Operational status - WLC 2504 AND LAP 3501
The AP is connected to the WLC but guard take down is Raodio. As suggested, I played with the settings of PoE, nothing helps...
Sea 1 18:30:36 Feb 2012 |
AP Interface: 0(802.11b) State Down operation: basic Radio MAC: e8:ba:70:93:81:60 Cause = reset interface radio status: NA | |
3 | Sea 1 18:30:36 Feb 2012 | AP Interface: 0(802.11b) operation State Up: basic Radio MAC: e8:ba:70:93:81:60 Cause = Admin on Radio status change: Enable |
4 | Sea 1 18:30:36 Feb 2012 | AP Interface: 0(802.11b) State Down operation: basic Radio MAC: e8:ba:70:93:81:60 Cause = Admin on Radio status change: disable |
5 | Sea 1 18:25:32 Feb 2012 | AP Interface: 0(802.11b) State Down operation: basic Radio MAC: e8:ba:70:93:81:60 Cause = reset interface radio status: NA |
6 | Sea 1 18:25:29 Feb 2012 | AP Interface: 0(802.11b) operation State Up: basic Radio MAC: e8:ba:70:93:81:60 Cause = Radio reset due to the Init. Status: NA |
Any ideas... I've checked everything... AP is Port 4 of the WLC
*Mar 1 00:00:12.988: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process= "Init", ipl= 0, pid= 3
Now, that's what I was looking for!
Your 802. 11 b radio is dead. Please contact Cisco to get this replaced WAP.
Tags: Cisco Wireless
Similar Questions
-
2504 and 3802i new installation does not
Hello
I installed a new WLC 2504 and new APs 3802i, however the APs are not fully functional. They keep cycling the RED/GREEN/BLUE LED, which I don't see in the troubleshooting guide. WLC running 8.3.102.0, APs connect, take a license, but none of the radios come and he can't even see 2.4 Ghz I installed 5508 s front and WiSMs and did not have this problem with 1252/1142/2602 APs. Don't know what the hell miss me, and hoping that the group can help out me. TAC was told that they do not receive enough power that is a scripted response. Watch controller PoE as PoE/power. I had to install a device on the controllers pack? I went from 8.1.115.0 (plant) right to 8.3.102.0 because the 115 does not support the 3802 s.
Summary of access pointsTotal Upward Down 802.11A/n/AC radio In detail 802.11b/g/n Radios In detail Dual-Band radio In detail All APs In detail 3800 require PoE + (802.3at) to operate. Because you got a line card PoE will not work correctly. See below for the required power for 3800 series.
Not sure what you want for a console output, so I posted AP run-config and show log:
If you have a complete when console output AP trying to register, we can see exactly the problem at hand. Even with the limited log messages you can see is the negotiation of PoE has failed. If you have any PoE switch + you can confirm a 3802 works without any problem. In this way, you can confirm the problem with PoE HTH Rasika * Pls note all useful responses *. -
Cisco WLC 2504 internal DHCP does not work properly
Hi all
I m trials with a Cisco WLC 2504 and some APs of 1832. I set up a DHCP scope on the interface of the controller with 2
a large number of different configurations, but the DHCP protocol does not work and Don t Access Point to obtain an IP address. My first question: is it possible to do DHCP for Access Points or only for wireless clients?
These are my interfaces:
Interface of the PA-Manager:
My DHCP scope:
Advanced DHCP:
I forgot something? Is there anyone using DHCP for its access points?
Thank you!
Hello
On Cisco WLC internal DHCP, you can add the option 43 to say where APs must register. In this case, they will try to resolve the DNS CISCO-CAPWAP-CONTROLLER or CISCO-LWAPP entry.
Let me explain briefly how AP-Manager works on WLC:
- Boots of Access Point and sends a discovery request to the management interface of the controller using the intellectual property you configured as DHCP Option 43 (as described above, it can be resolved by the DNS entry)
- Controller, sends it a response discovered that contains the name of the system, addresses AP-Manager, the number of access points already connected to each interface AP-Manager and the overall capacity of the controller.
- Joints access point controller using the less loaded interface AP Manager.
With this, every AP Manager must have a good configured interface and be connected to a different port, no LAG.
I drop a post here sometimes there is which might help:
https://supportforums.Cisco.com/document/118311/configuring-multiple-AP-...
Thank you
PS: Please do not forget to rate and score as correct answer if this answered your question
-
Hello.
We are going to upgrade a WLC: AIR-CT2504-15-K9 for free: 8.0.120
This is a new installation and we will install 15 TOUR of this model: AIR-CAP2702E-A-K9.
We went through the compatibility matrix and release WLC 8.0.120 correspond to LAP: 15.3 (3) JA4.
the upgrade mention WLC process which, after the upgrade of the WLC, completed the upgrade of the TOUR begins automatically, so I have a few question:
- I need to plug all the way AROUND (15 LAP´s) to the cable network so they can be automatically upgraded?
- This release is selected automatically during the TOUR?
- Y at - it a GUI WLC option where I indicate where the exit for LAP (15.3 (3) JA4?)
- I tried to download version 8.0.120 for 2504 WLC but need a Partnert Lincense. Would you mind giving a link where I can download this version?
- We assume that, above all, he must perform a communication between the WLC with TOWER (15) using the current version, is this true?
