Notice received from sinning a lot of money

Similar Questions

• I installed the app Channel Four and I was never able to use it.  I tried to remove and re-install, but to no avail.  Any notice received with gratitude.  Thank you!

  I installed the Channel Four app on my iPad and I was never able to use it.  I tried to remove and re-install, but to no avail.  Any notice received with gratitude.  Thank you!

  Have you downloaded the correct version for iPads.

  https://iTunes.Apple.com/GB/app/4oD/id432494037?Mt=8

  Click on view in iTunes and download it from there.

• Error Protocol in the package received from the initiator

  I have a Windows 2008 R2 virtual machine connected to a PS of the Group (6210xs and 6000). I have 4 volumes iscsi LUNS for Windows data, two on the 6210 and two on the 6000. The vm is on the 6210. We have implemented the 6210 back towards the beginning of the year, and all volumes of data have been implemented with MPIO 5 or 6 months ago.

  This morning, one of the 2 data on the 6210 disappeared. Windows Disk Mgmt did not show it online or offline, but the windows iscsi initiator showed as connected LUNs. I disconnected the lun and reconnected and immediately handed volume online and has been fully accessible. The monitor EQ had a message to info about the disconnect with "error Protocol in the package received from the initiator" at the end of the message. 2 seconds later, the logical unit number reconnected.

  It sounds like a problem with the initiator of windows rather than a problem of EQ, but I thought I'd check here in any case. It is interesting that it happened only to 1 volume of 4. This volume has been connected since May with no problems until today, and I do not have no changes to configuration since May. Are both the vNIC multichannel vmxnet3 with all the same settings (jumbo frames enabled, unloading of the disabled, numbers for Rx rings, etc.)

  Any ideas on all the settings should I check or change, especially with the network cards for?  I'll probably post this on technet, too.

  Thank you.

  Tim

  Hello

  The problem with iSCSI optimization is that it keeps track of connections.  However, the table moves periodically as you have noticed, the connections.  The switch fw does not understand that.  With each stroke he follows the new session and retains the old.   The buffer allocated for it is rather low.  According to FW versions on the switches, this could be as little as 256 connections.  Over time, this buffer is overrun.  The older of the switch that made to block any new connection iSCSI on port 3260.   So turn it off is the best option.

  Re: trunk. In general the ISCSI traffic is burst, so when you look at the history of the traffic it appears wrong, because he gets on average over time.  So, I would add at least two additional ports to be sure.

  Kind regards

  Don

• is itunes error message cannot connect to my iphone because of an invalid response was received from the device

  get error message that IOS 10 unable to connect to my iphone iTunes 6 because of an invalid response was received from the device

  Make sure you are using iTunes 12.5.1 or later, as it is required to communicate to iOS 10.

  If iTunes does not recognize your iPhone, iPad or iPod - Apple Support

• IPhone will not connect to iTunes - "invalid response received from the device."

  After years of work very well, I went to put some new music on my phone and all of a sudden got this message "iTunes could not connect to the iPhone 'IPhone of David Platts' because an invalid response was received from the device."?

  I've tried different USB ports, different cables (some Apple official, some after market) and several reboots, but nothing works.

  I'm 10.7.5 OSX and IOS 10 phone you.

  Thanks for the help.

  You have a problem.

  It is good that you have told us you're OS x 10.7.5 (current is MacOS 10.12), because it is your problem.

  iOS 10 requires iTunes 12.5.1 or later to communicate.  iTunes 12.5.1 requres OS X 10.9.5 or later version.

  It's (time to upgrade the operating system of your Mac spent).

  macOS - official Apple Support

• iTunes could not connect to the iPhone "iPhone", because an invalid response was received from the device.

