Only to the network on SAA

Similar Questions

• Local access only after the Network Systems Security 2009 malware removed

  I'll try to put all the details that I can here, but my laptop that has the problem cannot connect to the Internet so I won't be able to copy paste n info. Last week, I was struck with the 2009 malware security systems. It was a pain to remove because it stopped all the work programmes and I could not install malware removal software. Finally beat him by renaming the main program folder 2009 for the security of the systems. That he has stopped working when I restarted the laptop and then I was able to install the malware removal software and took remoped.

  Here is the problem. Now that he is gone my network connections wireless and wired no longer work. I get local access only on an unidentified network. I have Windows vista Home premium and use internet with a modem model Cableone cable Motorola Surfboard SB5101.

  Then I called a cable tech support first and they could not help and after all the service works very well on my desktop the same modem and connection. So I called Motorola tech support and they had me do a lot of things for hours (including reinstalling the drivers for the modem) on the phone without effect. Finally, they suggested that I have re-download all ACER Aspirion z9410z drivers and reinstall them. So I did it. Copied to a flash of my desktop drive and reinstalled them. No luck.

  The respectable and sharing Centre, explains that the modem works correctly when you look at the status. But the auto for windows diagnostic tool says to check the IP settings automatically and reset the network card. The two fail to trouble when ran. Here are all the parameters of the network connection.

  Physical address: 00-1A - 66 - AA - 64cB
  Active Yes DHCP
  Autoconfiguration IPV4 address 169.254.195.250
  IPv4 mask subnet 255.255.0.0
  Net Bios on active TCP/IP Yes
  Link-local IPV6 address fe80::1878:12 d 5: a566:c3fa % 36
  Servers of DNS IPv6 fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
                                                  
  IPv4 and 6 are defined automatically detect the IP address and the DNS.

  Hope that gives enough information. There no mater if I use eithernet and USB to connect or wireless. I have the same problems.

  Another thing that can be part of the problem.

  It started after removing the systems security 2009 malware as well.

  When loggin, turned off the laptop, a blue error screen appears. Here are the details generated for it. I'm working on the research of which the question is to be set by the online search.

  Event name BlueScreen
  OS version 6.0.6000.2.0.0.768.3
  local ID 1033
  BCCODE one
  BCP1 00000016
  BCP2 0000001 B
  BCP3 00000000
  BCP4 82028768
  OS version 6_0_6000
  Service Pack 0_0
  product 768_1

  I hope I will get this fix as well.

  Any help will be greatly apprieciated. If more information is required only, let me know and I'll get it.

  Thank you all.
  Jason

  Hello Oxilas,

  I suggest that you use a friend/co-worker Vista DVD and do a repair installation.

  Repair facility:

  You can reinstall your copy of Vista while keeping your files, settings and programs by performing a repair install or an upgrade on the spot with the following steps: (Note: this still does not resolve all problems, especially if the corruption was caused by a 3rd party program or service, you may need to do a clean install) (if this is not successful.)

  <><><><><><><><><><><><>

  Please make sure that you back up all the important data before you continue. Please visit: methods for your backup files.

  Always make sure that you have the means to reinstall your programs, or by an installation disc or access to the installation files.

  <><><><><><><><><><><><>

  1. Insert the Windows installation disc in your computer's DVD or CD drive. You must start Windows installation while running your existing version of Windows.

  2. on the Install Windows page, click install now.

  3. on the get updates for installation page, we recommend getting the latest updates to help ensure a successful installation and to help protect your computer against security threats. You will need an Internet connection to get the installation updates.

  4. on the Type your product key for activation , we strongly recommend that you type your 25-character product key in order to avoid problems during activation.

  5. on the page Please read the terms of the license , if you accept the license terms, click I accept the terms of the license.

  6. to the which type of installation you want? page, click upgrade to begin the upgrade. You can see a compatibility report.

  7 follow the instructions.

  Note: If your installation disc doesn't include SP1, and you are updated, then you must uninstall it before proceeding with an update install. Start-> Control Panel-> programs-> see installed updates, then select Service Pack for Microsoft Windows and click on Uninstall.

  Note: Tit the following settings is reset by default:

  Its computer system

  Device drivers

  Visual effects

  Windows Mail

  Windows services

  If you notice missing files after the upgrade, look in the following folders:

  C:\Windows.old

  C:\$INPLACE.~TR

  C:\$WINDOWS.~Q

  These files can be eliminated with disk cleanup as "records destroyed by upgrade to Windows".

