open ports to prevent blocking of communicate with the firewall network

Similar Questions

• DEFAULT PROGRAMS THAT NEED TO COMMUNICATE WITH THE FIREWALL

  In the settings of firewall on windows7, what programs need to communicate through windows firewall for basic computer use

  In addition, in windows 7, which should be lit. Also for basic computer use

  Well, you could look on the Black Viper site for suggestions...

  http://www.blackviper.com/2009/10/01/black-vipers-Windows-7-Super-tweaks/

  http://www.blackviper.com/service-configurations/black-vipers-Windows-7-Service-Pack-1-service-configurations/

  Personally, I've never found that he needed to change the default values on all computers that I have and I certainly would NOT turn off UAC somehow...

• Error "" unable to communicate with your printer - this may be due to a firewall - check port TCP/UDP 139 is unlocked - reconfigure the firewall.

  "Unable to communicate with your printer - this may be due to a firewall - check port TCP/UDP 139 is unlocked - reconfigure the firewall.

  Original title: how to install the printing software to solve the error message?

  Hello

  Follow the troubleshooting steps in the following article and make sure that port 139 is unlocked:

  Windows Firewall may block some programs to communicate on the Internet after you install Windows XP Service Pack 2

  See also:

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  Note: Information provided in the article applies to Windows XP with Service Pack 3 (SP3) installed.

  If you use a third party firewall, I recommend you contact the software vendor for assistance.

• Can't seem to get the printer to the appropriate port to communicate with the printer Lexmark 2480.

  WndOws XP install problems with Lexmark X 2480 printer no cd

  Can't seem to get the printer to the appropriate port to communicate with the printer Lexmark 2480.  Downloaded, but prints blank pages.

  Hello, ColoChick,

  Your question must be posted in the hardware and drivers Forum.  Note the drop-down menus...

  http://answers.Microsoft.com/en-us/Windows/Forum/performance

  Search for drivers for your Lexmark printer.  The complete set is recommended for a full installation.

  http://support.Lexmark.com/index?http://support.Lexmark.com/index?locale=en&page=product&UserLocale=en_US&ProductCode=LEXMARK_X2480&focusedTab=downloads#2

  You can also try the universal print driver

  http://www1.Lexmark.com/en_US/software/UPD/index.shtml

  If possible, contact Lexmark for the installer of physical media (CD)

  Q: How can I contact the Lexmark parts?

  R: customer support is available Monday - Friday from 09:00 - 18:30 AND

  E-mail: * address email is removed from the privacy *
  Phone: 1-877-577-2787
  Fax: 1-800-258-4880

• How to block a DOS attack while allowing clients to communicate with the server

  I need a temporary solution for a dos attack. I am running Windows 7 Professional and need to block a DOS attack while allowing customers to communicate with the server

  Hi Vinniethetouch,

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited to the

  TechNet forums; We recommend that you post your question in the TechNet Forums to get help:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• Event gateway to communicate with the ports series

  I'm not so familiar with event gateways so sorry if I ask a question wrong. Can we use event gateways to communicate with the serial ports? Thank you.

  Can we use event gateways to communicate with the serial ports?
  N ° at least, not directly. Serial ports are physical, material, while ports dealing with event gateways are virtual, software.

  The event gateway is simply the code that listens to events in a Coldfusion application. He then responds accordingly. For example, the event Socket gateway is the code that listens on a TCP - IP port, then sends or receives messages via TCP - IP protocol.

• SERIOUS HELP NEEDED: How to prevent an application to communicate with the internet?

  Hey guys, I use an application called VLCStreamer on my iPad and I just want to know how I can help but communicate with the internet. For example, I don't want VLCStreamer to be contacting the author of the application.

  Thanks for any help!

  Put your iPad in airplane mode.

• Printers HP B110a cannot communicate with the laptop, but both will be connected to the router?

  OK, here's an interesting problem that has been banging my brain for hours, one of my friends has a HP Photosmart all in one printer B110a. Now I can get the printer to connect to the wireless router, no problem. Can I also have the phone to connect to the router, the problem is that the printer cannot communicate with the laptop. The router brand and model is the Linksys wrt54g

  Now, I took my friends laptop home and tried to see if she could detect my wireless printer model different on my router which is a TP WR340GD I went in devices and printers, and went to Add a printer and Add Printer wireless, it instantly detected my printer via the wireless network. There is no problem on the side of the laptop. I am sure that any firewall on the laptop was turned off when I tried the connected printer.

  So now I have my friends printer here with me and decided to try and see if I could detect the HP Photosmart printer All In One Printer on my laptop on my TP WR340GDwireless router. Yet once, it worked perfectly and it has detected the printer and works wireless without fault.

  I'm down now to the conclusion that the problem is with my friends router Linksys wrt54g I'm gone in the settings of the router, change the wireless channels, changed security between WEP and WPA/WPA2 and AES AND TKIP wireless and this does not solve the problem.