  So I am a new iphone 7. I had a 6 before that. Everything was fine until the day where I got the 7, I decided to try a manual on itunes for my 6 backup so that I could put this on the new phone. I use now icloud backup but before that he always did on my computer. Its itunes version 12.2.2.25 as it is the most recent, that I can run with 10.7.5 which is the newest my mac pro can work without hacking it. Again, never had a problem before it save and use it to transfer music. Anyway, I received the message "iTunes could not connect to the iPhone"iPhone"because an invalid response was received from the device." I tried 3 different usb cords. I tried both ports to the front of the computer and all 3 in the back. Abandoned and did a backup icloud. Installed on the new phone. Everything transferred except my music library which is real download of my CD via itunes. If something was wrong on the iphone 6, surely the new phone that starts with a clean slate will be very well... wrong.  Same message. Leaves through ports, cables, etc. Is it just a simple matter of ios 10 now works with my version of itunes?

  A new phone will be iOS10.  iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. If you can not run a newer system, you will not be able to sync this phone to your current computer. OSX 10.9 and 10.10 are no longer available. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

• iTunes could not connect to the iPhone, because an invalid response was received from the device.

  Just bought an iPhone 7 today and received the error message "iTunes could not connect to the iPhone because an invalid response was received from the device." Don't know what that means, and I have never had this problem with one of my previous iPhones. Thank you.

  You run iTunes 7.5.1? iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. If you can not run a newer system, you will not be able to sync this phone to your current computer. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

  If you have any generation of PPC software which works under OSX 10.6 it is not supported in later versions of the system.

• Invalid response was received from the device

  Now that I've updated my iOS 10 6plus my phone will not connect to my macbook pro. I get an error message stated "iTunes only could not connect to iPhone because an invalid response was received from the device. I removed the password and fingerprints, phone rebooted, macbook restarted and still does not.

  Hi kcampagna8,

  Thank you for using communities Support from Apple. We are sorry you are experiencing this problem with your iPhone. If you get an error with "an invalid response" message when you try to connect to iTunes, you can find the troubleshooting steps in the following article useful:
  
  

  Check your USB connections

  If you see the error 4005, 4013, 4014, learn what to door. If you see one of the errors below, you might have a USB connection problem:

  • 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650
  • 2000, 2001, 2002, 2005, 2006, 2009
  • An error message that includes, "an invalid response.

  Follow these steps to see if the problem is with your USB cable, a USB port or computer. Try again after each step:

  1. Use the USB cable supplied with your device. If you do not, try a different cable USB Apple.
  2. Switch to a different USB port on your computer. Do not connect on your keyboard.
  3. Plug it into another computer.
  4. If you still see the error, you can check for any other problem USB, with the third-party security softwareand the problems with hardware.

  If the problem persists, contact The Apple support.

  Get help with iOS update or restore errors - Apple Support

  Concerning

• -What it means and how to fix it? iTunes could not connect to the iPhone from the iPhone Simon Young, because an invalid response was received from the device.

  iTunes could not connect to the iPhone "IPhone by Simon Young", because an invalid response was received from the device.

  You have upgraded to iTunes 12.5.1? iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

  If you have any generation of PPC software which works under OSX 10.6 it is not supported in later versions of the system.

• How can I change the password without original password? received from a friend's computer and they don't remember password and I can't upgrade adobe, java etc...

  How can I change the administrator password without having the original password? received from a friend's computer and they don't remember the password. Unable to upgrade adobe flash player or anything without password.

  Hello

  If this is not applicable, you must reinstall the operating system.

  This is information from Microsoft for when you forgot your XP password.

  "How to connect to your Windows XP-based computer if you forget your password or if your password expires"

  http://support.Microsoft.com/kb/321305

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  "What to do if you forget your Windows password"

  http://Windows.Microsoft.com/is-is/Windows-Vista/what-to-do-if-you-forget-your-Windows-password

  "If you forget the administrator password, and you do not have a password reset disk or another administrator account, you will not be able to reset the password. If there is no other user account on the computer, you will not be able to log on Windows and you need to reinstall Windows. »

  Microsoft prohibits any help given in these Forums for you help bypass or "crack" passwords lost or forgotten.

  Here's information from Microsoft, explaining that the policy:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/keeping-passwords-secure-Microsoft-policy-on/39f56ef0-5d68-41AD-9daa-6e6019c25d37

  See you soon.

