Numbering of the SIP Client IP addresses to public IP addresses
Hello
We are developing a new video network with VCS control and 2 highways of VCS. 1 expressway stressed the public internet address face and 2nd Expressway face partner network.
Requirement: Internal SIP endpoint need dial IP address public (via Highway 1) and the IP address of the partner (via Highway 2). VCS control configured mode "calls to unknown IP address" to "Indirect".
The two highways set up for 'Request to the unknown IP' mode to 'lead '.
There is research on the VCS control rules to find the IP address.
Priority 1 for IP address via 1st Highway
Priority 2 for Ip address of partner via Highway 2.
The two numbering IP addresses work, but component partner / IP address takes about 38 Sec to finish for the configuration of the call.
When I look at the history of calls on the VCS control, I can see even for the search for the IP address of partners, 1 internet search Expressway and could not reach the IP address and then start to search on the highway of VCS partner and find the Ip address, like that it takes more time to complete the call.
Sometimes, it is time and couldn't make a call of IP address to the IP address of the partner.
is he kind, we can minismise the time for setting up call for the IP address of the partner numbering.
Kind regards
Chris
Chris,
try to disable SIP UDP on both motorways as this should reduce the appeal of 30 seconds preparation time.
Hope this helps,
Andreas
Tags: Cisco Support
Similar Questions
-
Get the Thin Client IP address
Hello. I'm trying to find out the IP address of the machine that I use for programming. I want to use my LabVIEW program on a server. However, the string to the property intellectual VI gives the IP address of the network, so in this case the server IP address. It is a problem, as we hope, in the future, run multiple thin on program clients, if we want the program to know what thin client, it works on. However, I don't have access to the command prompt on the thin client due to administrative restrictions. This eliminates the other solution I found, which was to find the Login Windows user name (each light client has its own unique user name) through different screw which involved the command prompt. Any ideas on how to find the IP address of the customer of the Services Terminal Server Session, I believe that my computer called? Thanks for your time.
I called and he was referred to this, which worked. We use Citrix server and the username thing worked, and we are now able to run the program for each thin client using his user name.
-
Cannot ping the Anyconnect client IP address to LAN
Hi guys,.
I have an old ASA5520 running 9.1 (6) 8 where I installed Anyconnect SSL split tunneling access:
See establishing group policy enforcement
attributes of Group Policy DfltGrpPolicy
VPN-tunnel-Protocol ikev1, ikev2 clientless ssllanwan-gp group policy internal
gp-lanwan group policy attributes
WINS server no
DNS server no
VPN - connections 1
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value lanwan-acl
by default no
WebVPN
AnyConnect value lanwan-profile user type profilespermit for line lanwan-acl access-list 1 standard 172.16.0.0 255.254.0.0 (hitcnt = 48) 0xb5bbee32
Now I can ping, RDP, etc. of any VPN host connected to any destination within 172.16.0.0 255.254.0.0 range.
Here is my routing information:
See the road race
Route outside 0.0.0.0 0.0.0.0 69.77.43.1 1
Route inside 172.16.0.0 255.254.0.0 172.25.8.1 1interface GigabitEthernet0/1
nameif inside
security-level 100
IP 172.25.8.4 255.255.254.0But I can't ping any Anyconnect VPN client connected from my LAN.
See the establishment of performance ip local pool
mask IP local pool lanwan-pool 172.25.9.8 - 172.25.9.15 255.255.254.0
Here's the traceroute of LAN:
C:\Users\Florin>tracert d 172.25.9.10
Determination of the route to 172.25.9.10 with a maximum of 30 hops
1 1 ms<1 ms="" 1="" ms="">1>
2<1 ms="" *="">1><1 ms="">1>
3 * the request exceeded.
4 * request timed out.While the ASA routing table has good info:
show route | I have 69.77.43.1
S 172.25.9.10 255.255.255.255 [1/0] via 69.77.43.1, outdoors
Other things to mention:
-There is no other FW between LAN and the ASA
-There is no FW or NAT configured or enabled on this ASA(see her running nat and see the race group-access they return all two virgins).
-FW Windows on the Anyconnect workstation is disabled (the service is running). I also tested and able to ping to my workstation Anyconnect House of another device on the same network.
So, I'm left with two questions:
1. first a I do not understand: after reading some threads here, I added this line standard lanwan-acl access-list allowed 69.77.43.0 255.255.255.0
out of ping and tracert commands remains the same, but now I can RDP to the docking station VPN connected to any workstation LAN;
What happens here?
