X can not get any sound using Win7 32 bit

  Hello

  ive installed win 7 home premium 32 bit but can't get any sound.
  I downloaded the drivers available here but still no joy?

  I then started to vista only to find yet, I couldn't get all of her even if the drivers installed etc...
  Also read here that it's realtek hardware so I downloaded drivers off there website but still no joy.

  Any help would be appreiciated

  Thank you

  Hi mate

  You installed a wrong driver sound!
  The laptop supports the audio chip Conexant CX20561! It s NOT Realtek but Conexant!

  You must use the Conexant audio driver

  Please see the page of the European driver Toshiba again! The satellite * A300D box contains the correct Conexant audio driver!

  Welcome them

• Can not get a sound in Windows Media Player

  Original title: How can I see my media files?

  I would like to see some video media files, I have downloaded onto my LG Shine of cel phone and when I go to view them with Windows Media Player there is no sound... these files have an extension of ".3g2"... also named as files BLT or 3GPP2 video/Audio files... How to make some audio?... This has to do with codecs?

  Hello

  Please join Microsoft Community where you can find the necessary information on Microsoft products!

  1 did you do changes on the computer before the show?

  2. do you receive any error messages?

  3 is the issue limited only to Windows Media Player?

  Settings in Windows Media Player, some corrupted codecs are some of the reasons for which you can not get audio in Windows Media Player.

  I suggest you follow the steps mentioned below:

  Method 1: Check the volume settings in Windows Media Player

  See the site:

  Change volume settings in Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows7/change-volume-settings-in-Windows-Media-Player

  Method 2: Run the troubleshooter

  See the site:

  Open the troubleshooting Windows Media Player settings Troubleshooter

  http://Windows.Microsoft.com/en-pH/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Method 3: Install the necessary codecs

  See the site:

  Codecs: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/codecs-frequently-asked-questions

  Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Can not get a sound in computer science

  Original title: Audio driver problem. Help, please.

  I have problems with my driver. Recently, I received this computer from my mother, her husband cleaned files from the computers and I think he deleted a sound driver, because it is not read all speakers.

  Hello

   

  Thanks for posting the question in the Microsoft Community!

   

  You are unable to get sound from the computer.

  1. What is brand and model computer?

  2. which version of the operating system are you using?

  If you are unable to get sound into the computer then it's perhaps because of connection issues or if the drivers are corrupt.

  To check if the problem is with the drivers or the connection, I suggest you follow the steps in the site mentioned:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-7&V1H=win8tab1&V2H=win7tab2&V3H=winvistatab1&v4h=winxptab1

   

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

   

   

   

• video downloaded on my computer from an SD card, can not get the sound of these videos while trying to play

  Original title: uploaded the video on my computer from an SD card

  I've just uploaded 45, very short, videos from SD card to my video library on my laptop.  I'm sure that I've adjusted all the volumes on my laptop, but there is no noise coming from the videos at all.  My laptop I s on the possible sound highes and fact that the buzzing when something is strong. The videos all had sound until I downloaded.  Help, please

  Hello

  1 are. what type of video files?

  2 do you mean you can see the video only and no sound in fate?

  3. you play these files on windows media player?

  4. are you able to play other files stored on the computer?

  Check for file types supported by windows media player 12 using the bottom of the article. If the type of video file that you are trying to read is not supported then you may need to install the codec to play.

  Windows Media Player C00D1199

  http://Windows.Microsoft.com/en-us/Windows7/C00D1199

• Can not get myProfile and administrator on vista

  Hello.. On my laptop with vista, when I start and want to connect to my profile, I get the unrecognized profile, I am also sent to a profile of temp and when asked for permision administerive edit users, it does not recognize the password... ideas please... ? THX

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  See also if this applies to your situation:

  http://support.Microsoft.com/kb/947242

  A temporary profile is loaded after you connect to a Windows Vista-based system

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, read the information here:

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  See you soon.

  Mick Murphy - Microsoft partner

• Do not get the sound after having moved to windows 7 Windows 8

  No sound in Windows 7

  Sound indication bar is moving, but I can't hear anything. I checked the speaker connections and even tried the plug to headphones, but still no sound. Device Manager does not have any problem, and I don't get the error messages.

