Only the needs of the Cisco Aironet 1550 series a WLC?
Hello
Nice day. I would like to ask if the Cisco Aironet 1550 series requires a controller to run. Note that the references SKU in this fomat AIR-CAP1552E-A-K9-AIR-CAP1552EU-A-K9. I noticed that on the autonomous access point there they keyword 'SAP' on its SKU while the controller based has "CAP". If the
Cisco Aironet 1550 Series needs a controller which controller should it be associated? (e.g. AIR-CT2500)
Thank you
It can work stand-alone image:
1550 relies on:
2500, 7500, 5508, WISM2,... .etc
check the release notes of the code controller that you have and you should be able to identify what is supported and what is not supported.
----------------------------------------------------------------------------------------------
Please ensure good answers to rate
Tags: Cisco Wireless
Similar Questions
-
Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?
Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?
I have (2) AIR-SAP2602I-A-K9, configured the same way.
on two different remote LANs.
They don't seem to be handing out addresses via DHCP.
{If I connect to a local network with another DHCP server}
wireless devices can obtain addresses
This another DHCP server on the LAN through the access point.}
I followed 12.4.25d. JA.cg.pdf
Configuration of the Access Point to provide the Service DHCP 5-22
---------|---------|---------|
e.g. 3444-RCS1-AN #show running-config
Building configuration...
version 15.2
3444-RCS1-YEAR host name
no ip Routing
USH - DM IP domain name
DHCP excluded-address IP 192.168.29.89
IP dhcp RCS1 pool
network 192.168.29.88 255.255.255.248
router by default - 192.168.28.1
Rental 1 0
interface BVI1
IP 192.168.28.211 255.255.254.0
no ip route cache
default IP gateway - 192.168.28.1
---------|---------|---------|
---------|---------|---------|
e.g. 3444-RCS2-AN #show running-config
Building configuration...
version 15.2
3444-RCS2-YEAR host name
no ip Routing
USH - DM IP domain name
DHCP excluded-address IP 192.168.129.81
IP dhcp RCS2 pool
network 192.168.129.80 255.255.255.248
router by default - 192.168.128.1
Rental 2 0
interface BVI1
IP 192.168.128.171 255.255.254.0
no ip route cache
default IP gateway - 192.168.128.1
---------|---------|---------|
Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95
Well this will confuse your customers.
And this is NOT how to set up your "range". See below:
DHCP excluded-address IP 192.168.29.1 192.168.29.87
DHCP excluded-address IP 192.168.29.96 192.168.29.254
IP dhcp RCS1 pool
network 192.168.28.211 255.255.254.0
router by default - 192.168.28.1
Rental 1 0
-
Back on the cisco ASA 5500 series and PIX 500 series
Hello
I fund a site www http://www.searchsecurity.de/themenkanaele/plattformsicherheit/schwachstellenmanagement/allgemein/articles/106752/ (only in German). I have read that it is possible to make a denial of service on cisco PIX 500 series and series 5500 ASA, when the TTL value is enabled.
How can I check that? or solve the problem?
I thank you,
Mary
What version of the code you run the Pix or ASA. Refer to the "Products affected" section for more information on versions and the products concerned. This should point you in the right direction.
Also, listed in the URL is bypasses and fixed Versions that you may want to check.
Kind regards
Arul
-
Point of access Cisco Aironet 1200 series help
We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?
OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.
I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.
-
Update IOS Cisco Aironet 1200 series
I'm currently running;
C1200-k9w7 - mx.123 - 7.JA2
JA version 12.2 (8)
The search for certain documents or a list on the cisco site that shows the latest versions of IOS and if there is a newer version, I should look to use on them. Any advice would be appreciated.
Well, it seems that v12.3.8 is later if you have 1200
http://software.Cisco.com/download/release.html?mdfid=277026213&flowid=7...
Sent by Cisco Support technique iPhone App
-
Hello
I have a cisco aironet 1100 Series wireless access point.
by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.
I need your help please.
For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).
I downloaded the file c100-k9w7 - mx.123 - 8.jed
and I download the tftp (tftpd32) servers
I have the router connected directly to a pc with the static ip address of 10.0.0.2
but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.
and by a tftpd32 I try but no function.
I don't know what I'm doing wrong.
other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.
Thank you.
I'll wait your hepls.
Convert a standalone Lightweight Access Point
http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272 -
Cisco Aironet 1700 unsupported in the IP 2.1.1
Cisco Aironet 1700 is not supported in PI 2.1.1; no idea if there is an update in the roadmap?
Thank you
Go HERE.
*** Cisco AP701E is not supported by Prime Infrastructure 2.1.1. Also, Cisco Aironet 1700 Series Access Points are not supported by Prime Infrastructure until Prime Infrastructure Release 2.2, which is yet to be released.
