Officejet 4315 slow printing problems after replacing the print cartridge

my printer was working fine until I replaced my print cartridges. I replaced the black with color with 22 and 21.

my test page prints fine and sometimes my impression is very good. but often, my impression is extremely slow. can't understand why it is slow sometimes and other times it is nice. do not have this problem until I replaced my print cartridges.

I found a post on slow printing and I tried the different steps. don't know what the issue is. Thank you

Real new ink installed HP?

You could remove the cartridges, reset the printer and turn on without the cartridges, and then reinstall the cartridges. Eliminate any power surge strips or extensions, plug the unit directly into a wall outlet.

When you mention slow, how to slow down? How long to print from the computer exactly? How long for a print job initiated from the printer exactly?

Tags: HP Printers

Similar Questions

  • Problems after replacing the cartridge

    Hello

    I have a problem with my all-in-one HP Photosmart C3180. Recently, I replaced the black cartridge with a new one and now I can't print or copy more because it shows a problem with the cartridge three colors (it has not been replaced).

    What happens is that the red error led and the led (the one near the color copy button) color cartridge still flashing. It does not accept any input print and everytime I turn on the printer it will begin what is called "align cartridge" (printing paper with a few lines on this subject).

    Is that what I can do in addition to the replacement of the two cartridges at the same time? I never had this problem before.

    Thank you for your time,

    Alin.

    Hello, AXN

    Unfortunately, you must have the color cartridge to print. I noticed that some printers can still use the scanner if you also need that. You can always try, but it might give an error when you try to print.

    Let me know if the replacement cartridge solves your problem.

  • all the pages of bad qualities with the toner after replacing the toner cartridge

    I just replaced the old cartridge with a new one, but now the pages come out covered in black toner to make the text unreadable. I tried to turn the drum several times following the directions to distribute the toner evenly, but the problem remains. Please advise?

    Hi, Happytohelp01.

    Thanks for your kind response,

    I use a black and white HP Laserjet 1010.

    I am trying to print a text, the printer does not have a digitization Center.

    Yes, this is the first time that I had no problem with this printer.

    The toner is melted and begins to run out, so I replaced it with a new replacement cartridge I bought the printer about three years ago. Later, I shook and reinstalled the old cartridge, which seems to work very well with no black spots. The new toner would be obsolete?

  • Printing printer Lexmark 2600 problems - it prints half a line after replacing the color cartridge

    It prints half a line, if the top or the bottom of it and the cutting of the other party.  This happens on every third line.

    This started happening when I replaced a color cartridge and ran the alignment page.  Before replacing the cartridge, it prints very well (except that the color cartridge started missing).   When I noticed what was going on, I took both cartridges on and then put them back in and had to print the alignment again page.  Yet the problem persists.
    I checked the Device Manager, and my drivers are up to date.  I also checked all connections.
    Any suggestions are welcome.

    Oh boy.  I don't know what I thought.  It just had to unplugging everything & then reconnect them, turn off & on.  This took care of it - seems so simple now.

    I guess it was my new laptop which has the printer all confused.  Win7, my find of CL.

    Insofar as the Lexmark support, I have not yet that day.  In any case, it comes to X 2690 model I had for centuries, so I guess that support would be of any help.  I mean, the guarantee missed a long time ago.
    Thank you for taking the time to answer.
  • The documents don't print well after replacing the ink cartridge

    Original title: HP 6980 printer

    I just replaced the ink in my HP 6980 printer; now all my documents are dirty printing

    Hi, Annette.

    Manually clean the cartridges

    Scroll down to "remove the duplexer.  Clean the rollers alike.

    5 easy steps to clean inkjet printer

    Print quality problems

  • Pavilion dv6 2170 clock problem after replacing the CMOS battery

    Hello world. Sorry for my bad likely English

    OK, so the problem started since I changed my laptop CMOS battery. and to be honest it wasn't whit any problem the clock when I replaced it but I if this may be the cause of another problem that later I figuered what the problem was because of the RAM.

    in any case, I changed the Rams and this problem has been resolved. I just set the clock of the BIOS and rebooted the system. After awhile I figuered that windows clock is not fair. I restarted again and saw the BIOS clock. It has been reset for 2009! even when the laptop battery and power supply are attached the BIOS and windows continues to change clock! I even changed my windows and I replaced the CMOS battery with the former, but nothing helped. It seems really strange, but I don't think it's maybe a hardware problem there a driver or something for the CMOS battery... need your help! Thank you!

