OfficeJet 6500 all-in-one - black line down page

Similar Questions

• OfficeJet Pro X476DW: Scanner ADF black line down Page

  I had problems with scanning from ADF. There are two black lines coming to the bottom of the page on the scan. This does not happen when I scan directly on the glass through the bedfeed. I can't understand what needs to be cleaned or replaced. Help, please.

  Thank you.

  Hello and welcome to the HP support community!

  Open the lid of the dumpster and look at the extreme edge (usually the left edge, but it is where the paper feeds down).

  You will see a small glass to crack running the width of the flat glass.  Look inside this crack for a few pieces of paper/dust/something who lines up where the black lines are formed.  Use a can of compressed air or a brush to gently remove anything found.

  When using the document feeder, scanner actually itself parks under this tiny slit of a window and scan the document as it feeds on.

  I had this problem before on my OfficeJet Pro 8600 and found the solution here on the Forum.

  HTH,

  WyreNut

• OfficeJet Pro 8620: Scanner ADF black line down Page

  I followed the solution given on 03/06/16 to remove anything inside the slot of tiny glass. I still have the black line.  Is there anything else I can do? The glass can be removed for cleaning?

  Thanks for any help.

  The spec is likely on the top of the glass in the ADF, if on the underside, it would be out of focus.  I suggest a few things:

  • Use flashlight strong held almost parallel to the surface, it can highlight the area that must be cleaned.  Even a very small spec in the wrong place can cause a line on the output.
  • Copy a blank page through the ADF using 1-> 1 setting...  Now take the technique from the output tray and turn it 90 degrees to the left and place the sheet on the glass flat.  The line on the sheet will closely point to the area that must be cleaned thoroughly.

• ePrint HP Officejet 6500 All-in-One-Drucker - E709a

  Hello

  Is it possible to use ePrint with HP Officejet 6500 All-in-One-Drucker - E709a?

  Thanks Chris

  Hi Chris,

  The HP Officejet 6500 (e709a) does not support the HP ePrint service, that you will find listed in the following link:

  http://support.HP.com/us-en/document/c03722645

  Kind regards

  Shlomi

• Impossible to scan, fax, or copy of HP Officejet 6500 All-- E709a One in

  I can print from my HP Officejet 6500 All - in - One-E709a, but I can't scan, copy or fax.  All drivers and updates are underway; No recent updates have been made before the problems that occur. I use Windows 7 64-bit.  When the printer is turned on, it still shows Original charge, but no documents are in the charger or on the glass (I already cleaned the glass and have ensured that the lid is tightly).  I have problems to scan, copy and fax. The automatic document feeder works.  I tried to reset the printer several times.

  When I try to scan a document into the document feeder (it feeds through) or from the glass, I get varying answers - rarely, he asked well how I save/handle the doc (e.g., save them in pdf format), but the document does not actually scan and I'm headed to reload the document OR it displays no. Scanning Options. The document does not appear in my analysis.

  When I try to copy, it shows the document as copy, but there is a long delay before the progress bar occurs.  When I copy using the document feeder, I actually get a copy (rarely and always disappeared - looking) or copy prints white - two results are always followed by an error message to reload the document.  When you copy from the glass, the copy print in white with an error message to reload the document

  The same problems occur when you try to Fax.   If trying to scan, copy or fax, the printer does a lot of gears whirring noises.

  Again, I can print a document from my PC without any problem, the problem is limited to scanning, faxing and copying.

  I tried the doctor of printing & scanning HP.  It always stops at the HP Twain scanning stage, saying that the scanning process was cancelled by the user (not true).  When I click on continue, it proceeds to the stage of Test analysis, but nothing happens when I click the button of Scan Test.  It only will allow me to ignore at this point.   All the other steps show green checks.

  My first question is really going to reach the merits of the case, I heard you say that the printer produces noise, but if you lift the bar A) trip through the screen and the light cover B) up?

  In addition, perform both of these resets and I would like to know how they are!

  All-in-one HP printer reset - HP Officejet 6500 - YouTube'

  Have a great day!

• HP Officejet 6500 all-in-One Printer does not send scan and HP print and Scan doctor without help

  HP Officejet 6500 all-in - One Printer does not scan for Windows 7 and HP Print and Scan doctor says 'not imaging' & send error message 8, [1.0,-2147221498)] - I reconnected my officejet drivers reinstalled, etc & nothing works.  I looked for help & tried repeatedly, & am willing to renounce HP.

  Hello

  Thank you for using the HP Forums.

  You can try this alternative solution to Scan:

  HP extended Scan

  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi

  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.

  Let us know if it works.

• My HP Officejet 6500 all-in-one wireless suddenly stopped to print black, even if I have a lot I have

  My HP Officejet 6500 all-in-in-one wireless suddenly stopped printing black, even if I have a lot of ink. It prints all other colors. When I try to check the ink levels it tells me that this printer is not available, try again later. I have a lot of ink. Have restarted printer and Mac Book Pro. Driver is up-to-date. Any thoughts?

  Reset the printer.  Turn the power off and then hold the # and 6 keys during and shortly after turning it on.

• thin horizontal black line down page what scan on HP Officejet Pro 8600 more

  I've owned an HP Officejet Pro 8500 and scan was perfect.  I recently bought a HP Officejet Pro 8600 Plus.

  When I scan from the ADF HP 8600, I get a thin (several pixel wide) black along the lower edge of the analysis that results.  This line will be sometimes slightly twisted or appear only through half of the page, in which case, it tends to become thicker towards the edge of the page).  According to me, this line is an artifact of the analysis of the edge at the bottom of the original document.  I think it is to show where the bottom edge of the page was when parsing.  If the document is that a little offset, then the black line down will be a little twisted, probably following the edge of the page.  This issue is consistent and reproducible.  It is in the mode "Scan mail" and in mode 'Scan To Network Folder.

