OfficeJet 4620 stops mid pinting-employment

Similar Questions

• HP Officejet 4620 e-all-in-one stop wireless print whenever it is turned off

  My HP 4620 stop wireless print whenever it is turned off, although it is connected to the network (by the results of the test network wireless, pass & the quality of the signal is excellent).  No troubleshooting - HP Print & Scan Doctor work there is no help, I have to uninstall & reinstall the printer each time to be able to print wireless again.

  I use it on/on button to turn the printer off, don't disconnect not.

  Please help, or I need to return to the store, this is the third time!

  I also had the same issue and after a few game it seemed to have fixed so here's what I did... Hope this helps someone else.

  -My printer is connected to my wireless network.

  -On my computer that I'm connected to the printer through the IP address 192.168.1.153... (Yours may vary) in a browser

  * You can find the ip address printers on the control panel of the printers by pushing the wireless button and pushing the ok option 1, it should appear with the intensity of the signal and the ip address is at the bottom.

  -Once I was on the Printers page in my browser, I went to the tab network at the top.

  -Then to Internet Printing Protocol section (on the left in the advanced settings)

  -On my own PPI was already on, but the location was empty I put a '1' in the location box and then applied settings.

  -C' is the only thing that I changed and now my printer is asleep as always, but when I print something from my iphone, mac or pc it wakes up and prints as it is supposed to!

  BTW before I went to the printer via the browser. I changed layout sleep in 15 minutes via the Control Panel on the printer itself, don't know if it helped the issue or not because I still had the problem of sleep after I set the timer to 15 minutes instead of 5 min. But I solved my problem after performing the steps above!

  Also note that on the one hand some ppl on here say it's a network problem or a router! This is NOT the case I never even tried these roads and I solved my problem only by changing the setting of the printer! I have not set a static ip address or something like that!  The above steps is things ONLY I touched and my problem is SOLVED!

  Router: NETGEAR AT & T 7550 wireless router/dsl Modem

  -Security: WPA2-PSK (AES)

  -Printer connected to the router via WPS (push button configuration)

  Printer: HP Officejet 4620e all-in-one

  Computer: Apple iMac OS X Version (connected to the network via wifi) 10.7.5

  Dell running Windows 7 server (connected to the network via wifi)

  Apple iPhone 4S (connected to the network via wifi)

• OfficeJet 4620: Hangs of HP Officejet 4620 e - all - in - one

  Recently, the printer showed a message on the screen saying "use switch to turn the printer off. The printer does not have a press button. I can unplug the unit and it seems to do normal start when I plug it in but returns the message and it crashes. It will stay like this for hours or days until I unplug the unit. After that I had plugged in I was able to hold the power button and get it into the stop. After being off, I press the power button and it came back but once more posted this message and hung.

  It does not what whether the computer when it is connected via a USB cable. It seems that I can press the power button and it will fit as long I have before tap the blue wireless starts to Flash. After that it will not respond to any key.

  Please notify.

  Hey @clevbucki,

  I see that you have some problems with an error message on your Officejet 4620 e-all-in-one printer you can not delete. If the message is related to a bad power off of the it sounds more like you have a problem with the buttons on the printer. The only thing that could be done would be to replace the printer. You can contact HP support by clicking here and filling out the form below.

  I hope that you are able to get this resolved so that you are able to resume printing.

• How can I turn off ringer on Officejet 4620

  I have an officejet 4620 connected to my incoming phone line. When I'm with a client I want him to not ring. I have a machine ansering in the system and taking calls. How can I disable the ring or make her volume 0

  Also is there a way to stop the light for the wireless network to go or not blink constantly.

  Hi JClaiborn,

  The volume of Fax:

  1. press on the installation icon (key)

  2. highlight and press the setup of the fax machine (2)

  3. highlight and press the basic menu (3)

  4. highlight and press (5) Volume sound Fax

  • Off
  • Soft
  • Loud

  Adjust the Volume:

  1. press the Setup (key) icon

  2. go to preferences

  3. go to Volume

  4. choose the desired option

  • Off
  • Soft
  • Loud

  Turn off wireless light:

  1. press the Setup (key) icon

  2. navigate to the network

  3. turn off the wireless radio

• HP Officejet 4620 is disconnected from the network, how to re - connect?