2. how can I do ICMP work after all? I also tried fixup protocol icmp and icmp Protocol Error Correction, still no luck
Thanks in advance,
Florin.
Hi Florin,
The entire production is clear enough for me
in debugging, you can see that traffic is constituent of the ASA
"Inside ICMP echo request: 172.17.35.71 outside: 172.25.9.9 ID = 22 seq = 14024 len = 32.
the SAA can be transferred on or can be a downfall for some reason unknow
can we have a wireshark capture on the vpn client to see if the icmp request is to reach the customer? I want to just isolate the problem of fw so that we can concentrate on the ASA rather than silly windows ;) fw
made the RDP Protocol for VPN client for you inside the LAN work?
run logging on ASA and ping and then inside to VPN client and the Coachman connects on the firewall, if ASA comes down the pkt it will appear in the log.
loggon en
debug logging in buffered memory#sh logging buffere | in icmp
#Rohan
-
Can built-in DHCP of WLC provide IP addresses for the wired client?
Hello
We have a WLC running on 7.0.98.0. It provides IP addresses for users without comment thread. Now, we would like to put a couple of wired posts for customers who do not bring mobile no. I wonder if I put these workstations on the same vlan without comment thread, they can always get IPs of the WLC. If this isn't the case, I put the static IP on these workstations.
Thanks in advance.
Robert
Rob:
The answer is simply "no". WLC cannot provide clients wired on the same VLAN wireless whose IP address if DHCP is configured on WLC.Fbarboza above metnioned is a 'very' special configuraiton on wireless LANs where the WLC is configured to support some wireline customers and he needs to have two WLCs (the show is called Wired comments). This particular case does not apply to your situation.
With your situation, my answer above apply.
Note
A internal DHCP server pool will only serve the wireless clients of that controller, not clients of other controllers. Also, internal DHCP server can only serve wireless clients and not wired clients.
Reference: http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70wlan.html
HTH
Amjad
-
The ID attribute of the station call needs for Anyconnect VPN client MAC address
Hi all
We test tring Anyconnect VPN users to connect using the certificate. ASA East of validation / authentication user based on cert and approval it requires Radius server (ISE). Currently ASA sends the Ip address of the VPN client in «calling station ID» We want ASA to send the Anyconnect VPN client MAC address to the radius server in RADIUS attribute «calling station ID» Is it possible to do this. Get around them?
Parag salvation,
The calling Station ID always contains the IP if Anyconnect VPN.
L3 is originally unlike wireless which has L2 Assoc.
Currently no work around.
Respect of
Ed
-
IP address connection sets using the VPN Client
Hello world. I'm using a VPN Client when I establish a VPN Tunnel with a 1600 router, and I have a question.
Can I assign a fixed IP address in the client, instead the router send to random addresses from customer?
What I would he do this?
It would be in the configuration of the VPN client, or in the configuration of the router?
If so, I'm doing this?
Do I need another tool, or other software or hardware to do?
any help is hope...
Thank you...
Hello
I don't think that there is a simple way to do this.
However, if you create a different groupname for the user who needs a static IP address, I think you should be good to go
So what you need to do, create a new pool of addresses. Make the start and end ip address be the same (this is the address to which you want to assign to the VPN user)
Configure another ipsec on the router group and bind the new pool to this group
Ask your VPN client to connect to this group
Hope that helps
Jean Marc
-
static ip address to the remote client asa 5500
Hi all
I am trying to configure static ip on the remote client side of the user, I use the following as an example doc, but I don't get the ip address which I am mentiong the user.
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080a7afb2.shtml
my version of the asa is 8.2 (1)
Thank you
Cyril
Great to hear. Pls kindly marks the message as answered while others may learn from your post. Thank you...
-
Dear.
I use ebs 12.1.3 and db 11.2.0.3 OS OUL5x64
in one applTier, I could see the ip address of the clients when they connect to the system in the access_log but
with the average level has 2 servers AP1/AP2 configure with a LoadBalancer in front.
verifying the connection in the Apache log file (access_log.1410393600) we see that the balancer IP address of load.
Please let know us if he died to set up so that I can see in file access_log which client (Ip address) connected to Server (AP1 or AP2)
Thanks in advance.
Concerning
Please see (how to show the Client IP address in The Access Log when using A load balancer (Doc ID 1355549.1)).