  Delete files using disk cleanup

  Thank you for using answers Forum. Please let us know how it works.

  Joseph
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Files read-only on the network.

  Hello.  I use Windows 7 Pro 64 bit.  I have a home network with a second computer (Win XP pro) configuration.  My problem with my Windows 7 computer.  I can create and modify files it contains very well.  However when I access those files on the network, EITHER from the 2nd computer the same computer (which is connected to the computer 1, from computer1, via the network) they open read-only.  The curious symptom is that the files are read-only even when I connect to computer 1 to Computer1.  Any thoughts on this problem?

  -Files are not selected in their properties read-only.

  -There is only 1 account for both computers on the network, and this user is a member of the Administrators group.

  -This happens for all files.  I found an article about a known problem similar to Excel files.  I followed the instructions in this article, does not.

  -What happens when the files are located in C:\temp, C:\Users\\Desktop\temp and Documents C:\Users\Public\Public (supposed to be a shared folder).

  Any help would be great.

  Hello

  Check the authorization/security.

  Problems of permission and security with Vista/Win7, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  * Note . All the users who are allowed to share need to have an account on the computers they are allowed to connect to everyone is an account, that means a group of all users who already have an account now as users. This does not mean everyone who feel they would like to connect.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Is there anyway to preconfigure a network printer (for example, a printer attached to a server that provides a DNS naming convention) without being on the network provided for this resource? In other words, you can set up a printer network offline?

  I need to preconfigure laptops before they never connect to a network because only when the network is located compared to myselfd.

  Hello NicePerson,

  Thank you for your message.  Since that a network printer, you can print to this printer from where you are now?  If you can print to the printer you are, then you should be able to add the printer from your location via TCP/IP.  The steps are:
  Click "Start" > click on "printers and faxes".
  Click on "add a printer".
  Click on "Next" > ensure that only "Local printer attached to this computer" is checked, the other two inputs must remain empty.  Click "next".
  Click on "Create a new port" > use the drop down arrow to select "Standard TCP/IP Port" > click "next".
  Click "next".
  Type the correct IP address of the printer and complete the wizard by installing the drivers, etc..
  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Site to Site VPN will not be forwarded to individual hosts, only of the whole networks

  I have a VPN site-to-site built between a Cisco 1750 router and an ASA 5555 X running 5 9.2 (4)

  There is no problem with the change sets, key exchange. However, I noticed that the ACL that is used to create the field of encryption on the SAA does not work correctly if the network on the 1750 is compared to the individual hosts on the SAA.

  Example of

  permit access-list extended access acme ip 172.25.91.64 255.255.255.224 host 192.168.10.24

  on the SAA where 192.168.10.24 is the remote host and 17.25.91.64 27 is protected behind the ASA network. If the 192.168.10.24 host tries to ping 172.25.91.70, I see the tunnel begin to form on the ASA and then fail with a message "failed policy."

  If I go the other way around, the 172.25.91.70 host to 192.168.10.24, the tunnel is built and traffic is allowed.

  If I change the ACL to use only the network address (in other words, use 192.168.10.0/24), it works in two ways.

  What happens here? If I use a group of objects instead of individual hosts directly going to work? Not sure why it's a failure.

  It depends on the implementation of the provider.

  Using the baseline IPSEC policy, the networks of each side must match. Filtering in the tunnel does not rely on the establishment of a tunnel, one can be a host or a subnet.

• Using too much CPU only when loading the network

  When FF works closely with the network (wired or wireless) card for access to the network, CPU utilization spikes in way more than 70% and he stayed there until the page loading process finishes web.
  After the upload is complete, the CPU usage remains somewhere between 5-10%.

  When I look at clips youtube 1080 p, where FF is duty next buffer part of this clip I watch, new CPU use peaks above 70% with the flash plugin and gives a total of a 100% of cpu for a few moments and use which make this clip to stop playing or to frame bad times, and ties.

  I have been activated in about: config webgl acceleration to activate the force and that much improve the initial problem, then I activated gfx.direct2D - activated force and also to improve the problem remaining.
  I also disable the safe_mode parameter file adobe flash config protectedmode = 0.