• Session INFO iscsi target - has been closed - sign-out request received from the initatior

  today all of a sudden equallogic Group Manager of its getting flooded

  target iSCSI session - was closed - sign-out request received from the initatior

  target iSCSI session - was closed – iscsi inittator connection fauilure
  no response on the connection for 6 seconds

  been trying to figure out what has changed since yesterday, nothing has changed

  the Member of 4100 not showing this info, all connected to the 6100 Member?

  side esxi 5.5 its projection lost way, restoration of path error messages

  clues

  Hello Dan,.

  This first message is normal, because this is a message of level INFO, not WARN or ERROR.  It only means that a connection has been disconnected so that it can be moved to another port in the group.   I suspect that you run MEM?   Who's going to move, start, stop to need iSCSI sessions to hold the input/output symmetrical on the ports available on the berries.

  ESXi 5.x will always report any kind of connection as an error problem.  Even when he is projected as here.  EQL uses a mandatory iSCSI command under the title "async logout" say disconnect the iSCSI initiator then go to discovery and connect immediately.  However, this time it will be moved to another port on a table.   MEM regularly consults the current connections and may decide to change the layout of the connection.

  The 6100 is probably the head of the group.  So it stores and displays all messages from all members of the group.  Buried in the text it can show you that some are from the 4100.

  The other message on the "6 sec timeout" is different.  This means that, during this period, the table failed this server.  Periodically, initiator and Exchange EQL keep packages of persistent delay.  (KATO for short).   This is so that the two are always answer.  If it fails repeatedly, this message appears and the connection is complete.  Once the initiator (server) is back, he will open a new iSCSI session to replace.   You see this message when you restart a server, or there are problems with the network.

  If you are really interested, you can open a case of pension with Dell.  Please gather the diags table (all members), config switch logs, and supports the VM node ESXi.   They can check this info and verity that the configuration is OK.    They can examine the nodes ESXI to ensure they are in compliance with the best practices with Dell's best practices.   There is a Tech report.   TR1091 that covers this.

  You can find a copy here.

  en.Community.Dell.com/.../Download

  Many problems have been resolved by choosing ESXi for current construction, set up in accordance with this document and Sunrise switches to spec as well.

  Make sure also that the EQL table running 6.0.7 or later.  Running current firmware is much better.  Earlier than 6.0.7 saw potential for corruption VMFS Datastore.  Therefore, it is very important to keep up-to-date.

  Kind regards

  Don

• I'm trying to free up some space on my laptop and I noticed that there are a lot of files of programs uninstalled still on it, I was wondering if there is a good free program to install.

  Hi am trying to free up some space on my laptop and I noticed that there are a lot of files of uninstalled programs still on it, I was wondering if there is a good free program to install to get rid of these files or is there any other easy methods I try I wound appreciate the help thanks

  Where are all these files of uninstalled programs located?

  Usually, when you uninstall a program, all files other than the game save files, customizers, or similar are deleted automatically, and those who are 'left' files are usually readily identified you can manually delete directory.

  You can also see if free Revo Uninstaller will help-->

  http://www.revouninstaller.com/revo_uninstaller_free_download.html

  The same page includes a download button for the free trial of the 'Pro' of Revo Uninstaller version (currently $19,62 if you buy it).  Version Pro is said to "Extended searching for leftovers - more advanced scanning algorithms" compared to the free version.

• No response received from the Symantec Server during activation.

  OT: Network network adapter Ethernet NIC wireless networking device
  I just bought Norton 360 5.0 and I can't activate it by Symantec.  An error saying "No response received from the Symantec Server" I have no internet connection, but do not understand why this happens?  This computer is Windows 7 Home Premium.  It is connected to Linksys wireless - G wireless adapt, but as I said I am able to get on the internet like MSN, Facebook, etc.

  Hi LaraAngold,

  I suggest you try the following steps:
  https://solutions.Symantec.com/sdccommon/ASP/symcu_defcontent_view.asp?ssfromlink=true&sprt_cid=c64ef7a8-111C-47d7-88ef-b8e50c5cbd0f&docid=20071025144354EN

  If the above steps fail, you will need to post your question in the following forums.
  http://community.Norton.com/

• Question ESXi 5.5 with turn a virtual computer: "an error was received from the ESX host turning on VM" '22 (Invalid argument)"'DiskEarly on a power Module failed.'

