OnPlus discovery and Nexus 5548
Hello
I just installed an OnPlus agent for a customer who has a Nexus with a 3 layer daugthter card 5548 as their central switch, but the agent is not discovered any device beyond the vlan in which he is sitting. Does anyone have any experience with the OnPlus ageent and Nexus switches. It is obviously not a Cisco device supported but I configured IDs connection and snmp access to the switch on the portal, but still nothing is discovered. Any advice greatly appreciated.
Concerning
Ian
Hi Ian,
To discover the multi - VLAN, connect the On100 to an 802. 1 q trunk port. This will allow the On100 discover other VLANs. It is currently connected to an access port which is to limit the broadcast traffic of the other VLAN.
Although the device is not currently supported, he discovered and enable basic support we provide for all detected devices.
Thank you
The OnPlus team
Tags: Cisco Support
Similar Questions
-
Connectivity problem between Nexus 5548 to VNX 5300
Hi all
I'm a lab facility where I want to connect Nexus 5548 UP to 5300 VNX storage directly. Physical connectivity is established between the switch and the storage, but the Nexus, the port State shows "linkFailure". I've tried corresponding to the port (such as self, F) mode and the speed but the port still says "linkFailure".
Connectivity between Nexus and VNX is CF.
Someone may suggest the cause or the troubleshooting steps.
Kind regards
AFA
LinkFailure could be a GUI status.
might show interface fcx/y say.
Failure to bind or not connected
The physical layer link is not operational.
This means that the switch does not detect the light, so the phyiscal layer is the cable and lasers (sfp, HBA or other adapter uses the VNX). This could mean that you have to turn the interfaace to the top of the side vnx.
-
Hi all
I have problems with the ports of 1000Go Nexus 5548 ports. They go down once a while with the error "connection not connected" while the links are connected. When I move the connections to other ports, they work, but after a while the thumbs down with the same error. I can confirm it is currently down worked and its currently connected. Has anyone seen the error before?
Please see the output of the interface that evolves down below:
Sho VNX_NEXUS # interface eth1/11
Ethernet1/11 is down (not connected link)
Material: 1000/10000 Ethernet, address: 002a.6a71.1f92 (bia 002a.6a71.1f92)
Description: Link_to_EMC_RPA3
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
Auto-recto-sided, 1000 Mbps, media type is 10G
Lighthouse is off
Input stream control is turned off, output flow control is disabled
Flow mode is dedicated
Switchport monitor is off
EtherType is 0 x 8100
Last link flapped 2d23h
Last clearing of "show interface" counters 5w6d
entry 30 seconds 0 bps, 0 packets/s rate
exit rate of 30 seconds 0 bps, 0 packets/s
Load-time #2: 5 minutes (300 seconds)
heat flow 0 bit/s, 0 pps; output rate 0 bps, 0 pps
RX
43384443 30 packs 1496 multicasts packets broadcast unicast packets
packages of entry 43385969 7837558138 bytes
0 bytes removing storm Jumbo packets 0
Giants of Runts 0 0 0 CRC 0 no buffer
short entry error 0 0 0 overflow under-run 0 0 ignored
0 0 bad etype watchdog fall 0 bad proto place 0 if drop
0 entry with dribble 0 rejection of entry
Rx pause 0
TX
56587244 packet 3937125 packets 1487058 multicasts packets unicast broadcast
62011427 packets output, 14141808286 bytes
0 jumbo packets
collision of errors 0 0 released 0 postponed end collision 0
0 lost carrier 0 no 0 0 output babble carrier throw
Tx break 0
18 interface resetsLast link flapped 2d23h 18 interface resets
You have a failure of the line.
-
Network discovery and public networks
I turned on "Network discovery" and he asked if I wanted it on public networks. Without thinking, I clicked OK and now I can not understand how to return a change it to private networks.
Help.
Click Customize and change your network to a public network. Stop 'Discovery network' and then turn it on again. Boulder computer Maven
Most Microsoft Valuable Professional -
Network discovery and file sharing will not stay
The bar notification on the screen of the network in Windows explore said that discovery of the network and file sharing are turned off and click to change. After a right-click and by turning on the network discovery and file sharing, the notification bar appears again and said the same thing.