  I went through all the troubleshooting steps, I turned it switch on the computer power. All my other devices are connected to the network very well except for this printer. It is less than 2 months old and has worked fine since I got it and I not made any changes to anything.  He only stopped to be connected.

  I'm so frustrated... Please help?

  In order to re - connect the printer to the network, you will need to plug in your USB cable.

  1. click on Start Menu

  2. Select all PROGRAMS

  3. choose the HP folder

  4. go to Officejet 4620

  5. add printer or software product Setup &, it should give you option (convert USB wireless).

  With this printer, you need to install the USB printer first, and then convert it to wireless.

  Let me know if this can help, thank you.

• HP Officejet 4620: Installation HP 4620 printer on Mac OS 10.10

  Hello!   I have a HP Officejet 4620.  My printer is fine, but my computer has stopped recognizing my printer suddenly about 6 months ago.  I thought it was the USB connection, so I bought a new power cord USB printer-computer, but it does not solve the problem.  I tried to install the software on my computer to see if I could get a recognition without wire between my printer and the computer.  When I installed it, I got a warning window saying that the officejet does that by 'Mac OS 10.5 - 10, 7'.  I noticed that my computer is Mac OS 10.10 Yosemite.  Is this the reason that my computer is not recognizing my printer?

  Thank you for helping me to recover my printer!

  @charisbrooke

  It's the driver for OS X 10.9 and 10.10

  http://FTP.HP.com/pub/softlib/software12/COL52003/MP-125737-3/HP-inkjet-SW-OSX-Mavericks_v12.34.40.dmg

  REO

• OfficeJet 4620: No black ink

  I have a HP Officejet 4620 ink empty simply stop working. I went through all the downloads, troubleshooting and called customer service. Told me the reason why my black ink wouldn't print was because I haven't used my printer enough, even if the day before it stop working, it works great. I was told that I have would switch to a new printer for the low price of $140 with a 3 year warranty. I've had my printer for 2 years and spent more than $120 for it. I think that spending that much on a printer, it would last 2 years? Maybe it's the lifecycle of HP printers? Im very disappointed with HP on this issue. I was told someone else contacted me and have not heard of anyone yet.

  I just got a phone call from HP and they told me they would me shipping a printer reconditioned to replace mine. I hope it works, thanks for the help

• My Officejet 4620 do not print black ink

  I replaced the black cartridge on my Officejet 4620 with a new high-capacity HP cartridge and it won't print black ink on the test page, any application or function of Copier.  I have reset the printer nothing helps.  The ink level indicates that it recognizes the new cartridge and says it's full.  Black ink out of the cartridge when I put my finger against the exit hole.  I cleaned and aligned the print heads, but still no go.

  just in case someone else has this problem, heres whats really past and heres how to fix this annoying problem. its relatively easy to do and more efficient than wasting money on a new printer or have that he repaired as most people eventually do.

  going on what? the ink has clogged print heads and solidifies closed. the function of "clean print heads" the printer comes with doesn't have the ability to solve this problem. This feature is to clean the heads Sales, not clogged heads. Why hp decided to make this model without a simple to remove the cradle is beyond me, but fortunately the cradle out and can be cleaned with hot water.

  theres a few items, you will need to get there easily, or you could just burst the branch loppers, like I did and vent your frustrations.

  you will need: a pair of slender beak pliers, a screwdriver torx T9 (selling auto parts stores them for a few dollars), paper towels and a space for work (its easier to do this in a corner of a room, on a small table or floor).  Keep in mind that you are dealing with ink, then change your clothes right just in case and also catch a paper plate or a few sheets of paper to print to set ink cartridges while you work.

  (1) ok. lets start. !!! FIRST UNPLUG THE PRINTER RIGHT NOW, IF YOU DO NOT ACCIDENTALLY DIE BY ELECTROCUTION!  I forgot and when I started unscrewing the first 6 screws, kept chime jump and im like * beep *? I was impressed by the security measures hp took as model engineering.

  (2) the printer is now disconnected and then go to your corner your work surface and place the printer, so there is a wall or a barrier on the left, and also, a wall or a fence behind it. This just in front of her as if you were about to use it.