  I can access to the Photosmart B110a: the Web server integrated in a browser ONLY if I have the laptop to the router physically connected by Ethernet cable when trying to access my router from a friend, but I can access through wireless on my router. The problem is probably something very simple that I forgot, but I was more all I can think that I tried to reset harder than the printer cleaned the network settings on the printer as well from the display of the printer menu.

  I'm really lost now, someone at - it suggestions?

  Hey pcwizard, ok, I checked the router settings and Mac filtering turned on, so I decided to reset the router, it restored to factory settings. Re-Setup wireless and once again I tried, still had no luck with the laptop to communicate with the printer.

  in any case, I decided to connect the cable from the printer to the laptop and took the USB to wireless Assistant. As I reinstalled it the printer using the wired method.

  He told me that the rules of traffic incoming and outgoing firewall stopped communication between devices and assign port numbers 427-9000 etc.. However, I had turned off all firewall, Windows and Norton 360, which since then, I've replaced with a better anti-virus software.

  I went into the settings of the router, port forwarded the application numbers, tried again and is again no luck. I'm usually pretty good with computers, but it was really annoying me. So I went and had a coffee and a brainwave came and I decided to see if my laptop could detect and connect the printer to the router. As soon as I tried it, he finds and the printer has detected immediately.

  Then I thought there must be something on my laptop to friends who may be at the origin of the problem, when I looked, I noticed that my friend had the old software Vodafone Mobile Broadband running in the background which was connected to the router.

  So I closed and turn it off and tried again adding printer. SUCCESS now detects it and the printer is now communicate and respond with the laptop. I'm guessing that the Vodafone Mobile Broadband have a built-in firewall blocking the communication. However it is strange because it worked without problem on my printer at home, so I wonder if some how blacklisted broadband Vodafone IP address of the printer at a time on their router.

  I'm so happy, it's finally done, a lot of hours and work, and after all this time it was * beep * Vodafone.

  in any case Pcwizard I thank very much for trying to help, no doubt has given me a few ideas.

  Thanks again!

• Cannot add host ESXi 5.5 to vCenter for a routed network - cannot communicate with the specified host

  I was wondering if anyone has come across this problem before, who could give advice how to fix them:

  Host of pre-production UCS ESXi migration of a Production vCenter on another network (routing in place)

  Can ping both directions successfully - from vCenter Prod to the host of the pre-production

  no firewall between the two.

  902 port is open on the host

  Host connects to the pre-production vCenter on the subnet even fine

  VCenter production can add different hosts on the same network end

  Even with the various guests of ESXi UCS.

  ESXi host was completely disconnected and removed from vCenter inherited before attempting to add. No dvswitch physical or virtual.

  Then try and add, enter the user name and password and get cannot communicate with the specified host.

  Thank you

  The solution to this. Used ESX host 5.5 3B (3248547) update that disables SSLv3. (Ref: VMware ESXi 5.5 updated Notes version 3B) one of the consequences of this is that older versions of vCenter (such as trying to move the host) can not add/connect host.

  Enable SSLv3 to spend (port 443) on the resolved host (virtuallyPeculiar: connection A ESXi 5.5 U3b host to vCenter with a lower Version A.)

  Note: should not enable SSLv3 to Port 902.

  Ref:

  The SSLv3 Protocol on vSphere 5.x configuration (2139396) | VMware KB

  Many thanks to Suhas Savkoor of virtuallyPeculiar for resolution for this on his website display

• How do you communicate with the Apple Watch

  How do you communicate with the Apple Watch

  Hello!

  Welcome to the Apple community. I'm not quite sure what you mean when you say "communicate" with the Apple Watch, so I'll give you a few options that can respond to your request.

  (1) the Apple Watch supports Siri, just like the iPhone and the Mac. To apply, simply say "Hey Siri" while the wrist is triggered, and your watch will respond. Alternatively, you can hold the digital Crown and Siri will be activated. As soon as Siri is activated, you can ask him questions such as "what is the weather today" or "reminder", or "Let's start a workout."

  (2) you can manually send SMS via your Apple Watch by use of Siri, or opening the messaging app. That Siri send your messages, just say 'Hey Siri, send a text < name >' and Siri will open the Messages app and wait to talk to you about your message. If you want to move the Messages app manually, press the digital Crown and will take you to the home screen. In the home screen, select the Messages app (a green icon with a word inside bubble). Any existing message log must appear, and you can type on a given message log and choose to respond.

  (3) If you want to place a phone call using your Apple Watch, you can say "Hey Siri, call < contact name >". If you have several numbers for a particular contact, Siri will ask you what number you want to call. You can also you can present a more specific request like 'Hey Siri, call < contact name >, < number >' with the number favorite is 'work' or 'House' or 'mobile' etc. So the demand go something like "Hey Siri, call Barbra, House".

  If you are still at a loss, with regard to the types of orders that Siri will accept, you can always ask. Say 'Hey Siri, what can you do?' and she will give you a list of commands that she will answer to the.

  If all goes well, I addressed your question. If not, please provide a little more information and I'll do what I can to help you.

  Good luck!

• Error: "unable to communicate with the TWAIN device" with brother MFC7820N

  Original title: can I connect a scanner through a switch?