I have ensured that the services are running, and appears not to have solved things. I am able to ping other computers that I know are on the network.
I didn't have this problem until a few days ago, and the strange thing is that I am able to access other computers on the local network via the \\computername method. However, access my computer from other computers or devices miss you
Any help would be greatly appreciated. Thanks in advance.
I realized that guys on my network have not been able to ping - me, so I did this:
http://superuser.com/questions/375100/what-happened-to-my-predefined-rules-in-Windows-Firewall-how-can-i-get-them-b
I activated adding predfined advanced and enabled firewall rules all incoming and outgoing in the file and printer sharing. Now, everything works fine.
-
Cannot depend on the network discovery and streaming media
I use Win7 Pro., SP1.
Some time ago, the I realized that I can not use home network more. I can't turn on my discovery of home network and streaming media. The network discivery always returns OFF.
The following services are all on (automatic): support TCP/IP NetBios and DNS Client, Function Discovery Resource Publication, SSDP Discovery.
Please notify.
Hello Dudi,
I would like to know some information about the problem so that we can help you better.
What is the brand and model of your computer?
Thank you for details on the question and your efforts to resolve.
I also know that the inconvenience that you are experiencing because of the discovery of the network and streaming media problems. I'm going to
certainly will help.
Network discovery is a network setting that determines if your computer can find other computers and devices on the network and whether other computers on the network can find your computer.
This problem can occur because of incorrect network discovery and streaming media settings.
For network discovery, I suggest you use the steps in this article and check if it helps.
Reference:
You can't turn on the discovery of network and Sharing Center in Windows Server 2008, Windows Server 2008 R2 or Windows Server 2012
https://support.Microsoft.com/en-us/KB/2722035
(Also valid for Windows 7)For media streaming, refer to the suggestions of gifted xI replied on 24 December 2010 and check.
http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-turn-on-media-streaming-another-Windows-7/b765ec7a-8c7a-4147-8645-fedc3a5fc991I hope this information helps.
Please let us know if you need more help.
Thank you
-
HW SW INFO:
UCS B200MII
Nexus 5K
PVS 7.1
7.1 XD
http://support.Citrix.com/article/CTX123158
According to this link, I need to enable portfast and disable bpdguard in Cisco and Nexus
My friend argument, no need to enable the portfast because pvs and vm win7 all using vnic, which there is no user disconnect nic physical port.
Is this true?
If set to false then can I globally enable portfast and disable bpdguard on base sw and nexus
Thank you
Sorry, I wasn't clear, see below
Q1. no need to activate the portfast because pvs and vm win7 all using vnic
A. your answer is Yes, it means without having to enable portfast
Yes, but if you do, it does nothing
I am referring only to the network between UCS fabric interconnection and N5k
See, for example. https://supportforums.Cisco.com/thread/2070841
There is no tree cover in UCS EHM run below your uplinks, so you can use Port Fast safely.
PortFast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to this interface when the portfast is enabled, may cause temporary bridges loops.
Please see for establishing a vpc
Q2. I have in the world, enable portfast and disable bpdguard on base sw and nexus
According to my interpretation, without having to enable portfast global and disable bpdguard on base sw and nexus
Is your overall question or interface? I would certainly by interface.
How can I check that end host in FI mode is used or not?
This is the default value.
-
cannot depend on a file of discovery and sharing files and printing
I know this has been posted before but I can't find the right answer, I tried all of the suggestions I've found. I still can't file discovery and sharing files and printing to stay on, I use Norton firewall and I always turn off no luck. Have you checked all the services which are expected to be running and that they have tried the suggestion to try it in safe mode still nothing did nothing a sfc/scannow. I am using windows 7 pro 32 bit summer trying to figure this out for a week. I'm trying to do not have to reinstall windows.