  (3) now, what you have to do, is to open the printer as you will change the ink and on the right side, there is a plastic guide that prevents opening all the way to the top. Look on the side and you'll notice that he could jump off with fingers. pop off and open it completely open, so you can get to the screws of the cover you would have prevented access to.

  (4) press the scanner part and the upper part against the back wall.

  (5) all the screws you will be remove are the size T9H torx screws. There are ten total. There are 2 black screws in the top of the forehead and then 4 black screws in the top of the back. Remove them and put them on your paper plate.

  (6) following is 1 screw silver short located under the Control Panel, use your finger and feel under the * button. Unscrew, place it on the paper plate.

  (7) depending on whether you want to remove the face/Control Panel to get in the last 3 screws so locate the illustrations on the top of the printer, there are 2 on the lower left and 5 at the bottom right (1 and 2 on the left explain removals of paper jam and 1-5 on the right then explain change in ink cartridges). then about half an inch South of the illustration of the number 5 on the lip, is a plastic stand. six inches to the left is an another then 6 inches to the left, under the number of the illustration 2 (remove the paper jam) is a third support. Unscrew using your nails. Flip it up just like the hood of the car, and eten on the main top of the printer, keep the flat wire which is connected to the frame of the control panel (if the flat wire jumped because you got too loud, then simply insert it in when you go back).

  (8) then unscrew the 3 long silver screws that are located under the Panel you just popped off the coast. There is 1 on the left and 2 on the side rightish. mix 'em on the paper plate.

  (9) now that all the screws are removed, take the Panel front and partially pop it back together.

  (10) then take all over (the part with the small illustrations and lift like a hood of car, ONLY THIS TIME OPEN IT LEFT and he balanced on the edge of the printer, to lean over towards the wall or an obstacle on your left.) MAKE SURE NOT TO PULL ON THE STRIP OF COLORFUL SON FRUITS LEFT AND ALSO THE FLAT BLACK WIRE CONNECTING PART SCANNING FOR THE MAIN OF THE PRINTER PART.

  (11) then take the pliers to tapered spout and remove the 2 silver tension springs located behind the printer cartridges. Pay attention to where they were attached so you remember where they go during the Assembly. take a picture with your phone if you have to, or simply re - understand it like I did. mix 'em on the paper plate.

  (12) then disconnect the 2 large flat wire and 1 small flatwire attached to the back of the ink cart. take a picture or can remember like I did. I guess bad things can happen if you reverse the on re-Assembly. Pick up the phone and take a picture of quik to be sure.

  (13) now remove the cart ink, cartridges and all, by lifting the front first.  Be careful of the transparent tape little there that moves the carriage from left to right and vice versa. you don't want to damage this little guy. now take the transport to your paper plate. not some ink or accidentally get it on your fingers without knowing or will make a mess.

  (14) remove the ink cartridges and put them on the paper plate, side ink to avoid a mess, these things sometimes drip. put the plate side. its time to clean the print heads.

  (15) then go to the sink, to the distribution of empty ink and turn on the hot water and then let the transport of empty ink sitting there with the water mainly through the clogged color screen (inspect and make you is not a small rubber seal surrounding the small screen, if there is do not waste it. I didn't look too closely and I don't think that hp has them but I have a few other printers). It will stain the sink but water ink he comes out to be sure. notice there is also a small circuit attached to it. don't bang it upward but getting wet does not matter.

  (16) continue to do this until the water is clear.

  (17) then use your finger and rub the screen gently with your finger and then rinse it, taking ink until the water is clear. This continues until there is no more ink and screens are clean. do it for all the colors just for good measures. the color of problem that would not print, you'll notice takes longer to clean than the other colors.

  (18) now look on the lower side of the transport. these strange looking things are the leaders. Rinse in hot water and dry them with paper towels. then flip it over and the breath on the side of the screen again. also between the screenside and heads (on the side of the transport) is an opening which is also probably gunked up. It blows with water too. Then, turn it over and wipe the head again. Repeat this step until no fades or until you are sick and tired.