2.2 IP's schedule release any time December 2014 or 2015 January.
-
Cisco Nexus 1000V Virtual Switch Module investment series in the Cisco Unified Computing System
Hi all
I read an article by Cisco entitled "Best practices in Deploying Cisco Nexus 1000V Switches Cisco UCS B and C Series series Cisco UCS Manager servers" http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9902/white_paper_c11-558242.htmlA lot of excellent information, but the section that intrigues me, has to do with the implementation of module of the VSM in the UCS. The article lists 4 options in order of preference, but does not provide details or the reasons underlying the recommendations. The options are the following:
============================================================================================================================================================
Option 1: VSM external to the Cisco Unified Computing System on the Cisco Nexus 1010In this scenario, the virtual environment management operations is accomplished in a method identical to existing environments not virtualized. With multiple instances on the Nexus 1010 VSM, multiple vCenter data centers can be supported.
============================================================================================================================================================Option 2: VSM outside the Cisco Unified Computing System on the Cisco Nexus 1000V series MEC
This model allows to centralize the management of virtual infrastructure, and proved to be very stable...
============================================================================================================================================================Option 3: VSM Outside the Cisco Unified Computing System on the VMware vSwitch
This model allows to isolate managed devices, and it migrates to the model of the device of the unit of Services virtual Cisco Nexus 1010. A possible concern here is the management and the operational model of the network between the MSM and VEM devices links.
============================================================================================================================================================Option 4: VSM Inside the Cisco Unified Computing System on the VMware vSwitch
This model was also stable in test deployments. A possible concern here is the management and the operational model of the network links between the MSM and VEM devices and switching infrastructure have doubles in your Cisco Unified Computing System.
============================================================================================================================================================As a beginner for both 100V Nexus and UCS, I hope someone can help me understand the configuration of these options and equally important to provide a more detailed explanation of each of the options and the resoning behind preferences (pro advantages and disadvantages).
Thank you
PradeepNo, they are different products. vASA will be a virtual version of our ASA device.
ASA is a complete recommended firewall.
-
Stand-alone configuration of Cisco Aironet 700i
Hello
I'm well aware new products Cisco. So please forgive my basic questions.
I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.
I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.
I use web access to configure the AP.
Help, please
Thank you
Sagar
Hi Sam,
Please check these messages to set up autonomous AP.
https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...
https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...
Concerning
Remember messages useful rates
-
Cisco Aironet 1830 disable broadcasting of the SSID
I recently bought a Cisco Aironet 1830 with the mobility Express version. installed 8.2.100.0. This unit is my controller and my only AP. I configured the device, but I can't seem to find a setting in the GUI or the CLI of the controller or AP disable broadcasting of the SSID. Can someone help with this?
Thank you
The CLI is available, the following command:
config ssid broadcast disable wlan
where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope. Ric
-
Cisco Aironet 1131AG and measure access points to the power of the wireless signal?
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}
We have about forty points of access Cisco Aironet 1131AG spread over four floors and they all have a static IP (BVI1) on the same SSID, customers will be on its own virtual local area network (dhcp on 3750 switch) and they use several channels (1,6,11). Cisco Wireless Control System is pending. This wireless network should support roaming for customers (there will be Wi - Fi tags of multiple AeroScout and wireless laptops). To measure the strength of the wireless signal and wireless coverage on each floor. My questions are:
- How to measure the strength of the wireless signal: we must meet at least three APs available with signal excellent (I guess for the WCS needs that will determine the position of the client in the building)? We thought to use NetStumbler and a few laptops with wifi and measure as many points as we can as simpler thing. Or should we use something like Cisco Aironet Client adapters for our mobile phone and then use Cisco Aironet Client Utility (is it worth buying for our analysis and measurement)? Any other idea?
- What signal level should we consider for a good wireless (dBm)?
- That we should propose for authentication, authorization and management accounting? What happens to the roaming wireless? I did not quiteunderstand WCS, WDS and WLC-that should be used for above tasks?
Thanks in advance.
"Use the command on the AP" sh dot11 associations "will give you the clients associated with success. If you add the MAC address of the client at the end of the command, you will get detailed information. Look under "Signal Strength" and "Signal to noise". Under the strength of the Signal, you want a value of-75 dBm or lower (lower values the better). -76 dBm and is bad. Under Signal-noise, you want a value of 25 dBm or more (values higher the better).
To measure the strength of the signal, I use Airmagnet, but you can use Netstumbler or Cisco Wireless Site Survey.
-
New Cisco Aironet 1602i is not broadcasting the SSID I place
New Cisco Aironet 1602i is not broadcasting the SSID I place
SSID I set up is not broadcasting, so I don't see the wireless network to choose and connect. On my laptop if I choose specify the name of the SSID then I am able to connect to the wireless network. I have only 1 Configuration SSID on the access point. Anyone know how to update the configuration for the SSID is broadcast?
The green light on the AP flashes and turns off about 3 seconds; is this normal or should it stays on all the time?
Current configuration: 1842 bytes
!
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
host ap name
!
!
Pulse 9 logging console
enable secret 5 $1$ rrlE$ msWqu8CGY/tpDkgRAAAIe /.
!
No aaa new-model
no ip Routing
no ip cef
!
!
