NSLU2 - cannot connect a network - xp home sp3 drive

Similar Questions

• Equium A200-15I - cannot connect to networks

  I have an Equium A200-15I and unable to connect to wireless networks. I can connect properly to my network wireless at home and in the past have had no problem connecting to networks wireless in other places.

  However, recently I have been unable to connect to random networks, some security enabled (for which I have the password) and one that was not secure, but that I have connected to in the past (to my parents house in the middle of the campaign, so no need to secure). He found fine networks and I can click on connect and put the password and then it flashes just between IP address acquisition and disconnected and not connects. I know that passwords are correct. I tried connected to the network woreless manually, and the same thing happens. It's really frustrating.

  I also have problems in playback of some DVD.

  I would appreciate help with this.

  Thank you

  Hello

  The WLAN driver is perhaps the reason for this and the work of doesn t correctly. You should check the Toshiba for WLAN driver update page:
  http://APS2.toshiba-tro.de/WLAN/

  In addition these WLAN issues may have different reasons. Also, a bad WLAN configuration would be possible. So, you should check the WLAN settings and configuration of the router. Also, an update of the firmware on the router could be useful.

• Cannot connect Cisco Network Assistant to 2911 router

  I'm trying to connect my Cisco 2911 router to my community at the NAC.  I can see the routers in terms of topology, but when I try to add to the community I get an error message indicating that the router is inaccessible (cannot connect).  I can ping client device of soul. I can view the properties of the device to the card (device type: CISCO2911/K9). Telenet attempt connection, but we have only use SSH for connectivity (the same as all my switches that are connected to the community).  2911 is listed as a taken router supported on the Cisco site.

  Any quesses what I am doing wrong?

  Thanks in advance.

  J

  Hello
  You must enable http for can work.

  http://kirkpbm.WordPress.com/2008/07/13/Cisco-network-assistant-enabling...
  Pls link for other instructions above check.

  Rgds/DP
  Sent by Cisco Support technique iPad App

• Satellite A300 - Wi - Fi does not work and cannot connect to networks

  I've had my laptop for 3 months. The wi fi and internet worked but I tried to use the cable home for the internet lan and wifi at the University, but it does not connect.
  I'm sure that I have not dropped the lap top. I took the laptop to check at a friends for wifi and without success.

  It's maybe something broken inside? Because I tried to connect to the network via a cable, but it does not find when it is supposed to.

  Please help :)

  > Wi fi and internet worked but I tried to use the cable home for the internet lan and wifi at the University, but it does not connect.
  > Because I tried to connect to the network via a cable, but it does not find when it is supposed to.
  Stand by. You only have this problem of connectivity with WIFI (wireless) or with LAN (cable) too?

• Spectrum HP notebook: New HP Notebook's spectrum cannot connect to wifi at home

  Just bought new notebook spectrum, tried to connect to the wifi at home, entered security code (that's my 10-digit phone number) and it connects, says: "Unable to connect to this network."

  I'm typing this now on the old computer connected to the network.

  Tried everything suggested, including reinstall them the driver, restart the computer, etc..

  Figured it out: reset my modem wireless by entry into the administration of the modem using my IP, not exactly what I did but it changed the SSID of "Babylon" to "Babylon 2" even if the administration still shows as Babylon

• Smartphones blackBerry 8320 cannot connect to wifi at home

  I recently got a BB8320. All right, I get emails and can send in public hotspots that I am able to connect to Wifi, download EDGE or sometimes UMA. But with my home network wireless, I have a connection problem. Searching for networks brings my router. I select Connect and enter the WPA key but I get an "impossible to associate with the network" error message. This could be to do with my ISP? (Tiscali, in the United Kingdom). Mobile operator is Orange. Any ideas, anyone?

  Got home last night, looked at the phone and guess what? Display of SSID wireless and also UMA! Phone has been turned off at night, so I guess I should have restarted after notice of the folling baseball. Thanks for this and hope it helps others :-)

• Phones AnyConnect VPN cannot connect to network ASA high-speed AT & T uverse

  Phones AnyConnect VPN are configured to connect to the ASA 5510 running 8.4 (4), and it uses the Active Directory credentials to connect. The connection is successful external ISP systems including Comcast and smaller independent service providers. However, when all of us at the AT & T uverse service take this phone 7965 even at home it networks fails to make any connection to the ASA at all. A capture of packets on the ASA shows no activity connection to the IP address of our uverse.

  What's more, is that we can successfully authenticate the VPN of the phone when using the local account credentials (e.g. username admin password * priv 15) that are entered on the SAA. AT & T said that they are not blocking the ports. It is the confusion that this works for users to access local connection, but not with A/D.

  So I guess the question is: what is the first handshake TCP/UDP composed when a Cisco IP phone links AnyConnect SSL to an ASA and negotiates the authentication of the number of A/D? For example, what are the port numbers used in this handshake?  I couldn't find all the diagrams illustrating the HRT and the RFC for DTLS do not seem to have the answer either.