Thanks for any help
I know this has been posted before but I can't find the right answer, I tried all of the suggestions I've found. I still can't file discovery and sharing files and printing to stay on, I use Norton firewall and I always turn off no luck. Have you checked all the services which are expected to be running and that they have tried the suggestion to try it in safe mode still nothing did nothing a sfc/scannow. I am using windows 7 pro 32 bit summer trying to figure this out for a week. I'm trying to do not have to reinstall windows.
Thanks for any help
Already responded to check if this may correct your answer
http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-turn-on-my-network-discovery-and-file-and/9e766e4b-3eb0-475f-B680-6bd75fbd3d2a
-
Environment:
I have a workgroup Windows 8 pro PC with all updates from Windows update. The PC is connected via WiFi (home) to a router (the same thing happens if I am connected to the router directly via RJ45). It's my "private network (NAT). I have the Windows Firewall is enabled in its default configuration. I use "Windows Defender" as my protection\firewall of virus software. "When I go to: change options for sharing different network profiles" under advanced sharing options. I try to turn on file sharing and network discovery in the private profile. It shows that "the private sector is the current profile. The radio button lights. However, when I go to the file Explorer / network I got the message ' network discovery and file sharing are turned off. " The network computers and devices are not visible. Click here to change... " I click to change, however when I click to change it keeps returning and gives me the same message. I then go in ""network control and Internet\Network and sharing Center\Advanced sharing settings " and the option buttons in private profile for the network discovery and file sharing are turned off."
If I turn off the Windows Firewall. Everything works. I need to open a hole in the windows firewall for 2 applications was discovered and network file sharing. I opened rather not just blindly ports. However, if this is the only solution, what ports do I need open.
Hi all
I have exactly the same problem. (and I'm not the only one. - There are many!) The problem does not lie with the Windows Firewall. If I turn it off, discovery network and file sharing is turned on-tour he turn it back on and its all disabled subsequently and the rest of the way. I've been round and round the forums of the world looking for a solution but still find a definitive answer. Can certain software engineering in Microsoft Please arrive at the correct answer.
Thank you very much
PT.
-
Log InSight can work with Cisco Catalyst and Nexus devices?
Hi guys,.
someone at - it use Log Insight for catalyst devices and Nexus?
Yes, the Insight journal will work with all the unstructured data sent via the syslog Protocol. Support for devices Cisco remote log to a syslog destination shipping as newspaper Insight.
-
VMware and Nexus internal support for layer 2 priority vSwitch (802.1 p)?
Hello
Can someone provide a definitive answer on whether different types of vSwitch manage layer 2 priority internally (i.e. 802.1 p). In other words, these switches internally generate queues waiting seprate, based on the received priority tag 802,1 p, then manage each of these queues at the specified priority (highest priority first transmitted). Or what's a queue internal so efectively not a priority within the vSwitch, just from any external switch (physical) marking in the path.
Interested in the answer for each of: standard vSwitch, Distributed vSwitch, Nexus vSwitch. In vSphere 5 and above.
I asked similar questions before, and no real clear answer. Apologies if I've simply not spotted, but I searched the docs of VMware and Nexus and of course google pretty bad too.
Thanks for the answers or pointers,
PeterB
The Nexus 1000v using CB - WFQ
With Cisco Nexus 1000V Series Switches Release 4.2 (1) SV1 (4) or more recent, virtualization environments can now also enjoy based on a class of weighted Fair Queuing for congestion management.
Here is a white paper.
http://www.Cisco.com/en/us/prod/collateral/switches/ps9441/ps9902/white_paper_c11-704041.html
-
Connectivity HP C7000 and Nexus 5000
We spend our ESX servers in a rack mount environment at C7000 enclosures with blades. Can someone talk about compatibility box blade HP and Nexus 5000? The little that I find seems to suggest that this match may not be 100% ready for primetime.
I have a HP Virtual Connect modules or exactly what FCoE lokks like with HP blades. Does anyone have more information on this specific vegetables or aware of this configuration, used successfully?
There is full compatibility between the HP 7000 and the Cisco Nexus 5000.
What you need to make sure if it is that you are up-to-date with all HP firmware and drivers Nic ESX.