  Here is my system information:

  Motherboard: HP183F

  HDAUDIO\FUNC_01 & VEN_8086 & DEV_2806 & SUBSYS_80860101 & REV_1000
  HDAUDIO\FUNC_01 & VEN_8086 & DEV_2806 & SUBSYS_80860101
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76D9 & SUBSYS_103C183F & REV_1001
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76D9 & SUBSYS_103C183F

  Hi Isabelle,.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  I also know that the inconvenience that you are experiencing because of his problem. I will definitely help you.

  This problem can occur either because of corrupt audio driver or incorrect audio settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Troubleshooting of audio playback and check.
  Reference:
  Open the troubleshooting of Audio playback
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  It search common problems with your volume settings, your sound card or driver and your speakers or a headset.

  If this does not help, use method 2.

  Method 2:
  Please use the suggestions in this article and check the issue.
  Reference:
  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Could not get a sound device QED uplay.

  Original title: qed uplay

  Hello. I use Windows 7 64-bit. I bought a bluetooth dongle to connect to a device of QED uplay. To listen to the music from your computer on my stereo.

  Drivers for the dongle seems good work, and the computer recognizes the QED uplay as a headphone unit to listen I guess that's the closest it will get - but no sound of music from the stereo. Do I need to install drivers for the QED unit? Although the QED unit is registered in page units and printers, it is not available as a player unit in the sound properties. What should do? -Aimablement

  Hi LasseFurdal,

  This problem can occur if the device of QED uplay is not defined as device by default.

  I suggest you to set the default device as QED uplay device and check if it helps.

  a. go to Start and click on Control Panel.
  b. click on her, then a new window will open.
  (c) in the new window click on the tab 'read' and right click on the window. d. click Show disabled devices.
  e. check if the speaker or headset is listed here.

  f. right - click top and select Activate.
  g. highlight the headset (QED uplay device) and click on "set as default".

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Can not get a sound in the bluetooth speaker

  Original title: speakerphone blue tooth wireless hmdx jam paired but does not work

  I bought a jam hmdx wireless speaker and paired successfully with my pc (dell inspiron E1705 with vista), but it does not communicate with my pc.  How should I proceed?

  See this article:

  The audio output is not automatically routed to a Bluetooth audio device on a Windows Vista-based computer

  http://support.Microsoft.com/kb/933144

• I had to put my laptop to the original on the parameters of the box and now I can not get all updates for windows vista home preimum

  I have reset my Toshiba laptop for the orginial on the parameters of the box using my recovery disk that came with the laptop when I bought it years ago. Now reinstall and update of windows, I can not service pack 1. He said that the system may reboot several times, blah blah blah, it is said installed. I just want this computer up-to-date with all the updates. Its use will be mainly internet, e-mails and word documents. Help, please

  How to reset the Windows Update settings?
  http://support.Microsoft.com/kb/971058

  Diagnose and automatically fix common problems with Windows Update
  http://support.Microsoft.com/mats/windows_update/

  Learn how to install Windows Vista Service Pack 1 (SP1)
  http://windowshelp.Microsoft.com/Windows/en-us/help/133c8953-c9cd-4FA5-8883-03e91bb6f2021033.mspx

  Learn how to install Windows Vista Service Pack 2 (SP2)
  http://windowshelp.Microsoft.com/Windows/en-GB/help/105f7420-6f7f-4FE8-8698-2f40ca5f53711033.mspx

• Could not get Basic Code for Windows Vista Home Edition key to work

  It is on the side of the computer, but my vista on the screen says its invalid... I have the code and it will not be taken, it says I have go to vista set up can't find it and I don't know if the computer is even came with the drive, he bought at Factory Direct...

  You can change the product key on the bottom of the system (Windows key + Pause/Break) properties page.

  Use a strong light and a magnifying glass to read the COA sticker.  It is easy to confuse some characters such as B and 8.

• Headphones - can not get a sound.

  The device has been set as a default, and still there is no sound coming out.  He continues to come through the speakers.

  Hey GRANDMAMOM,

  What is the number and the model of your helmet?

  A few tests mentioned below should help to determine where the problem lies.