  Here's what happens when you try to turn it on one of my virtual machines (see also accessories):

  Error stack:

  An error was received from the ESX host turning on VM vzilla-ws2012r2e.

  Unable to start the virtual machine.

  Cannot open disk ' / vmfs/volumes/51286ca4-ef967828-664d-001b2129ad71/vzilla-ws2012r2e/vzilla-ws2012r2e_3.vmdk ' or one of the snapshot disks it depends on.

  22 (invalid argument)

  Power DiskEarly module has failed.

  Cannot open disk ' / vmfs/volumes/51286ca4-ef967828-664d-001b2129ad71/vzilla-ws2012r2e/vzilla-ws2012r2e_4.vmdk ' or one of the snapshot disks it depends on.

  22 (invalid argument)

  This circumstance may be linked to a sata cable issue, with the possibility of temporary loss of connectivity, which could result in data loss/corruption, I realize.  It is a laboratory box.  Especially say that the 2 VMDK he complains (trying to light) is both on the grounds of a single physical disk. Data, read and written to the speaker, since the problem are very good (which indicates the wiring problem was resolved, and the VMFS5 file system seems to be in good health).

  No photos.  No related clones.  Just a 2012 Windows Server based VM, with several drive letters in, with those underlying files VMDK residing on different stores of data VMFS5.  Implemented end (these drives aren't really so huge), but far from running out of physical space for the data either. Everything is working great for months, until today, trying to it turns on again.

  You are looking for:

  "Failure error disk beginning module lit" results in this article:

  error disk on start module failed

  which indicates the .lck files may be present.  It does not exist.

  Then upwards, of a variety of other items:

  Re: Unable to start the virtual machine: invalid argument on *-flat.vmdk

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004232

  https://communities.VMware.com/message/search.jspa?peopleEnabled=true & userid = & ContainerType = & Container = & q = module + DiskEar...

  error disk on start module failed

  but alas, none of them seem to relate directly, or exactly.  My vmware.log file is attached below, as well as some screenshots of to show the structure of the unity of this virtual machine.  Hoping that this post proves fruitful, if anyone has had a similar situation.  The data at stake here are (mostly) redundant, but I would rather understand my way of it, in the case where it happens to me again, or can help others.  Many preferred rather than give up, reformat the VMFS and start again.

  Thank you!

  Good news, the best result I could hope. No data is lost. No corruption of the VMFS or NTFS don't drive in the virtual machine. Nice!  Saved me a few terabytes of data restoration and learned a little more on file system of troubleshooting along the way.

  It took a technician of VMware Service excellent, attentive, methodical remote 2 hours in a WebEx previously to resolve problems with these 2 files vmdk manually, because he found that there is a lock on them. I opened a request of Service (SR) # with VMware by following the instructions here:

  VMware KB: Cannot access certain files on a VMFS datastore

  To resolve this problem, apply for support from VMware Support and note this ID (1012036) Knowledge Base article in the description of the problem. For more information on the filing of a request for support, see How to submit a support request.

  I'll cover this saga and the exact process for collecting and downloading of newspapers, through to my TinkerTry.com, including the ride video.  I even captured much of the technical work that has been done. That said, it is true that little of the magic that was made to resurrect the metadata will remain a mystery, given that this piece is VMware.

  I'm ok with a bit of black box, considering how I'm happy that I got all my data, and time savings that the quick recovery represented.

  By clicking on the button "answer".

• Resettlement CS5 troubleshooting my PC had problems, so I had to upgrade to windows 8.  during installation, I received a response that my serial number was not valid.  It's the same serial number that I received from my initial order.  I disabled before

  Resettlement CS5 troubleshooting my PC had problems, so I had to upgrade to windows 8.  during installation, I received a response that my serial number was not valid.  It's the same serial number that I received from my initial order.  I disabled before the upgrade to windows 8

  Contact by web chat support.

  Mylenium