  Thanks in advance.

  -Athonia

  Note: we have a TAC case open currently with subject ASA 5510 VPN Edition w / 250 annyconnect user - SSL VPN for phones. Configuration

  I too ran on this issue and here is a description of what I found.

  If you use automatic network detection first trys phone ping the TFTP server, he has learned from the DHCP server or manually set with the parameter of the alternate TFTP server.  If the TFTP server is accessible the VPN will not connect and will not allow the user to connect manually.

  ATT Uverse use DHCP option 150, the same option as Cisco UC uses to automatically set the TFTP servers, to locate the local home gateway so that the STB can join him.  For this reason, you should notice that when you have a VPN phone on the network and view network settings the IP address of the TFTP server is the IP address of your default gatewat (The ATT router).

  Because of the automatic detection of network works in ping the TFTP server that the phone will always think that it is connected to the local network.  The workaround is to manually set the TFTP server on the phone * to the IP address that the TFTP server would have been if she had leared it from the DHCP server on your corporate network.  The reason you should do this instead of just using a Bogon address, is that once the VPN is connected it tryes to register to the address that you specified.

  Please let me know if this solves your problem as it did in our case.

  * If you do not know how to set the TFTP replacement setting you must first select the "replacement" TFTP protocol and press on * #.  This will allow you to change the default no to Yes.  The below named parameter TFTP Server 1 will then allow you to manually specify the address.

• Pavilion 15z: laptop, cannot connect to networks

  My laptop had the problem of unable to connect to any network. The Internet itself works well because the other devices are connected. The icon that appears is a box with a line with a red 'x' in the bottom corner. After the restart it several times, it will eventually connect and show full bars, but the problem occurred more frequently.

  Hi!, natalie3:

  Welcome to Forum!

  Try, with... http://support.HP.com/us-en/document/c03535285

• HP Envy Tablet - cannot connect when away from home

  With Windows 8.1 now, I had to put my login compressed to use MS my account login & password. Works fine at home with wifi BUT when off site and no wifi, I get the message mentioned by a few others "... not ... ne pas connecte connected to the internet, use the previous password...". "or similar. However, the previous password connect in both. Please can you help me?

  Thank you.

  Hello CoconutNZ,

  When you say you "had to put my login compressed to use my MS account login & password", was it necessary for work or do you only do this because you didn't know how to create a Local (not MS sign-in required) account?

  Would be using an account Local rather adapted to your needs?

  I can only think of a couple of things to try.

  1. change your connect you to use a PIN instead of a password help?

  The user account - create a PIN in Windows 8

  2. If this does not work, switch to a Local account.

  How to move your existing Windows 8.1 log-in to a local account - CNET

  Or you can also create a new Local account and move your files from the old account on. Then delete the old account.

  Create a user account - Windows help

  Does that help? Otherwise, I wouldn't know how to fix the broken MS connection problem.

• BlackBerry Smartphones cannot connect to WiFi at home

  Support for Blackberry,

  My phone:

  Curve 8520

  AT & T

  V5.0.0.1067

  As you requested, I post here my results of diagnostic tool Wi - Fi.

  A WiFi connection
  Current profile:
  SSID:
  AP MAC address:
  Security type: pre-shared Key (PSK
  Association: N /.
  Authentication: N /.
  Local IP address:
  Signal level:
  Data connection speed:
  Status: Not raise networks
  Authentication failure reason:
  Network type: 802. 11B.
  Channel network:
  Encryption in pairs: not
  Group Cipher: No
  Gateway address:
  DHCP: N /.
  Primary DNS:
  Secondary DNS:
  DNS suffix:
  Subnet mask:
  Server's domain suffix:
  Certificate: S not
  Software token: S not
  Code hotspot:
  Hotspot message: S not
  Hotspot status:

  VP
  Current profile:
  Address of the hub:
  Contact: N /.
  Authentication: N /.
  Secure the device IP:
  Status: Error: link down
  Hub address: N /.
  Hub IP:
  Primary DNS:
  Secondary DNS:
  DNS suffix:
  Set the subnet mask:
  Restart:
  The life of the session:
  Re-login to:
  Failed connection attempts:
  Certificate: S not
  Software token:

  BlackBerry infrastructure
  Address: //216.9.242.59:44
  Used intellectual property: 216.9.242.59:443; 6086
  Connection: Erro
  Router authentication: N /.
  Authentication server: N /.
  Last Contact to:

  Do you know how to reboot your router? It's pretty simple... Disconnect the power from the router and the CABLE internet, for about a minute, replace and allow the router to boot.

  Similarly, doing a simple reboot on the BlackBerry this way: with smart BlackBerry poweredphone, remove the battery for a minute and then reinsert the battery to restart. A reboot in this manner is prescribed for most defects and errors of operating system, and you will lose any data on the device doing so.