    You mentioned that the BIOS has been reset for 2009? This means that there is a problem with the current or any leak and the BIOS has been "reset" back at the root of the plant. I'm afraid you have shorted something when you changed the battery not be grounded.

    Worst case is that there is physical damage to your motherboard and there is nothing you can do about it, probably broken a capacitor - who cannot hold a charge to prevent the reset of the BIOS clock.

    However, you can try this.

    Completely, unplug your computer, remove the laptop battery, etc... Then browse 'Guide' your computer for the "hard physical reset" for your CMOS. I don't know what it's like on a laptop, I only did it on desktop with riders. Be sure to follow the directions precisely.

    -Make sure you are properly grounded. touch the metal parts that is grouned before touching anything on your computer.
    -the hard reset should be done for at least 30 seconds, this ensures that the power is completely served the system. Then you can set this back.

    Try this a couple of times, first without removing the CMOS battery and 2nd time after remove CMOS battery and placing it in.

    Good luck.

    BTW, you can also try running without your new memories (if there is more than 1 stick, try them separately). In fact, I would probably try first before doing a hard reset CMOS. The reason why I didn't say earlier, it's because I have assumed that you already tried this.

  • Satellite L50D - Boot problems after replacing the hard drive

    I just upgraded my hard drive of the pathetic crod 5400 they provide to a SSHD@7200rpm, but now have a major issue.

    I initially image the operating system from the old hard drive to the new drive and have had chronic start-up problems (1-3-4 attempts to start to succeed if it fails at any time (often to the Toshiba start screen)).

    I reinstalled from a drive under Win 8.1 plain own ENT (trying to avoid the bloatware) and it is exactly the same number and is what I used to format the laptop very well with previously and had previously worked.

    I tried reformatting and reinstalling (by removing all partitions on each attempt) to the CSM, unsafe UEFI and UEFI secure. MCS is a straight line never works not proceed and both UEFI methods have the same exact result.

    I tried with original restore disks and it seems to work (not had time to fully test) but I don't want the bloatware and it shouldn't be serious since, if I were a customer who forgot to make restore disks (too often) and just have to have a failed hard drive or replaced sacrificed the laptop would be now a door stop.

    This seems as bad as Apple to lock people in.

    So I would appreciate ideas of people to please, I don't know if there is a program that is supposed to take place on a new drive as PS3 etc (I doubt it), but that leads me into the wall, and will be the last time that I consider Toshiba as anything other than a joke, if there is no solution.

    I had to replace the hard disks many times in my previous Toshiba laptops and were devoid of this crod, it has something to do with UEFI which seems more a nuisance than a help right now.

    TIA.

    Hello

    In my opinion, you should first check if the startup problem is related to the new installed HARD drive or new installed system.
    You said that the laptop fails to start up often to the Toshiba start screen.

    The splash screen appears during the POST (power on self-test) procedure. During this test, the material will be checked.
    I m wondering if the hybrid SSD/HDD isn't recognised by the BIOS during this particular step.

    From my point of few, this could be the reason why the system cannot be started.

    Another important note:
    The 8.1 win requires enable start secure as well as the UEFI boot mode.
    Therefore, you must enable both options in the BIOS.

    Last but not least check if you are using the latest BIOS version as latest firmware for the hybrid SSD/HDD

  • Problems after replacing the motherboard

    I had my motherborad replace and drive hard and now still wmi repeated problems startup problems and disk problems
    now computer freezes up on me I think I will close it
     
    Please you delte this message because you seem to move my posts elsewhere anyway, and have not responded to me
     
    Pleae respond as soon as possible I think THAT MY COMPUTER IS GOING to BLOW UP
    ERROR 8004005 0XC00000D 0X000000 0 X 79
    REPEATED WMI ERRORS AND OTHER MISTAKES TO THE COUNTY PLEASE WRITE ME AS SOON AS POSSIBLE
     
    I could not download the file, I hit copy and got many files, but it wouldn't let me download the file do - what I do?
    now, o took two blue screens and several error what should I do. error fatal 0xfffbf8 error ox0000020 essent and 24 and error 0 x 79
    I had shut downs and crashing and placing of time then going on.?