Thank you
Hussein
-
I built an application of web service in Jdeveloper 11.1.1.7 to be used by other clients. Just the General steps as follows (Server web service Application is generated--> deployed on the server-> used by clients with the location of the WSDL file).
Now, I met a requirement where I need to get the port number and IP address for the client.
Questions :
How to get the IP address of the calling client to the web service application generated in Jdeveloper?
Commune technologies used to build web service applications is AXIS or CXF. What Jdeveloper technology use to built web service application?
The common technologies used to build web service applications is AXIS or CXF. What Jdeveloper technology allows built web service application?
It depends on the option selected during the creation of web services (if I remember correctly, there are several options, style J2EE 1.4 RPC style JavaEE JAX - WS 1.5,...)
For example, to get the ip address of the compatible with jax - ws web service, you need to inject the context in your service class with:
@Resource WebServiceContext wsContext;
and then inside your method:
MessageContext mc = wsContext.getMessageContext(); HttpServletRequest req = (HttpServletRequest)mc.get(MessageContext.SERVLET_REQUEST); String ip = req.getRemoteAddr();
Dario
-
Find the name of host or IP address of the Workstation client of Virtual Office
Hello
I want to find the name or IP address of the workstation of the user within the virtual desktop OS. Both are Windows XP. The reason is that I want to run a logon script to run an application on the virtual desktop that establishes a network connection on the user's desktop. For example:
(1) user establishes a connection from their local workstation (IP: 10.1.1.25) to a virtual office
(2) the command runs on the virtual desktop that retrieves the name of the host or IP of the virtualdesktop (10.1.1.25)
(3) another command is running on the virtual desktop, which establishes a local network on the virtual desktop to workstation(IP:10.1.1.25) connection of the user
(4) users and I are happy because it's all automatic
Anyone have any ideas?
Thank you!
KO
Hello
There are several ways to do what you want. The easiest way is to use the local environment variable %CLIENTNAME%.
Go in the virtual desktop from the command line, type: echo %CLIENTNAME%
Now you should see the name where the client connects from the client.
What you have to do is to write a script that gets the variable ping, of the environment, the name and read the answer which is the IP address.
You can use the VB script that or a command script.
Thank you
Chris
-
How to change the IP host address list when you connect in the vSphere client?
Is it possible to edit the list of hosts/ip I get when connecting in the vSphere client?
Thank you!
As far as I know it is possible by editing the registry. The key you are looking for is HKEY_CURRENT_USER\Software\VMware\VMware Infrastructure Client\Preferences\RecentConnections
André
-
SPA112 &; SIP122 - bytes of garbage sent using the SIP over TCP
Because the port UDP 5060 is blocked in my case, the SIP over TCP is a good solution for me.
But when I put SPA112 to use SIP over TCP, the server record is still broken.
(I used the version of the firmware is latest: 1.3.3 but older versions has the same behavior.)
After capturing packets, a problem is found:
Each time before SPA112 has sent a message to register, there were 9 frames of data sent before him.
Each frame has 20 bytes, and the content is the same.
The 20 bytes has a motive: the first 4 bytes is always 00 01 00 00.
So come with 4 * 4 bytes, for example, d8 22 6 b 17 d8 d8 d8 22 6 b 17 22 6 b 17 b 22 6, 17
So, in the stream TCP, the register message is like:
....."k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. » k.. » k......"k.." k.. "" k... "k.NOTIFY sip:sip.callwithus.com:5060 SIP/2.0
Via:...
The server responded immediately "SIP/2.0 484 address incomplete."
Then send SPA112 record message again, this time it succeeded and the server response "SIP/2.0 401 Unauthorized '.
Seems good.
Subsequently, SPA112 has sent a new message digest information register but the bytes of garbage appeared again.
Is there any configuration on this bytes of garbage?
It seems that you hit the Nice firmware bug. I can tell you what I see in captured TCP stream.
Your client is connected to the SIP server, but it is not start sending SIP messages - it STUN via the stream instead. You caught "STUN Binding request" nine times before the first SIP package. And an another STUN is tried before the second REGISTER.
This is a bug with doubt - STUN have nothing to do in the stream TCP SIP. As the switch waits for the SIP packets, it is confused by byte STUN causing packets SIP to be misunderstood and rejected.
Unfortunately, I have no idea how to report a bug in firmware to Cisco, unless you are willing to pay for it.