  (19) shake, then use paper towels to dry the entire unit. Make sure that the device is dry.  especially inside the female plugs. blow inside or out dry hair and dry gently. do not stand there and melt the but with the blow dryer. but the sooner it dries less your ink cartridges, sitting on the paper plate will dry out. the custom of the ink dry quickly just do not take a NAP or go on a date until you're back with part of the ink.

  (20) now you have finished cleaning the heads and probably don't need to do it again for the length of time, it was because you bought the printer. and just as a roadtrip you used a map to navigate, you will use these instructions in reverse for reassembly. but keep in mind when re - insert the 3 flatwires that you disconnected from the back of the ink cart, make sure you that have small metal contact on the flatwires points (side male) inserted so they affect small metal contact points on the caps of transport (feminine) side. ALSO BE VERY CAREFUL NOT TO DAMAGE BLACK FLATWIRE CONNECTING THE SCANNER PART PART HAND PRINTER. THERE IS A SMALL GROOVE IN THE PLASTIC WHERE IT CAN SIT TO GUARANTEE NO CRIMPAGE. USE IT. also make sure that the 2 hinges to the scanner portion/cover are placed correctly before the fixing of the top with the 6 black screws.

  now raise the printer and reinstall the ink cartridges. then plug in the appliance and turn it on.  If you get notifications on the control panel telling the custom of transport move, then open the trunk and remove the ink cartridges, hustles and ensure that transport is installed and that the tensioner springs are in place correctly. Repeat the operation if necessary until notifications go away or just do a test print and do not take into account the notification if you messed with it a few times already. That's what happened to me and the notification went his own. Once its online, open the hp utility and press the button "clean the heads. do 2 x in a row and you will be in style, with colors extremely rich and "BOLD" and Yes, printed black raven.

  p. s.

  You can always take your aggression out with tree limb loppers or Tin shears like I did and cut the plastic Center keeps you to transport directly outside. Completely eliminates the disassembly and reassembly. Make sure you DO NOT CUT THE TRANSPARENT TAPE THAT MOVES BACK AND FORTH TRANSPORT. This way the next time it happens it takes you only 10 minutes before you are upward and printing.

  Enjoy!  -Porf

• OfficeJet 4620: Cannot sweep to macOS 10.12 Sierra with Officejet 4620

  Since the update to Mac OS 10.12 Sierra, I am unable to scan using my Officejet 4620.

  I used to use the HP scanning software which worked well but I found out it only works with OS X 10.11 and earlier versions.

  The HP Easy Scan Soft says that it works with Mac OS or OS X 10.9 and later so I installed this.

  However, when the application is open there is a yellow explanation mark on the image of the scanner. The scanner is selected under the scanner drop-down.

  The printer works well, is that the scanning feature that does not work. I tried to reboot my laptop and printer and you have reinstalled all the drivers and application, but it still does not connect.

  Any ideas would be greatly appreciated!

  Thanks in advance

  Phil

  Hi Phil,
  The HP scanning application is indeed incompatible with Sierra, so you may experience problems.
  Remove the scanning HP by moving to the trash, then empty the trash, also remove all currently installed HP Easy Scan instances.
  
  Then install the latest version below, it will be installed in the Applications folder:
  http://FTP.HP.com/pub/softlib/software12/HP_Quick_Start/OSX/installations/Essentials/HP-easy-scan-1_7_0.pkg
  
  If you experience additional problems, ensure that the latest version of the software is installed by following HP Easy Start below:
  http://FTP.HP.com/pub/softlib/software12/HP_Quick_Start/OSX/applications/HP_Easy_Start.app.zip
  
  Finally, make sure that your drivers are up-to-date by clicking the Apple icon, select about this Mac and then press on software update.
  Click on the Bank on the menu bar, click Reload Page, click all update if an update is available.

  If you can meet with other issues, the printer is connected via USB or wireless?

  Kind regards
  Shlomi

• HP Officejet 4620: Printer is in"error" and will not print, even though the computer says that it is "connected".