  When I scan from the flat bed, I get a very narrow black line along the side of the analysis resulting very superior, but the background seems in good condition (although I have not tested this widely).

  These fine black lines occurred when scanning the HP 8500.

  I wonder if there is a setting to adjust it, or if it is a firmware difference between printers needs debugging.

  Hey KenAlker,
  
  There are a few things I want to check if you have lines when scanning using the 8600. I see that mention you that lines appear both through ADF and flat glass. There may be something both of the glass sections used by this printer, but more often that otherwise, this isn't the case.
  
  I would check if the printer is connected to a surge protector. If this is the case, then try plugging the 8600 in a direct outlet. Often the surge protector can cause this problem appears because the printer has a built.
  
  Also, try a hard reset:
  * Unplug the unit while the
  Disconnect the other end of the wall socket direct
  * Wait 30-60 seconds
  * Plug the unit to the top
  
  Also, try to take a look at the steps in the document found here.
  
  I hope this helps.

• OfficeJet 6500 - flat scan creating black lines on output?

  Hi all

  I just bought an Officejet 6500 E709a Series and when I scan a document via the scanning to plate/sheet feeder tray, I get a number of black lines in the output? This problem exists when I use the flat and not the static mode of glass?

  Any ideas? Thanks for the help.

  http://support.HP.com/us-en/document/c01658811

  This article describes how to clean the glass Strip in the autoloader of documents (ADF)

• Will be A Officejet 6500 all-in-one printed my pictures from my camera using my sheets of Photo 4 x 6?

  Using Windows 7 64 bit and my all in one HP Officejet 6500 a can print photos from my camera on my HP 4 x 6 photo paper?

  The printer handle sheets of 4 x 6 because I do not see a photo paper tray I had in a previous HP printer all in one?

  Thank you for your help. Websites that recommend you explained what I needed to know.

• OfficeJet 6500 all-in-one: Digital Imaging Monitor

  Is it possible to install only the HP Digital Imaging Monitor for the all-in-one printer 6500.

  Or is it possible to find it on my computer.

  I did the complete basic installation and this is, but then I lost it.

  I had to do a full download / install drivers, who worked...

• HP Officejet 6500 All - in - One 709 a printhead printer resolution

  I want to thank Bob Headrick for his suggestion to soak the print head in warm water for 10 minutes.  It was a fantastic idea.  It does not solve the problem with my printer.

  I'm glad that I could help him.  For others looking for the solution for black not printing on the Officejet 6500 a, see the document here.  (Be sure to check the events on solution 6.)  If this does not resolve the problem then soak the printhead as shown in this post can help.

• OfficeJet Pro 8620: ADF Scan black line down

  Hello

  When I scan documents using the ADF, I get a black line at the bottom of each page (only the right side of the book). I tried to clean than the small scanning area - but I still get the black line - any idea how to get rid of him?

  You can download a sample scan pages virgins og here: https://files.secureserver.net/0s4RbMeFgHa3lX

  I just wanted you to day.

  After replacing the printer OfficeJet Pro unit 8620 3 times (when having tried 4) and I tried a HP Officejet Pro 276dw with the same problem, I ended up cancelling my order and get my money back.

• Can not reinstall the software/driver for the Officejet 6500 all-in-one

  I tried to 'day' the pilot on my all-in-one e710n-z printer 6500, and now I have no printer to work at all.  Installation stops at about 80% complete giving the error: Network Installation fails.  I followed all the procedures including online uninstall them, winsock reset, reinstall, install HP utility failure, disabled anti-anti-virus/firewall... nothing works.   My printer is detected by the computer and he "wants" install, but nothing works!  Wi - fi is on, and the only thing that I miss is the driver.  What is the secret of installing the HP online support site?  With the help of Windows OS 8.1.  Thanks for any help!

  Thank you so much for offering to help... This has been a very frustrating experience where I felt like I more, more was wrong.   It turns out that I solved the problem myself with a lot of trial and error and perseverance.  The location of the printer and our computers would not have allowed practical USB or ethernet connection tests.

  The computer has been grateful to the printer, but few of the functions of the printer did not work.  I kept getting notices that I need to be connected to Internet... and yet I was.   Instead, I followed every remedies proposed, and finally met and installed the HP Print & Scan Dr.   The full program would not even install, but I did use uninstall and reinstall the feature on the Dr. P & S and I noticed several MB difference between program he installed and which had been installed until then.

  The error kept showing a network connection problem, but I had already restarted the router several times.  When I got to the printer, I had loaded it a stable and permanent address through the router, so every time I "uninstalled and reinstalled then" software, it always by default the preset number on the router... that has been a blessing!  Finally, I got on the Web site of the real, connected and re-configured router the network connection on the printer using the PIN # that was generated (the WPS buttons had failed earlier) However, it happened, the resumed printer connected and I was able to print a test page.  All is well again.

• Cannot use the installer for Officejet 6500 all-in-one because of the resolution of the screen

  Hello

  I thought I could install my new Officejet 6500 as a printer network during the weekend, but apparently, HP had a different opinion...

  I use a netbook for my work as I travel a lot. Unfortunately, the screen resolution max available for these computers to wide screen is "limited" to 1024 x 576, which is less than the minimum required by the installation software (800 x 600), so I can't just install drivers and software. I tried to download the drivers from the HP support site, but ran into the same problem again.

  I'd appreciate any help I don't have a desktop or a laptop with a ratio of the 'normal' view and I'm stuck with a machine that is "useless"...

  Thanks a lot in advance!

  Yes. When you get to the window system requirements check, click the button cancel while now the keys Ctrl + Shift. It will bypass the sys. Req. check and continue with the installation. You may need to do this several times for the installation to continue.