On the other side, it would be that hard to solve the problem. Just disable the STUN.
Thread mark as answered if it solves your problem, it will help others to find solutions.
-
ASA Anyconnect VPN do not work or download the VPN client
I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config
XXXX # sh run
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaaDHCP-client update dns
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endXXXX #.
You do not have this configuration:
object network DMZ nat (dmz,outside) static interface
Try and take (or delete):
object network DMZ nat (dmz,outside) dynamic interface
-
The VPN Clients cannot Ping hosts
I'll include a post my config. I have clients that connect through the VPN tunnel on the 180.0.0.0/24 network, 192.168.1.0/24 is the main network for the office.
I can connect to the VPN, and I received a correct address assignment. I belive tunneling can be configured correctly in the aspect that I can always connect to the internet then on the VPN, but I can't ping all hosts on the 192.168.1.0 network. In the journal of the ASDM debugging, I see pings to the ASA, but no response is received on the client.
6 February 21, 2013 21:54:26 180.0.0.1 53508 192.168.1.1 0 Built of ICMP incoming connections for faddr gaddr laddr 192.168.1.1/0 (christopher) 192.168.1.1/0 180.0.0.1/53508 Any help would be greatly appreciated, I'm currently presuring my CCNP so I would get a deeper understanding of how to resolve these issues.
-Chris
hostname RegencyRE - ASA
domain regencyrealestate.info
activate 2/VA7dRFkv6fjd1X of encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
name 180.0.0.0 Regency
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
link to the description of REGENCYSERVER
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
link to the description of RegencyRE-AP
!
interface Vlan1
nameif inside
security-level 100
192.168.1.120 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP x.x.x.x 255.255.255.248
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 208.67.220.220
name-server 208.67.222.222
domain regencyrealestate.info
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 Regency 255.255.255.224
RegencyRE_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
outside_access_in list extended access permit icmp any one
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask Regency 180.0.0.1 - 180.0.0.20 255.255.255.0 IP local pool
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM 255.255.255.0 inside Regency location
ASDM location 192.168.0.0 255.255.0.0 inside
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 12.186.110.2 1
Route inside 192.0.0.0 255.0.0.0 192.168.1.102 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
LOCAL AAA authentication serial console
http server enable 8443
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
SSH version 2
Console timeout 0
dhcprelay Server 192.168.1.102 inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 69.25.96.13 prefer external source
NTP server 216.171.124.36 prefer external source
WebVPN
internal RegencyRE group strategy
attributes of Group Policy RegencyRE
value of server DNS 208.67.220.220 208.67.222.222
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RegencyRE_splitTunnelAcl
username password encrypted adriana privilege 0
christopher encrypted privilege 15 password username
irene encrypted password privilege 0 username
type tunnel-group RegencyRE remote access
attributes global-tunnel-group RegencyRE
Regency address pool
Group Policy - by default-RegencyRE
IPSec-attributes tunnel-group RegencyRE
pre-shared key R3 & eNcY1.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:35bc3a41701f7f8e9dde5fa35532896d
: end
Hello
-be sure that the destination host 192.168.1.x has a route towards 180.0.0.0 by the ASA gateway.
-Configure the following figure:
capture capin interface inside match icmp 192.168.1.x host 180.0.0.x
capture ASP asp type - drop all
then make a continuous ping and get 'show capin cap' and 'asp cap.
-then check the ping, the 'encrypted' counter is increasing in the VPN client statistics
I would like to know about it, hope this helps
----
Mashal
-
Site to site VPN with the VPN Client for both sites access?
Current situation:
Scenario is remote to the main office. Site IPSEC tunnel site (netscreen) remote in hand (506th pix). Cisco VPN Client of main office of remote access to users.
It's that everything works perfectly.
Problem:
Now we want remote users who connect to the seat to also be able to access resources in the remote offices.
This seems like it would be easy to implement, but I can't understand it.
Thanks in advance.