  I have to mention that the initial problem was way to bad ... 
  

  Now I get to point when I don't know what to do so that FF does not use much CPU loading pages.
  As you can see I use to publish this version of Nightly 64 bit (I think it's the 64-bit version...) which is much more better and I would like to read youtube 1080 p clip normally, after that I have wait a few moments to buffer, before starting to play.
  Version 32 bit FF won't let me watch YouTube without framing hurt when the clip is buffered.

  I was monitoring the Task Manager and all the processes listed... and there, I can't blame antivirus or firewall to the peaks of the processor. Also if I do the rest of the network traffic, as well as inside the network custom CPU even file copy flinch.

  Can someone help or give an opinion on what setting to do, so I can eliminate these spikes?

  Thanks in advance!

  Problem solved partially:

  I have observed that the CPU spikes occur not only while I use FF or mozilla nightly, but on all web browsers (Chrome, IE, Opera, etc) that I have used, while these browsers accessing the network.

  Uninstalling the firewall of the solution of the AV portion has helped a lot and by also disabling the bed in the firewall solution of W7, but for long term use, this isn't the right answer (for my at least). Without any firewall FF work or installed works like a charm, while the CPU usage is increased at a decent level of 50% max (total tasks and running services)!

  Anyway, as I said earlier, my pc without any firewall operation is not a good think to do, so I'll replace my computer with a faster, or I'm going to overclock it at a level that zapping INTERNET and navigation will not infringe too much on the performance of the system, or... I live whit it and I accept the limitations...

  Perhaps, in the development of the FF, programmers will keep in mind that not everyone on this planet has powerful processors - and... give a few options... to decrease the CPU at acceptable levels, event, even if they use the firewall solutions that violate on the CPU while FF is buffering of data across the network.

  I should also mention that Mozilla nightly (64-bit) and FF, are always better then IE - in my opinion - which is.

• My new airport does not detect my existing WiFi network, I can connect only via the LAN.

  Bought a new airport 1 TB TimeCapsule and I wanted to add to my existing via a WLAN network. It does not detect it and I can connect only via the LAN. What I am doing wrong?

  Unfortunately, unable to connect to a 3rd time Capsule part wireless using a Wi - Fi.

  You need to connect to the time Capsule to your existing modem/router using a wired Ethernet cable connection, permanent... like the Time Capsule Setup Guide illustrates.

  

  If you really don't want the time Capsule to connect using the wireless... she can do... If it gets a signal to another Apple wireless router. So if you were ready to add another Apple... as an AirPort Extreme router... and connect it to your existing Ethernet cable router/modem and configure AirPort Extreme to broadcast a wireless signal... .then.. .the Time Capsule would be able to connect in this way, assuming that he is where he can receive a good quality of AirPort Extreme wireless signal.

• Omen of HP 15: Wifi stop working. Win10 shows only a single network and it connects to the WiFi

  Hi guys,.
  Since a few days my wifi stopped working.
  If I click the Wifi icon it shows only a SINGLE NETWORK (two maximum), but not mine!

  

  And I live in a building of 20 + networks, as you can see on the WiFi Analyzer (I'm the only red to the right)
  
  
  
  If I reactive / disable Wifi with fn + f12, it goes back in plane and Wifi mode mode and sees it eventually all networks:
  
  
  
  My Wifi is on top. If it is registered, Windows connects to it and then she abandons the connection; If it is not registered, and I try to connect, it says "you are not able to connect to this network.
  Is fun is that after a few seconds, each network disappears and alone is shown (probably the one next door... I don't know).
  
  I already tried to RESET the laptop MATERIAL by keeping the power button for 10-15 seconds with the laptop is turned off.
  I tried to follow these instructions (http://support.hp.com/us-en/document/c04649175) updated drivers (Intel 18.12.0.3, 18.12.1.2, 18.30.0.9 [10 default Windows], 18.32.0 [last drivers]) without success. Whenever I have install a new driver, I uninstalled the earlier software Wireless + restart.
  
  I tried to uncheked "allow this computer to turn off this device to save power" on my settings of Wifi hardware without success.
  
  HP network support said that I did not choose a Wifi (really? The problem is that I do not see my Wifi on the list!).