  Now, try again to establish the connection

• Request remote assistance issues. Cannot connect, check network or group may have cancelled etc.

  I have XP, Vista and 7, customers have.  Remote Assistance allows to work with both.  Now, it will work with either, but it does not work with one of the users with 7.  Help, I tried everything.  A few months ago I could access it, now I can't

  Hello

  1. don't you make changes on the computer before this problem?
  2. What is the accurate and complete error that you receive when trying to use remote assistance?

  In response to the questions above could help us help you better. However, you can have a look at the following article which deals with a similar question.
  Remote assistance may not work if Internet Connection Firewall is enabled
  http://support.Microsoft.com/kb/310608

• Cannot connect to Virgin Media Home Hub with Atheros AR5007EG wireless adapter

  My brothers computer has problems to our Virgin Media Home Hub wireless conecting. I contacted Virgin Media Services customer and they say that the driver is the worng version. The computer has a driver adapter G series and we need a driver to adapter N series. What is the difference between the two, and where I could get the adapter driver series N of for the Atheros AR5007EG Wireless Adapter?

  I hope someone can help

  Hi Williams,

  Thanks for posting to the community by contacting Microsoft.

  The drivers are developed by the hardware manufacturer. I suggest you to contact the manufacturer for more information about the driver and support:

  https://support.Atheros.com/

  Let us know if it helps.

• Cannot connect remotely to an external hard drive on iMac

  I have trouble connecting to remote a Macbook (10.10.5) of an external HARD drive mounted which is connected to an iMac (Mac OS X 10.10.5.) The iMac is connected to the internet via an airport express base station 7.6.4.

  I created an account of sharing only to connect to this drive and I've had no success connecting to it outside the local network of this external hard drive.

  Because the Terminal airport express base station is involved, y at - it sort of port forwarding for connect to this hard drive mounting?

  I've only tried to plug the hard disk via finder > go > connect to server > name.local/locationOfExternalHarddrive of the computer and have had no success so I think the explicit base station is the question?

  Any advice is greatly appreciated!

  I've only tried to plug the hard disk via finder > go > connect to server > computer name.local/locationOfExternalHarddrive

  This is assuming you have CCMM configuration and working properly... without it, Wan, there is no way that the computer can find computername.local

  You need the public IP address of the router... and there may be only a single router. Normally, it is not possible to use IP because it is dynamic, with a home ISP accounts then you must configure the global DNS name or a dynamic DNS account.

  Please read Tesserax doco on remote... the best method is Apple CCMM.

  Airport drive - remote (3 methods)

  A simpler method in my humble OPINION is teamviewer... same as Apple CCMM without as many restrictions.

  Any method of remote access requires a careful configuration of the home network. And the Mac must be able to wake on lan... (apple have their own fancy name for it).

• Cannot connect not phone to computer - no driver

  original title: no driver

  trying to get pictures from my phone to computer it is pluged into usb TI sayes CDMA LG USB MODEM driver is not found how to do this job?    I tried to download pilot programs, don't worry I won't spend more money, unless it works

  trying to get pictures from my phone to computer it is pluged into usb TI sayes CDMA LG USB MODEM driver is not found how to do this job?    I tried to download pilot programs, don't worry I won't spend more money, unless it works

  Hey punkroker

  read this tutorial on your question

  http://www.ehow.com/how_4557519_put-cell-phone-pictures-computer.html

  Walter, the time zone traveller

• How to activate Windows XP after the installation of repair when you cannot connect to Normal startup.

  I got XP Home SP2 OEM installed on an AMD machine and the power supply is dead.
  I have a P4, I prefer to use in any case, I moved the hard drives of the AMD machine to machine P4.  Of course, XP wouldn't boot.
  Without saving anything, I performed a repair installation (under the installer, not Recovery Console).
  Everything seemed ok, but eventually, I restarted XP and a message box informed me that I could not connect until I had activated XP.
  Unfortunately, I can not run the Activation Assistant because I can not connect.

  I found that I could start the computer Safe Mode / command prompt and could then start Windows Explorer from the command line.
  I followed some advice I found online: I extracted wpa.dbl drive OEM installation and copied in the folder Windows\System32 and rebooted.  Nothing apparently changed; "" I still couldn't log mode "normal".
  I restarted mode safe mode / command prompt, began to Windows Explorer and installed XP SP3.

  Now I can connect mode safe mode without network but cannot connect with networking.  Normal mode is not yet available.

  When I try to start 'normally', the saying that I need to activate before I can connect message.  If I say 'Yes' to 'Activate now?', the background of the desktop appears (my own shows JPG) - but that's all.  The mouse cursor is there, but I have found no way to access all the features after it.

  I need suggestions for possible patches that will avoid the need to reinstall completely.

  Here is the response of Fracture, it worked for me:

  http://social.Microsoft.com/forums/en-us/genuinewindowsxp/thread/ece30d55-d72d-4FF9-AFE8-a577f0f4564f