Rollo
----------
#10.10.10.0 = Network1
#10.10.11.0 = Network2
#172.16.1.0 = vpn pool
6.3 (4) version PIX
access-list 101 permit ip 10.10.10.0 255.255.255.0 172.16.1.0 255.255.255.0
access-list 101 permit ip 10.10.10.0 255.255.255.0 10.10.11.0 255.255.255.0
splitTunnel 10.10.10.0 ip access list allow 255.255.255.0 any
splitTunnel ip 10.10.11.0 access list allow 255.255.255.0 any
access-list 115 permit ip any 172.16.1.0 255.255.255.0
access-list 116 allow ip 10.10.10.0 255.255.255.0 10.10.11.0 255.255.255.0
IP access-list 116 allow all 10.10.11.0 255.255.255.0
access-list 116 allow ip 10.10.11.0 255.255.255.0 10.10.10.0 255.255.255.0
ICMP allow all outside
ICMP allow any inside
Outside 1500 MTU
Within 1500 MTU
IP address outside 209.x.x.x 255.255.255.224
IP address inside 10.10.10.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool 172.16.1.0 vpnpool - 172.16.1.50
Global 1 interface (outside)
Global (outside) 10 209.x.x.x 255.255.255.224
(Inside) NAT 0-list of access 101
NAT (inside) 10 10.10.10.0 255.255.255.0 0 0
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 209.x.x.x 1
Timeout xlate 01:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
crypto dynamic-map Clients_VPN-dynmap 10 transform-set RIGHT
35 Myset1 ipsec-isakmp crypto map
correspondence address 35 Myset1 map cryptographic 116
card crypto Myset1 35 counterpart set x.x.x.x
card crypto Myset1 35 set transform-set Myset1
Myset1 card crypto ipsec 90-isakmp dynamic dynmap Clients_VPN
client configuration address card crypto Myset1 launch
client configuration address card crypto Myset1 answer
interface Myset1 card crypto outside
ISAKMP allows outside
ISAKMP key * address x.x.x.x 255.255.255.255 netmask No.-xauth-no-config-mode
ISAKMP identity address
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 15
ISAKMP policy 15 3des encryption
ISAKMP policy 15 sha hash
15 1 ISAKMP policy group
ISAKMP duration strategy of life 15 28800
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 3600
part of pre authentication ISAKMP policy 25
encryption of ISAKMP policy 25
ISAKMP policy 25 md5 hash
25 2 ISAKMP policy group
ISAKMP living 25 3600 duration strategy
part of pre authentication ISAKMP policy 30
ISAKMP policy 30 aes-256 encryption
ISAKMP policy 30 sha hash
30 2 ISAKMP policy group
ISAKMP duration strategy of life 30 86400
vpngroup address vpnpool pool mygroup
vpngroup dns-server dns1 dns2 mygroup
vpngroup mygroup wins1 wins2 wins server
vpngroup mygroup by default-domain mydomain
vpngroup split splitTunnel tunnel mygroup
vpngroup idle time 64000 mygroup
mygroup vpngroup password *.
Telnet timeout 5
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Hi Rollo,
You can not be implemented for a simple reason, it is not supported on the version 6.x PIX. It relies on the PIX 7.x worm but 7.x is not supported on PIX 506. Thus, in a Word, it can be reached on a PIX 506. If you have an ASA, a PIX 515 running 7.x, a router or a hub as well, it can be reached.
HTH,
Please rate if this helps,
Kind regards
Kamal
Maybe you are looking for
-
Wireless card is not on the Satellite C650-15U
HelloI have a Toshiba Satellite C650-15U, this morning I tried to connect to the Net via wifi, but I saw that there is no connection. In Control Panel, there is no WiFi card, it seems to me that I have no card wireless at all! When I tried to reinsta
-
Photosmart HP 7510 - cannot ping printer; Is on the network
I'm unable to print and scan to my printer. I can't ping my printer but when I look at the wireless settings it has an IP address. I got tired of rattling of the printer from two different computers, a PC connected to the router via ethernet and the
-
ISE of Cisco protocols for ldap and Windows wireless client
Only protocols below are supported by ise in combination with ldap identity sources. EAP - GTC, PAP, EAP - TLS, PEAP-TLS. Peripheral Mac OS appear to be able to use these, but Windows users seem to have problems. How windows users must connect with i
-
Failed to retrieve Windows Photo upward
I backed up my HDD to an external hard drive Western Digital when my computer informed me that my hard drive was about to fail. Then I restored my files to the new HD. The problem is that my pictures have not been restored - the files are there, b
-
HEALING TOOL DOES NOT WORK USING THE FILES DNG OR ANY OTHER TYPE
I tried to correct this eternity, or since I signed. I'm up-to-date on versions and use late model Mac. I have also read the forums and followed all the advice, but he does not want to heal. Any other suggestions?