  I'm trying to analyze something like I did it many times with my brother MFC7820N hung on my tablet. But recently, I replaced a 2nd router I had in my system that failed with a new Dynex switch.

  I have my internet modem and 2 computers connected to a Linksys wireless router. I have another ethernet cable connecting the router to a new switch. I have my 2 printers attached to the switch. One is a Brother HL-2700CN color laser and the other is a brother MFC7820N mutli-function. It use PaperPort to scan stuff on him, since provided on the CD with the device.

  So today I open PaperPort and click the Scan button and it appeared an error saying unable to communicate with the TWAIN device box.

  So I clicked on a doc shown in PaperPort that I had scanned a few weeks ago and I click right and select Print and printed to this MFC7820N.

  Then I come back to click on scanner again and yet again, it appears that box. So I watch and WIA-Brother MFC-7820N LAN is displayed in the Scanner marked drop-down list box. So I switched the power of the MFC and tried again and it still appeared that same box again.

  OUCH! I'm going nuts! You have any ideas?

  Hi Jeff has Davis,
   
  Method 1: Uninstall and reinstall the driver again and check if it helps fix the problem.
   
  See this article for more information:
  How to manage devices in Windows XP
   
  Method 2: Try the suggestion given in this article:
  'Could not enable TWAIN Source' or 'He has not find scanner' Error Messages are displayed

• Error message when printing - Communication not available, cannot communicate with the computer

  Original title: for some reason, my computer and printer communicate is no longer... I spent every day toubleshooting... always get this box: Communication not available, cannot communicate with the computer

  I have a Dell Inspiron E1505 laptop and Dell AIO 924 printer if that helps! all cables are correctly connected, unplugged, replugged, shut down rebooted, uninstalled / printer driver, always even reinstalled!

  uuggghhhhh!

  flustered2,

  You recently reinstall the operating system? If so, have you installed the drivers in the order?
  How to download and install drivers in the correct order

  First run delete print jobs to remove all print jobs stuck in the queue.

  Unplug the printer.

  Download and run the patch (cleaning printer utility) until it prompts you to restart your computer.

  Restart your computer.

  Now you can install the printer using the Dell Printer 924 disc.

  Link to the patch/drivers(if needed) is to...

  Dell 924 Photo-All - In - One Printer owners thread (W7)

  Don't forget the programs anti-virus and firewall will block communications.

  Also try this tweak...

  Go into Device Manager (right click on my computer, left click Properties, material of the left click, left click Device Manager)

  Go to the section USB controller, and then click the plus sign +.

  Go to each USB hub root and right-click on it, on the left, click Properties, on the left, click power management. Uncheck the allow the computer to turn off this device to save power.

  Restart your computer.

  Rick

• My Lexmark printer stopped working and the error message says "printer cannot communicate with the computer" (from "twisted into the USB pins?).

  When my printer stopped working because of error messages about "printer cannot communicate with the computer" (from "twisted into the USB pins?), I tried to change to 2nd USB port without success. I tried a new cable; that did not help.

  Then I uninstalled and reinstalled my Lexmark printer and changed the error message. Now, the printer does not work because "the USB device is not recognized."

  I tried to update the chips; Use 1 USB port; and using the old cable, all this without success. I checked the connections of the cable to the printer and the PC and turn on the printer and goes off; I'm out of ideas. Any other suggestions?

  Hi ChristineKrause,
   

  Here are some links that might help you:

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  Advanced troubleshooting tips for General USB for Windows XP problems

  Try the steps listed in the items mentioned above and see if that helps you solve the problem.

• The Dell printer cannot communicate with the Dell computer.

  It seems that suddenly my Dell AIO 942 printer cannot communicate with my Dell Studio 17computer.  These devices have been the transparent connection until two days ago.  I've set up a restore point, I installed the drivers, unplugged and re plugged 110 s and USBs, used different ports and I still have the same, printer cannot communicate with the State of the computer.   Copy and scan functions are good, Windows Vista operating systems.  How can I find these devices to their previous state of communication?

  Jesse,

  Thank you very much for the detailed information. It really give us a head start trying to solve the problem.

  Please answer these questions to get more clarity-

  (1) what are the other steps in troubleshooting tried by you so far?

  (2) other changes on the computer that I should know about?

  In the meantime, I have you refer to items offered on the Dell website - troubleshooting

  http://www.Dell.com/support/home/us/en/19/product-support/product/Dell-942/research

  You can also have a look at the Microsoft article as well-

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Get back to us with the results.

• The printer (Lexmark x 5470) cannot communicate with the computer (Windows Vista Home Premlum)

  The printer (Lexmark x 5470) cannot communicate with the computer (Windows Vista Home Premlum).  I tried these solutions below, but it still does not:

  1. ensure that the printer is powered.

  2 disconnected then reconnected the power cable from the printer.

  3 unplugged then replugged the USB cable.

  4 checked Windows Firewall setting to ensure the communication of the printer is not block.

  5. restarted my computer.

  Please help me solve this problem.

  Thank you!!!

  Have you just tried reinstallling your printer yet? Even if it was working before, file corruption or other problems can sometimes be cured by doing this?