Not set SSID and no wireless connection not maintained

Similar Questions

• My photosmart lost SSID and disabled wireless without any known reason.

  My photosmart lost SSID and disabled wireless without any known reason. Diagnotics only clue is that the addresses IP, SSID, etc. are empty. However, it can detect the 802.11 network (ethernet address but no IP address) where it belongs.

  I am advised to do an install "wireless", but no indication where to start? Need my Win7 computer USB connection?

  Thanks - I've finally found the Belkin router WPS button so after activation of wirwlwess with WPS on my printer PS B109n the problem has been resolved automatically.

• WIFI disabled on windows vista and cannot wireless connect to the net

  WIFI disabled on windows vista and cannot wireless connect to the net, but bluetooth wireless Wi - Fi and fine switch is activated. Have a problem with ISATAP #5 who is incapable of solving that can be bound.

  All of a sudden I lost my internet connection wireless and I am unable to return.  May be because recent windows update.  Error messages on the wireless assistant say WLAN offshore or disabled.  I have tried every fix.

  In device Manager (under network adapters) shows also that MS ISATAP disabled with "Windows cannot load driver (Code 31).  When I try to update the driver, "Best driver already installed" appears.

  Is there a way to FIX?

  http://support.Microsoft.com/kb/932520

  Read the above re ignore this error message.

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• On windows xp, wireless network settings icon does not appear and I can't set up my new wireless connection?

  I got a new modem from AT & T because of my Wi - Fi connection failed yesterday. I have new installation internet connection and attempted to establish a wireless connection but the wireless network does not appear. I went under network settings, and there is no icon of wireless network parameters? I don't know what it takes at this point or how can configure my WiFi, that's why I ordered the new modem.

  Hi Cindy20011,

  See the Microsoft article below and try the steps mentioned, check if it helps.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

• How Set up and Adhoc Wireles connection encrypted with C4780?

  Hi, I just bought a new HP Photosmart C4780. I set up ad-hoc wireless C4780 with my laptop, it works perfectly. But C4780 SSID, hpsetup, is not encrypted (protected by password). I don't think that this kind of connection is safe enough, I want to establish a wireless connection between my laptop and my C4780, protected by password. Can all the tutorials I found were on the way to put in place an encrypted connection between a router and C4780 wireless (I don't have a wireless router). In any case, thanks for your help.

  The only encryption available is WEP, which is not safe at all, in any case (freeware from the internet may break in 10 minutes).

  If you really want to fix it, print a network configuration of the front of the printer Page while the ad - hoc is connected.  There, you will find the IP address of the printer.

  Type this IP address in a browser to search the pages of internal settings of the printer.  Go to (left), wireless tab and Advanced tab of networking.

  There, you'll be able set a WEP password (to the bottom of the screen).

• between my computer and router wireless connection (vista, premiem windows 7, 64 bit)

  Hey I recently had problems with my connection Wireless between my computer and the router.
  Normally off during the night is not connected to my router or on the internet the next day.

  I have been in close contact to my isp provider and have received a new router and reset my wireless Internet services provider site but I'm still having problems. I have also updated my drivers for my wireless on my laptop Hp G62 and have found that it will not cut when I do not shut down or sleep during the night.

  When you try to solve the problem, it will come back with "problem with the adapter or wireless access point and then asked to disconnect the power to the router. After doing this it will be fine all day.
  I do also to turn a blackberry 9000 "BOLD" and see first thing in the morning if the wireless is connected or not.

  ask for help, here is my last option I have been through everything and had an expert look at my computer where he found nothing wrong with my computer or wireless set up settings.

  any help or advice would be great

  Hello

  1. do you have problems connecting with Windows 7 or Vista?
  2. you remember of any change to your computer before the problem?

  Make sure that there is no interference between your router and your computer. For example. Mobile phones, like the mobile signals could conflict with your router signals and therefore no connection to your computer.

  You can uninstall and reinstall the Device Manager wireless network card.
   
  To uninstall the wireless device manager,
   
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
   
  Pilots should settle automatically after the computer restarts.

   

  Now you can install the latest wireless drivers and check if this solves the problem.

• 5520 HP usb and a wireless connection at the same time

  I have set up my new 5520 HP with USB connected to my desktop (Vista) for maximum reliability and can print via printer share from my laptop (XP), but I'm obviously missing out on HP web services.  Can I have the USB connection or wireless connection at the same time?