  This is unrelated to a new 10 Windows upgrade since I installed it months ago and this is the first time I have this problem :/ It has always worked
  
  I tried different settings too:
  I changed the channel, I put 802.11 g on my router, APSD off on the router.
  I put "Magic off packet, QoS ad hoc off, U-APSD off, fat wide channel, differential flow mode HT off" on the creation of the map without success. Nothing chaned.
  
  The hardware test detects any failure.
  
  Important note: If I close the router, it shows my network connection with full power and he connects to it. Then I come back in my room (probably 3/4 meters away), it MAINTAINS the connection for 30 / 40 min and he drops the connection and I cannot reconnect to it more. It has always worked perfectly in my room during these months (I bought it in March 2015), so the distance is not a problem, I'm 6 / 7 m away from the router.
  In this case, it shows my network (connected) and the nearby... and the other 20 networks +?
  
  The only way I have is USB tethering with my Nexus 5.
  
  Linux: I tried the WiFi on Freya elementary (Ubuntu linux OS base) and it displays 20 + networks available on the list. He has not the connection problem with my Wifi, but sometimes it stops working, Web pages stop loading and I have to restart Wifi to reconnect to the it (usually after 30/40 min of use it).
  
  -------------------------------------------------------------------------------------

  What is the problem? My Wifi card is broken? Should I call Italian support or if you have any suggestions?

  WAWood,
  I took a risk.
  I did a factory restore with recovery HP (I have a drive dedicated for her)... and it worked!
  I had to switch from Win8.1 to 10, but the Wifi problem is solved!
  
  I'm still guessing that was the problem...

  Now, I'm under Intel drivers 18.30.0.9 worm and all the networks work.
  
  In the next few days I'm checking the linux problem (reset deleted primary partition).

• I ONLY see comments on the network of the time machine?

  I've implemented a Time Machine Network, adding a TP link Extender to get signal from my office where the router from BT's home. I also checked the comments option and also the hidden network too in the House, however I don't see the option comments - what Sky does not recognize.

  What Hat I did wrong?  I have a spare homehub5 BT - can I use it as a spare router in the House to boost signal more?

  any help much appreciated!

  AJ

  Basically, the 'Comments Networking' function only works with Apple mobile networks. You cannot extend this network with a non-Apple as your TPLink device.

  In your case, you would need another time Capsule or AirPort Extreme to extend the network of comments.

• How to share a folder in windows XP with password so that people on the network can see only its folder

  Original title: Network share

  How to share a folder in windows XP with password so that people on the network can see only its folder

  Hello

  See the following article:

  How to disable the file sharing simple and how to set permissions on a shared folder in Windows XP:

  http://support.Microsoft.com/kb/307874

• Error read-only during the Windows XP networking with a Windows Vista-based computer

  Help, please.  We have set up a working group, the destop with Windows XP behaves as the server and laptop with Windows Vista is the other computer.

  We can share and open all files.

  The problem is with a mortgage loan software. (Chalice)  On the Vista computer, when you try to open a file, we get the error "the file is used by someone else.  You want to open the file in read-only Mode? "We have worked with their Tech Support who insists on the fact that it's a Microsoft set up the problem with the server computer.  In their diagnosis, they say that the cause may be "the server has locked files or you don't have full access to the records.  Their Technical Support remotely connected to our two computers and verified that we have the network set in place correctly-"everyone" has full control of the files.  Both computers have disabled the Windows Firewall.  How can I check if the file is locked by the server?  And why would he block specifically for mortgage loan software?  Any other troubleshooting help would be most appreciated.  They have guaranteed that this software can run on both Windows XP Vista computers & a set.

  Another question - when I right click on the folder that this error message, and then click Properties, on the general tab, attributes, the 'Read only' box is populated with a solid green box.  It can also be a check mark or a cache.  I deleted the solid green box and tick, apply settings, but still no luck.  What is the difference between the solid green box and the checkbox for that?

  Thank you to those who can help - we are really at a loss!

  Edit:

  Additional info - The Windows XP computer using IE 8, 32-bit, Windows XP, Media, 2002 Edition, SP3.

  The Windows Vista-based computer uses Vista Home Premium SP2, IE 8, 32-bit Edition.

  Hello

  I suggest you to send your request in the below link.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Not set to read only on the files so that they can be shared and changed on a network.