  My printer recently started telling me it was in a State of 'error' and could not print my documents.  Sometimes I could turn off the printer market and all that was trying to print would then print, if documents or Quicken checks.  Now I can't print from the computer at all, or it will print checks from Quicken even if I turn the printer power off and power on.  The HP Web site indicates that it is connected.  It is the second computer from HP Officejet 4620 of the original that I bought.  The first has a problem that has been covered by the warranty, and this one doesn't seem to be much better.

  Hi @Janilynn,

  Welcome to the HP Forums!

  I read your post and wanted to help.

  I understand that the printer does not print when the computer shows that it is connected.  Please run the print and scan the doctor.

  I would like to know if it solved the problem or gives you an error message.

  If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me congratulations.

  Kind regards

• OfficeJet 4620: No number of scan

  My office is upgraded to this printer. My boss has the same printer. Its numbers of its analyses, one in our office does not work. Scans of numbering is what makes us buy this model.  Can I change the settings to automatically number the scans?

  Yes,

  The HP Officejet 4620 software press on scan a document or photo.

  Select the required analysis shortcut and click Advanced settings.

  Open the Destination folder, select the target folder and clear the check box to display the dialog box save as, then click OK and Scan.

  Later analysis is saved in the folder configured with automatic numbering.

  Kind regards

  Shlomi

• OfficeJet 4620: Installation

  I am trying to reinstall my printer but cannot read the installation disc.  Nowhere on the site Web HP find program drivers / Setup for this printer.

  Hello

  The printer software can be downloaded from the link below.

  http://support.HP.com/us-en/drivers/selfservice/HP-OfficeJet-4620-e-all-in-one-printer-series/5101229/model/5101234#Z7_3054ICK0K8UDA0AQC11TA930C7

• HP Officejet 4620: Office Windows 10 connects to the wireless network printer but do not print

  I have a HP Officejet 4620 all-in-one that I try to use with my desktop computer. The printer has been added to my home network, and I added the printer to my computer via the tab "Devices" Control Panel settings, but when I try to print, nothing happens. The printer icon appears in the bottom right of the task bar that says the printer has "0 documents pending. Strangely, another computer in the office at home, also running Windows 10, can connect and no problem printing to the printer. I tried to install/reinstall the drivers, reset my computer, reconnect with and without a cord USB, and none of this helps. Any ideas on how to solve the problem? My computer was running on Windows 7 until this month when I updated for Windows 10, so I don't know if it's part of the problem or not.

  Hi @leopleuridon,

  Welcome to the Forums of HP Support!

  I see that you are unable to print to your printer HP Officejet 4620. I'd be happy to help you with this. Looks like the driver is damaged.

  The software and the driver could have gotten corrupt, so we will need to remove it and reinstall.

  First of all. Please follow the steps in this guide:

  • HP printers - printer problems after upgrade to Windows 10
  • Run Windows updates, keep your computer current with updates for Windows.

  If the problem persists, follow these steps to see if you can solve the problem.
  Let's start by cleaning up your computer.

  • Cleaning disc in Windows 10.
  • Perform the clean boot in Windows 10 / 8 / 7.
  • Use the System File Checker tool to repair the missing or damaged system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  To properly remove the printer and drivers, follow the steps in this Post by my colleague @X-23.

  • I hope this helps. Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• OfficeJet 4620 analysis no or copy but no print

  My Officejet 4620 analysis no or copy but no print. The top is out, but I had reset (I hope). Unable to get above where take place tie scan and copy.

  Hello dbertentha,

  Welcome to the HP Forums.

  I see that you have a problem with scanning and make a copy.

  I see that you said that the upper part of the printer broke but you were able to get back on and now that is where the problem is happening with not being able to scan or copy.

  You are able to print, so we know that you have a communication between the printer and the computer.

  I do not think that this could be a hardware problem and if this is the case, we will then have to contact HP Total care.

  To contact HP Technical Support. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  Thank you for your time.

• HP Officejet 4620: HP 4620 cannot use recharged HP cartridges

  I can't use HP Officejet 4620 reloaded cartridges I bought at Costco. I don't know if it is because of the update of the firmware HP snuck in front of me.  If this is the problem is it possible to cancel the firmeare update?  I'm $50 such what.

  Costco reset chip cartridge to tell that they are full?  Costco install cartridges in a printer and check their operation?  If not, take back them and ask them to do.