  Hello f1charlie,

  Its new r: YES, because it would be 2 printer icons. One for the USB and the other for the wireless.

  The icon of the printer wireless would be similar to Hp 5520 (network).

  You can set these printer (USB or network) icon to by default.

  But again, every time that you want to print using any application. Click file > print, which will display a dialog box, where, in, you can select the printer icon.

  Kind regards
  Jabzi

  Help the community by marking this post.
  Your question has been answered? Mark it as a accepted Solution!
  See a great post? Give it a Bravo!
  I work for HP

• I have recently reinstalled Windows 7 and now I have no option for wireless connection and wireless adapter is not (wireless connections do not show up when I go to set the new connection)

  I recently installed Windows 7 on my PC, and now when I try to set up a new wireless connection, it's impossible. My plug-and-play wireless adapter is not recognized by the computer (but he did more earlier today before installing Windows 7). NETGEAR has the appeal of Microsoft, Microsoft refused to help me for less than 80 bucks, which I can't afford, after buying their product of GD.

  So I was wondering if someone can help me? On my laptop when I go to the networks and together a new network, there is an option to set up a WIRELESS CONNECTION. Can someone help me please? I can't afford $ 80 to tell what drivers to download.

  Thanks and + karma to one who can help me solve this problem.

  Most often when a device does not work, it's because the driver has been corrupted.

  Try reinstalling your.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• Satellite L50-B-2CP - cannot set the wireless connection

  Hello

  I have an out of the box of Toshiba Satellite L50-B-2CP portable wihtout os because I had a free w7 license and the wireless connection is turned off. I downloaded the broadcom drivers both atheros from the toshiba site, but also the intel wireless lan driver but nothing works when I go into Control Panel, wireless network card is not visible, I don't see Bluetooth.

  Any ideas?

  The Device Manager has no intel listed lan card wi...

  Are you sure?!
  Have you checked it properly?
  LAN and WiFi should appear in the Device Manager in the network adapters box.
  Please check this!

• How to make the computer to look for SBRIO on a LAN connection when wireless connections LAN and are active

  Hello

  I plugged my laptop to a SBRIO using a cable, I also did the same mask subnet the SBRIO and my wireless connection for laptop is also active. I run an application to transfer files from the network to the SBRIO. I was able to download the files from the network using the wireless, but when I try to transfer the files from the laptop to the SBRIO the application attempts to use the wireless instead of the connection to the local network. Is there anyway that I can apply to use the LAN connection instead of wireless?

  Thank you

  Mouda.

  You must manually configure the settings for the SBRIO and map NETWORK cable on the PC. They must be presented on the same subnet. Using the crossover cable, you can configure your PC to use an address like 192.168.0.10 with a subnet mask of 255.255.255.0. Configure the SBRIO to use an address as 192.168.0.11 with a subnet mask of 255.255.255.0. The PC uses the network connection by default for all addresses that do not match the specific subnet on teaching secondary (cable in your case) NIC

• Can wireless and wired network connections to co-exist on the same pc?

  My new desktop pc of Windows 7 has a Wireless N adapter, but given that the router is located next to I prefer to use a wired connection. When I enabled both, I noticed that the pc was connected wireless, so I disabled the wireless card and connected via wired LAN.

  I was wondering if there is any way to keep active both and put in place for the wired connection is a priority, and the wireless connection is used automatically when there is no wired connection?

  When more than one network connection is available, Windows uses the one with the lowest metric value. By default, it automatically assigns a metric value based on the rated speed of the network connection. For more details, please see an explanation of the routes Internet Protocol Automatic Metric feature .

  To force Windows to use a specific network connection, assign a metric value to each of them, giving the lowest value to the desired connection:

  1. Press the Windows key + R , type ncpa.cpl in the box, and then click OK .
  2. Right click on the desired connection.
  3. Click on Properties > Protocol Version 4 (TCP/IPv4) Internet .
  4. Click on Properties > advanced .
  5. Uncheck Automatic metric .
  6. Enter a number between 1 and 9999 for the Interface metric .

  Boulder computer Maven
  Most Microsoft Valuable Professional

• My wireless connection status shows that I am connected but I did "no internet access.

  Original title: internet connected but shows "no internet access" why?

  I have a gateway laptop and everything suddenly I can't access the internet.  My wireless connections shows that I am connected but I did "no internet access?  I tried to disconnect and reconnect, but that has not worked.  I tried troubleshooting and it says there is a problem connecting with my modem, but it is impossible because all other computers cell phones/Ipod work correctly on the same connection.  Can anyone help?