!
dot11 syslog
!
dot11 ssid Mi Casa
open authentication
authentication-key wpa version2 management
WPA - psk ascii 7 142017070F0C787B7579
!
!
Crypto pki token removal timeout default 0
!
!
username Cisco privilege 15 password 7 112A1016141D
!
!
Bridge IRB
!
!
!
interface Dot11Radio0
no ip address
no ip route cache
!
encryption algorithms aes - ccm tkip encryption mode
!
SSID Mi Casa
!
gain of antenna 0
STBC
beamform ofdm
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 covering-disabled people
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
!
interface Dot11Radio1
no ip address
no ip route cache
!
encryption algorithms aes - ccm tkip encryption mode
!
SSID Mi Casa
!
gain of antenna 0
DFS block 3 Strip
STBC
beamform ofdm
channel SFR
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 covering-disabled people
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
!
interface GigabitEthernet0
no ip address
no ip route cache
automatic duplex
automatic speed
Bridge-Group 1
Bridge-Group 1 covering-disabled people
No source of bridge-Group 1-learning
!
interface BVI1
IP 192.168.10.200 255.255.255.0
no ip route cache
!
by default-gateway IP 192.168.10.1
IP forward-Protocol ND
IP http server
no ip http secure server
IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
1 channel ip bridge
!
!
!
Line con 0
line vty 0 4
local connection
transport of entry all
!
end
Hi you must guest mode config on the ssid... Read this bud
https://supportforums.Cisco.com/docs/doc-5442
Sent by Cisco Support technique iPhone App
-
Need help, reinstall XP Pro on OEM PC. Have only the product recovery CD.
Bought a PC PC Club in 2005. PC Club now out of business. Initially charged with operating system Windows XP Pro and other software is always on the PC, but only the last night recovery point is available. The PC crashes regularly and bluescreens. How should I proceed to a relocation of the existing XP Pro operating system? So far, resettlement has not attempted on the PC.
First, back up your important data on external media files.
Then, insert the product recovery CD as soon as you turn on the computer and follow the instructions it gives. You may need a BIOS setting to get the computer to boot from a CD.
-
HP Touchpad browser works only with the Cisco Valet Plus router
I bought a 16 GB HP Touchpad several months ago and had been enjoying his excellent WiFi feature with my old G from Linksys WRT54GS wireless router until I replaced it with a new Cisco Valet Plus (model M20) wireless-N Router a couple of days.
Although I could easily and successfully, join the Touchpad to the Cisco Valet network, browser fails most of the time to load web pages. For example, if I go to www.yahoo.com, the browser is going to slowly load the web page, or it will expire with a pop-up message error "Impossible to load the Page. If I try to select a link from the homepage of Yahoo, it expires with the same message. And this happens for all web pages. If the initial page happens at all, I can then from this page a link to any other.
I know that the issue is not with the router because I have several other devices connected to it and they are all working well, including a laptop HP ProBook, an iPad and a Wii Console, I use to watch Netflix movies on. None of them has a problem - only the Touchpad.
If I go into settings-> Wi - Fi, it shows that the Touchpad is connected to Cisco network. And when I run the diagnostic system, it shows that the Wi - Fi works correctly.
Does anyone have an idea how to solve this problem?
I have found a workaround that did the trick. I had to change the channel setting auto on a coded hard 1 channel wireless.
Now, the Touchpad works very well, as well as all other devices that have worked.
-
Are all the tools you need to configure an Aironet 1242AG?
I keep getting messages that my access point refusal to connect.
I put on the same switch that I'm connected to (a C2960). I can see it get an IP address, I can ping, but I get a refusal on the web address. The fact that the said refusal to connect browser I think it's a permissions problem.
I have the Cisco IPSU tool and when I entered the MAC it finds the IP address. I checked on the DHCP server. Shouldn't be able to hit the web interface of the access point by using the IP address that has been assigned? Am I missing something?
My laptop is not a serial port so I'm a bit limited here. Any help would be appreciated!
You must enter AP CLI to check/troubleshoot your configuration.
You can use USB-serial cable to get access to the console, if you have only USB ports on your laptop
HTH
Rasika
Maybe you are looking for
-
Am I the only one to have a problem with the zoom is constantly disabling feature?
Running iOS on a 6Plus 9.3.3, I continue to turn on zoom and nearly every day he himself turns OFF. Am I the only one experiencing this bug?
-
Satellite A200-14F (PSAEC): XP driver links do not work
I want to install Windows XP on my laptop.I went to the download page and he gave me a number of xp for my A200 drivers, but the links do not work.where can I get the drivers?
-
In Outlook Express, there is no longer a noise when I get an email.
AT OE. Recently, I lost the sound for incoming mail. Have tried to reset but nothing seems to work. Any ssuggestions, please?
-
B &; w threshold too low when scanning
HP DeskJet F4135 printer range: when you scan pages in a pdf file, the b/w line is still too low. I need to reset for each page that takes a long time. Any way to adjust the threshold of b/w once for all pages?
-
Como CFFO para instalar minha impressora again as faith desinstalada com o problema as deu no laptop