    Hello

    "I had my motherborad replace and drive hard and now still wmi repeated problems startup problems, and disc problems.

     

    You don't say who 'fixed' to your computer.

    If it was Dell, which is in contact with you soon, get them to repair it properly, or if it was someone else that Dell, take it back to the person who has replaced the motherboard and hard drive and get them to repair it properly.,.

    See you soon.

  • OfficeJet 6600: Error general printer after replacing the ink cartridges

    Since the departure of cargtrides of ink is "Printer failure" and "there is a problem with the printer or ink system" and after pressing on "?" shows only "printer General error" without error code.

    I did all the steps he says I (reset the power) but the problem persists. Ink cartridges are new and HP.

    What could be the problem?

    Hi Chris2612,

    Thank you for your answer!

    I would definitely say to change the cartridges, if that does not solve your problem, then please call our hotline to the 800-474-6836 to get help. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Language-country selector.

    Good luck!

  • Satellite P200-1EE: charger problem after replacing the AC adapter / CC

    After changing my AC power (the old one didn't work anymore) I have problems with the battery charging circuit.
    When the adapter is plugged in and the laptop is turned off, it charges the battery OK.

    If I turn it on it will charge the battery until it is fully charged, the light will be then turns blue for a few seconds and then turns off.
    The battery will then race down until it is completely empty, even if the power adapter is showing as connected.
    Once the battery is fully discharged cell breaks down. Once off, it will start to load again.

    Someone at - it ideas to help me please.

    Hello!

    A friend of mine had a similar problem with its Satellite laptop. He bought a not Toshiba AC adapter and the battery could not be loaded.
    After that, he bought an adapter AC from Toshiba and everything works now.

    On the Toshiba site, you can search for compatible adapters:
    http://EU.computers.Toshiba-Europe.com-online services & -online Options of PC Accessories devices & -Online Homepage Options & accessories PC

    Good bye

  • DV8T 1100 CTO graphic problems after replacing the motherboard

    Windows 7 Pro. Built 3 years ago this month. Motherboard is dead because of damage of water, but not before I could test the CPU and RAM, which has survived intact. Bought a NEW replacement MB of HP parts store. Put it in. It was obvious that the machine was to start the system, but no video. I put on an external monitor. Video about it. Looked at this forum and based on suggestions from the experts on what causes black LCD screens, has decided to buy a strainer as it could have been a cable on the whole of the sieve or video converter problem continuous alternative back light works fine, but I wanted the fixed machine and doing the problems of individual components on the screen. Assembly of the new screen does not work. Windows found the webcam and audio on the new screen (already present with the old screen), but all to change the resolution and rotation is grayed out with a screen.

    No light flashes at startup. The new motherboard BIOS is updated. I did not burn in tests.

    I do not have a second MB work through the ordeal, so I guess that's the new motherboard, as the cover of the keyboard does not work (not that it worked very well before - another thread). Can I have another motherboard spent the night, or return everything and just buy a new laptop, which would probably not be almost as beautiful as the one I have (230 GB SSD, second disk, screen 18.4 "HD) any thoughts? I had to walk away for a day because of the frustration. It is not like putting a motherboard in a desktop computer - even though I'm about half an hour to go back.

    I got a new MB by FedEx, installed today and fortunately use my laptop.

  • Installation problem after replacing the motherboard

    Hi all

    After downloading and installing PremierePro through the creative cloud using ADM, I had to change the motherboard of the computer.

    At it again - Photoshop and illustrator are working well but PremierePro is nowhere to be seen.

    ADM, said the program is installed and so allow me not to repair or re - download.

    I found AdobePremierePro.exe, which I assume to be the launch of application program but when run I get system error - the program cannot start because exrces - c_3.0.dll is missing on your computer.

    Any ideas on how should I proceed?