  I've seen any other questions on this subject, but they do not solve my problem.  I had to reset my network because I have a new router.  Now I can open the files on my main computer from another computer, but they always opened read-only.  I tried to set sharing and security to allow the share on the network and allow network users to change files.  But I can not turn off the box next to 'read only' in the general tab.  I also tried to start XP in safe mode and take possession of the file (article 308421), but this does not work either.

  I also tried in vain to change the attributes of command line to remove the read-only attribute and to set the system attribute, use the following command:

  attrib - r + s drive:------------

  After trying a few other corrections, I finally did a system restore before the installation of the network.  Then, I used the Network Wizard to reconfigure the network. I changed the name of the computer, so I knew what was the new connection.  Then I copied the wizard network on a USB key and reconfigured the second computer.  Now everything works fine (I can open, edit and save files between computers) even if the readonly attribute is always highlighted on the record.

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Unable to connect to wireless internet; can only connect to the network, saying "Local only" or "limited connectivity".

  I have problems to connect to any wireless internet - home, library, coffee shops.  He used to work, began to get in trouble (i.e. could not connect sometimes to the diner, but works in the library) and now does not connect to internet AT ALL wireless.

  Only connects to the network saying "local only".  And I'm lucky even get that much.  Furthermore, I don't know if it's a router problem or what, but it does not even accept the password for my home network (my boyfriend has no problem on the internet with Windows 7 and the current router password).

  I use a HP G60 laptop (maybe?), I don't remember the model exactly.  Windows Vista.  I am frustrated beyond belief.  I took the computer to Best Buy and the man suggested that contact Microsoft because, in his own words, "this seems to be a very common problem with the adapter wireless in Windows Vista".

  In summary: is it a hardware or a software problem?  It seems to be a software problem that can have an impact on the material.  Nevertheless, what can I do to fix this?  Y at - it a software update, I need to try for my wireless card?

  This computer is not yet a year old, and already I am unable to use it for the internet.  Not very well I plug my ethernet cable router wireless in the library.  I bought a laptop for a reason, but it is on track to achieve more like a desktop.  Very disappointing.

  Someone, please help!

  I took the computer to Best Buy and the man suggested that contact Microsoft because, in his own words, "this seems to be a very common problem with the adapter wireless in Windows Vista".

  Is this a hardware or a software problem?  It seems to be a software problem that can have an impact on the material.  Nevertheless, what can I do to fix this?  Y at - it a software update, I need to try for my wireless card?

  Hello

  When the man from BestBuy, fortunately for us technology is not a cleaning product, there is no way of knowing if someone puts his hand on it and knowing what is wrong rather than moving oral reprimand...

  First step, log on to the HP support and download the latest drivers for your wireless card.

  The HPG60 is a very good phone but its wireless card has problems with old drivers.

  In which case it's a hardware problem, contact HP support.

  In general, you can use this process to find out what's wrong with the wireless.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Computer connects to the network, but not to the Internet, connect to the only local

  Hello world

  OK, so I have a HP computer with the installed version of Windows Vista Home Premium 32-bit. I've had it for almost 2 years now and have had no problems connecting to Internet... until now.

  I can connect to networks... both wireless and cable, but I can not get Internet. I used the IP, subnet mask, gateway and server settings DNS to another computer that works with this specific local network just to see what happens... my computer has failed.
  Until recently, I could connect to this WiFi connection in a coffee shop, but the last time I tried it didn't work. I've connected to the network but not the Internet. He told me that the DNS server did not. I'm starting to think that something is wrong with my computer.

  I saw that the solution for some people running the Norton removal tool, however I had uninstalled Norton almost as soon as I got my computer 2 years ago and ran McAfee instead. I don't think that Norton should have an impact on me more.

  Is there a solution to this problem... or I'll just have to try everything that is out there?

  Thanks for your help!

  Hi MomPlaysBass,

  Finally, my problem has been resolved - it wasn't my computer after all. The modem may only be connected to a computer. If you want to connect to another computer, you can connect the computer to the modem and then put it back. My computer worked fine after that. Whenever we want to switch between computers, even if I have to reset the modem.

  I don't think you have the same problem, but just in case, you can try to reset your modem - it's a button on the back or a small hole that you can reach with a pen... Hold the stylus for about 5 sec or maybe a bit more and then let go. That should reset your modem and might help you with your problem. Your computer should also have created a restore point... If all else fails maybe you can try to get back to the final point where your computer worked.