  Now given that the sound on the computer works correctly, the problem lies with the plug headphones, misconfiguration or the helmet itself. Please check if the headset runs on another computer. If it works, it means that the problem lies in your computer and not the headphones. Or otherwise, if you have a spare helmet, test it on your computer. If it works, then the headphone jack works correctly. Please post the report back so that we can further consider this issue.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Does she not get the restored properly - Windows Vista Edition family

  I did a backup on 2 of vdv - that, once accomplished was reported as successful. Now, I have restored my laptop to factory settings since she was infected. When I use the Center backup and restore and Advanced Restore option - files from a backup made on a different computer - then the hard drive. He starts the backup asking if some files or all - I choose all files in the backup. It then proceeds...

  I got the c# edition installed with which came the SQl-whiel restore the backup of the ih said there is problem with the authorization of users for SQL 2 related records - I click on go come without affecting the rights of the user. In this case 2 times.

  In the meanwhiel, it shows a lot of files being restored in the progress bar. Then he gives erroe that the label of the disc in the drive is not 1 user-Pc-DateofBackup-disk name where as the disk name is the default name assigned when the backup is performed, which is the name of user-Pc-DateofBackup (may not be the suffix of disc 1).

  Then I choose the option ignore this and drive 2-, it gives the same error...

  When I check - I find a lot of files is restored, but they contain no data/files.

  Help, please.

  Here is an article on the restore procedure: http://www.vista4beginners.com/How-to-restore-files to make sure you do this right.  It's a selective restore of a full or selective backup (not a full restore from a full backup) - but since you did a full backup, it matches your processes more closely than would a full restore (which is not available in Vista Home anyway).

  This is a GREAT article on the backup and restore processes in Vista http://technet.microsoft.com/en-us/magazine/2007.09.backup.aspx , but he won't go into detail about the restoration process - considering almost as easy, of course.  But it teaches you a lot about what is possible and how to do it.

  Here is an article on the advanced use of restoration (during normal restore does not work): http://www.mayankraichura.com/post/2009/08/06/Avdvanced-Restore-via-Windows-Vista-Backup-and-Restore-Center.aspx.

  I also found the following (but don't know if it of true or not):

  1. after the start of "backup and Restore Center."

  2. I chose "Advanced Restore"

  3. I was did not an administrator password... maybe because my account is an administrator account.

  4 choose "files from a backup made on a different computer.

  5. in the dialog box indicating "Select the location of the backup to restore", select "hard drive, CD or DVD...". »

  6. under the drop-down list box, select your drive/partition and continue

  7. If all the backups on your drive, it will show a list of them.

  8. in my case, he showed a backup, but in the backup location, it will show "backup location is not available."

  9. I was frustrated, but then I somehow just select this backup (Yes... even if he said that the backup location is not available " ")

  10. and you press "next".

  11 guess what... no error!

  12. a window appeared asking me if I wanted to do a full restore, or I want to select specific folders or files.

  13. I selected the folders I wanted to restore and bingo... it their restored smoothly.

  14. so that the next time see a mistake, try to continue with him... ;)

  I don't know if this will help, but it does not provide much information about the process (when it works).  I hope you find any error or discrepancy in your procedure and it will clear up and allow you to restore.

  I hope this helps.

  Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Can not get a sound in Windows 8

  My headphone is not plugged but I can't hear any sound. evenwhen all she max sound. Help, please! and I checked there is nothing stuck in the outlet.

  Original title: helmet

  Just a simple reboot of the computer. ._. It's THAT simple. I only

  JST realized what he

• HP G62-b24eo: can not get hdmi sound HP G62-b24eo

  Hello

  I can't sound to work on my laptop to my lg 32 tv(32LC51-ZA). (Video works)

  When I go into audio setting is no hdmi in option. (it is not regonize my tv and I clicked on see the disabled devices)

  but when I connect the laptop to my new sound, the led fujitsu monitor works.

  Device Manager show lg as pnp monitor.

  same raspberry pi did not work until I'm forced to use hdmi. (video worked but no sound)

  is there a way to force sound gap even when it is not regonize my tv hdmi.

  Thank you.

  very strange, but I managed to do that work by changing the port hdmi on my TV and now I can see my TV on playback devices.