  Renee

  Hello

  You did changes to the computer before the show?

  I suggest you follow these methods and check.

  Method 1: Remove all the wireless networks, listed in the network and sharing Center.

  1. click Start and select Control Panel.

  2. open the network and sharing Center.

  3. click on manage wireless networks.

  4 remove all wireless network listed in this list.

  5 restart the computer.

  Select your wireless network and connect (if course, enter your password). Check if you see exclamation of yellow color on the bar strength wireless connection.

  If the method above does not work, proceed to the next method.

  Method 2: I suggest you try the steps from the following link.

  Wi - Fi and in Windows network connection issues.
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  If the method above does not work, proceed to the next method.

   
  Method 3: Reset the TCP/IP stack.
  
  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself: http://support.microsoft.com/kb/299357 .
  If the same problem still persists, then try the next method.

  Method 4: Perform the steps from the link to set up a new wireless connection.

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  I hope this helps!

• No wireless connection on A100-181

  My A100-181 is a month. I managed to have an ADSL (broadband) internet connection at home with Orange France using their Livebox. The connection worked using a USB and a wireless connection using the built-in Atheros wireless installation. However, for the last week, I was unable to establish the wireless connection! The Livebox is synchronized and my cell phone work the front desk, but are unable to connect to the computer and the Livebox! I spent 3 hours on the phone with Orange technicians who tell me now that my wireless card must be verified by Toshiba, as the Livebox is very well (so they tell me). I need to download the latest drivers for my wireless card? Should I delete and start from scratch by using the restore CD? Wireless card function perfectly and then suddenly stop working? I would be grateful for any advice.

  Hello

  First of all please check if Device Manager wireless network card is correctly recognized.
  If it you will not find any yellow exclamation so I guess that the NIC wireless and other devices are working properly.
  So don't forget to turn on the Wlan switch on the side of the laptop and use the function FN + F8

  You wrote that you use the Atheros WLan utility. In this case the Windows WLan configuration must be disabled because the Atheros controls the WLan configuration.
  I put t know if you encrypted you WLan but I recommend disabling this option to test the connection. You can activate it later.
  Please also check if the MAC addresses of filtering is disabled on the router.

  Well, of course, you can try to update the WLan driver. For this, you can consult the page of the Toshiba driver.

• Windows 98 is able to connect to a wireless connection?

  Wireless router for Windows 98 Machines

  I have an old Windows 98 machine and want to connect to my wireless router Lybnksys with a lan cable to upgrade the computer via the internet/downloads.  How can I communicate with the router for Windows 98?

  Hello JanOtterson,

  Support for Windows 98 ended.

  For reference:
  http://support.Microsoft.com/ph/1139

  For Windows 98 compatibility, you should check the specs on the hardware and the software bundled with it. Windows 98 is not compatible wireless zero configuration, so you will need some type of software installed, in order to implement the wireless adapter.

  Please check the links below for features and the compatibality for Windows 7 because it is the most recent and supports wireless connectivity.
  http://Windows.Microsoft.com/en-us/Windows7/products/features

  For Windows 7 configuration required:
  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  Windows 7 Upgrade Advisor:
  http://www.Microsoft.com/download/en/details.aspx?ID=20

  To buy Windows 7 please click the link below:

  http://www.Microsoft.com/Windows/buy/default.aspx

  Hope the helps of information.

  Kind regards.

• OfficeJet 6000 E609n - Wireless concludes SSID and secure network but will not connect

  I use Mac OS 10.5.8. I installed the printer for USB and went to the next step to configure wireless. My secure network, it obtains the SSID and then asks the WPA personal password for the network. I enter this and click on continue and the message comes back, "the Wi - Fi network selected «...»» ' is not within reach of the unit. ' Button choices are 'Change network' or 'Retry '. Despite attempts unsuccessfully repeated. However, I scanned for other networks and found a secure and connected to this network. Go figure. My router is sitting on my desk next to the printer. The router is a D - Link DIR-655 n I'm on cable for ISP services. When I first bought the printer, we were away on vacation, and I've successfully added to my Mac laptop. I have reset the printer found in the then successful and user guide to establish a connection to the House, with the unsecured network (I don't live in a condo so no idea whence the other network). Thank you.

  You can try to update the firmware on your router.  Some of these models have had problems with HP printers and Netgear was subsequently fixed it with a new version of the firmware.