Take a look on my blog that goes into this in detail:
http://www.wooditwork.com/2010/08/09/Flex-10-ESX-pre-requisites/
http://www.wooditwork.com/2011/02/17/Flex-10-ESX-design-with-simplicity-and-scalability-part-1/
http://www.wooditwork.com/2011/02/17/Flex-10-ESX-design-with-simplicity-and-scalability-part-2/
http://www.wooditwork.com/2011/02/18/scripting-Flex-10-ESX-design-with-PowerCLI/
http://www.wooditwork.com/2010/10/19/HP-Virtual-connect-for-the-Cisco-network-administrator/
-
The Nexus 5548 software update
Hi guys
I need to make a software on some switches of 5548 Nexus of 5.1 (3) N2(1a) version to version 6.0 (2) N1 (1).
I did the updates on cisco catalyst switches but never on the Nexus. How hard is it, and what process can abide.
Any help will be much appreciated
Thank you
First, you must consider the 6.0 release notes (2) and make sure you have no significant impact on the network. The upgrade on a Nexus is pretty simple depending on your configuration. Do you have the FEX switches connected to your N5548? I assume that you have the system, already downloaded kickstart files and a backup configuration was taken.
The following is an option, I used to upgrade the N5548 and also run some basic cleaning steps after the upgrade is complete.
switch # copy tftp://192.168.x.x/n5000-uk9-kickstart.6.0.2.N1.1.bin bootflash:n5000 - uk9 - kickstart.6.0.2.N1.1.bin
switch # copy tftp://192.168.x.x/n5000-uk9.6.0.2.N1.1.bin bootflash:n5000 - uk9.6.0.2.N1.1.bin
switch # dir bootflash: / / / [see uploaded to bootflash files]
switch # install all kickstart bootflash:///n5000-uk9-kickstart.6.0.2.N1.1.bin system bootflash:///n5000-uk9.6.0.2.N1.1.bin
You will be asked to confirm the upgrade, the switch will be also preform prechecks and advise whether the MU will be disruptive or without interruption.
switch # delete bootflash:///n5000-uk9-kickstart.5.1.3.n2.1a.bin [delete old files] after upgrade complete
Jay
-
Bike 360 and Nexus 4 not matching
I just bought the bike 360 and expected type of plug-and-play with my Nexus 4 but no way behavior. When they try to pair, Moto 360 disconnects immediately. SmartWatch reset several times but nothing.
Any idea?
Thank you!
Updated the porter Android app and it worked.
Thank you very much!!!
-
We sccm 2007 R2.
We used AD discovery to discover all the computer in AD and automatic installation. We are able to deploy the agent to computers.
I was on leave we I come back, I discovered that there us no computer system. An abducted person discovery method. I managed to re-create AD discovery of computers, but now all the computer shows that there is no agent installed.
Hi lefogwane,
Thanks for posting your question in the Microsoft answers Forum. For any questions about SCCM, please visit the following link:
http://social.technet.Microsoft.com/forums/en-us/configmgrgeneral/threads
Maybe you are looking for
-
I got an e-mail allegedly Windows this morning - when I tried to open it nothing happened. Now the games that I had in the starting box disappeared. I want to try to restore files in the backup and Restore Center. The brochure that I said to go to th
-
How will I know if a person can get into my computer?
-
I have everything, if records of installation/uninstallation and newspapers since I installed XP. I'm sure that the last set of Windows updates work. Is there a problem with the removal of old files/flies and connects using CCleaner? If not all, can
-
Windows explore appcrash wmvdecod.dll
Windows explore appcrash wmvdecod.dll - cannot do anything, the pop up screen says explore ceased. If I try to X out or to seek a solution, it closes and comes right off. An endless loop. Impossible to get in Start button or all files - mouse w
-
Number shaped with two digits "behind the point" :-)
Hello Please excuse my very bad English because I'm french :-) I use the beta JDE v4.7 and the Blackberry Storm Simulator included. I would like to know how to format a calculated result as #. # (a floating-point value with two digits "behind the poi