    Thank you

    Mike

    See if the following can help:

    http://pcsupport.about.com/od/findbyerrormessage/a/libgdk-Win32-20-0-DLL-not-found-missing - error.htm

    If this is not the case, try Google search using terms that you identified ("lack of exrces - c_3.0.dll") and see what remains is available about this error.

  • My printer HP LaserJet 1536dnf printer prints black pages after replacing the toner with a new one!

    I changed the toner cartridge for my printer HP LaserJet 1536dnf with a genuine HP toner cartridge and now it's printing the pages in black.  Any suggestions on how to fix this?

    Thank you!

    Hi @Beaglemom49779,.

    I see by your post that you have replaced the toner and now get all black pages. I can help you with this.

    Have you had the same problem with the printer before replacing the toner?

    It could be a hardware or with the printer fuser problem.

    If the problem started just after replacing the toner then most likely, the toner.

    Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector)

    Number one cause of problems with toner.

    Check if the drum unit for damage:

    1. remove the cartridge of toner product and check that the tape has been removed.
    2. check the memory chip for damage.
    3 examine the surface of the imaging drum on the bottom of the toner cartridge.
    CAUTION: Do not touch the roller (Imaging drum) on the bottom of the cartridge.

    His fingerprints on the imaging drum can cause print quality problems.
    4. If you see the scratches, fingerprints, black on the drum, or any other damage on the imaging drum, replace toner.
    5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem is resolved.

    Please call our technical support if the there is a problem with the toner and you learn about a replacement, to the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Contact HP.

    Good day!
    Thank you.

  • Will not print black after replacing the black ink tank

    After replacing the black ink tank, the printer does not print black data (text or graphic).  I ran printing HP and scan doctor utility and printed assessment page.  The text is printed in a pale blue color. Gray scale apperas block (far right) to have no black content and has a hint of cyan.

    Printer:

    HP Officejet 6000 E609n

    Thanks in advance for any help

    OK because that is a thing of warranty which may be worth dip the printhead as described below...

    (1) get a pan and put 1/2 "of very hot (not boiling) water in the bottom.
    (2) remove all ink cartridges, then remove the print head Assembly.
    (3) gently put the printhead nozzles down in water and soak for 5 minutes.
    (4) remove the print head and gently dry the electrical contacts.
    (5) replace the print head in the printer and then reinstall the ink cartridges.

    http://h30434.www3.HP.com/T5/Ink-toner-cartridge-printhead-issues/HP-6500-Office-Jet-E709a-black-printer-cartridge-HP-920-not/m-p/447545#M36315

  • Remove the error and check the time cartridge after replacing my black cartridge in my HP 7200 printer.

    After replacing my black cartridge in my HP 7200 printer, it says remove and check right cartridge. It also says this if I put the old cartridge in. Worked well before ink has low cartridge-more

    Cartridge OT:Ink

    Hi Jim,.

    I understand how it could be frustrating when things do not work as expected. Please, I beg you, don't worry I'll try my best to resolve the issue.

    What operating system is installed on the computer?

    I suggest you try the steps from the following link:

    Error message: remove and check ink cartridges
    http://h10010.www1.HP.com/ewfrf/wc/document?cc=us&DLC=en&docName=c00054462&LC=en&product=391151

    Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

Maybe you are looking for

  • First HP: first hp

    Problem writing expression...

  • connection failed

    Hi I am facing a problem in the connection failed on the confrontation of the clan. I am using two game Center account, sometimes I spend it if I need to play my other account. but since now I have a problem that I can not open and show in my screen

  • stuck on configuring updates, help

    I upgraded my pc, it is stuck on configuring updates 1 of 3, 0%, which can do to restore it, I have no cd boot and you cannot get into safe mode, I am running vista, please help

  • Move my Adobe CS 5 to a new computer

    I have Adobe CS5 on a computer I use is no longer. I want to download on my new MacBook. I have the serial number, but cannot find the disc. No reviews phone or chat rooms are available to help.

  • Star tool form something different. How I do?

    I did a form I've ever seen elsewhere. I made a star with the path to the intersection.It is made by the star tool, but I don't know how I did it. I just clicked and dragged. I guess I did it with another key (s).I would like to know how to do.Thank