- If the 2504 WLC and LAP 2702 have different (different version of matrix compatilibilty) is it possible to upgrade the version of the TOUR? can they communicate with each other so we can proceed with the upgrade?
Thank you in advance your response earlier.
Attn.
Roger Majo
Hi Roger,
Please find below the details of my side which will be useful for you.
I need to plug all the way AROUND (15 LAP´s) to the cable network so they can be automatically upgraded? Yes... Or whenever you connect to the network access point it will automatically connect to WLC through DHCP option
This release is selected automatically during the TOUR? Controller of which is running
Y at - it a GUI WLC option where I indicate where the exit for LAP (15.3 (3) JA4? > Show ap image all the )
I tried to download version 8.0.120 for 2504 WLC but need a Partnert Lincense. Would you mind giving a link where I can download this version? Contact account executive-paper license (check you have valid Support Cisco)
We assume that, above all, need a communication between the WLC with TOWER (15) using the current version, is - that true? No need... AP will automatically for the last reason that is available in the controller
If the 2504 WLC and LAP 2702 have different (different version of matrix compatilibilty) is it possible to upgrade the version of the TOUR? Can they communicate with each other so we can proceed with the upgrade? Explained earlier
Thank you
Sam
-
Can I have Windows 7 Professional and Windows 10 operating systems on the same lap top
Can I have Windows 7 Professional and Windows 10 operating systems on the same lap top
Yes, you can, but not with the free upgrade, you will need to purchase a full license for Windows 10 to do this.
Step 1: purchase a license:
Buy Windows 10 family/professional edition
Step 2: Download Windows 10 and create a bootable copy
How to download official Windows 10 ISO files
Step 3: Create the partition then install dual-boot configuration:
How to: install a Setup to dual-boot with Windows 10 and earlier versions of Windows
-
difference between the operational status of APs to the TOP and REG (registered)
Hello guys,.
I want to know what is the difference between the operational status of APs to the TOP and REG?
Thanks in advance
A radio operating state is up/down. REG AP means that the PA has joined with success the controller. The AP must be in the State REG (registry) radios appear.
-Scott
Please evaluate the useful messages *.
-
Someone in the community all managed to connect a controller wireless lan to a 300 SG? I know that the WLC 2504 needs to be connected to a switch L3, but also a gigabit ethernet port. I plan on upgrading the firmware of the SG300 to version 1.3.5.58. Since the 1st version seems to have some problems using L3 switching.
Thank you
-Bill
The biggest drawback for most people is the VLAN tagging. The switch in many ways is like a switch in IOS, but it is not simply a switch of IOS.
Just keep in mind that if you make a layer 3 VLAN (assigned IP address to the VLAN), if sure the default VLAN has first of all a static IP address then go to make interfaces VLAN additional.
config t
int vlan 1
IP address 192.168.1.254/24 or anything else you want.
Continue to add the IP address and VLAN
config t
database of VLAN
VLAN 100
int vlan 100
IP address x.x.x.x /xx
Then you can make the trunks, etc. for VLAN desired.
config t
int gi0/1
switchport trunk allowed vlan add 100<- this="" will="" make="" the="" port="" vlan="" 1="" untagged,="" vlan="" 100="">->
Most people transitioning to this switch get caught up on these 2 things for some reason most any.
If you need help to set up the switch, you can always call the HWC, they have 24 hour support (without contract) or you can always feel free to hit me up (free support too)
-Tom
Please mark replied messages useful -
WLC primary and secondary - Config DHCP Scope
Hi all
WLCs: AIR-CT2504-K9
We have therefore two 2504 s each in separate locations. Inside of each of the Access Points, we have configured one of the controllers of the WLC primary and the other as the secondary WLC tab HA. So my question has to do with the internal DHCP configured in each of the controllers scope.
We only use the internal DHCP server of the WLCs for our Public Wi - Fi network. And I was wondering if I should configure the DHCP scope even in two controllers, or if they are supposed to be different?
For example:
Elementary WLC - extended DHCP: 10.12.202.110 - 10.12.202.200
Secondary WLC - extended DHCP: 10.12.202.xxx - 10.12.202.xxx?The way in which access points are configured, they should only be attached to a controller or another. So that the way its set up it shouldn't be some APs on a single controller and some of the other. They should all be attached to the WLC even at any time. So, given that I can configure the same scope on both controllers?
Any ideas or suggestions would be greatly appreciated!
Thanks in advance,
MattYes, you can set up this way, as long as you don't expect not so much operational WLC & customer service at the same time.
If you think to expand this network of comments, I suggest you stay away from using DHCP internal like these WLCs has ever made to use as complete apart from entire DHCP servers in large scale networks.
HTH
Rasika
Pls note all useful responses *.
-
WLC 2504 cannot access the GUI...
Hi all
I'm not sure what I did wrong, the 2504 itself has only 4 ports and no port management but I heard it's actually port 1 (even if there are no labels for this). That's what I've done so far to try to access the GUI:
in CLI mode, I have
(1) put AP managament address like 10.151.55.129 255.255.255.224.
(2) I have activated the adminmode on port 1, which I assume is management port and enabling admin mode is the same as "no shut" on switches I guess; Here is the command I entered:
(Cisco Controller) config > adminmode port 1 turn on
(3) enabled HTTPS/HTTP through commands:
(Cisco Controller) config > activate network secureweb
(Cisco Controller) config > activate network web-auth secureweb
(Cisco Controller) config > network webmode enable
(4) I then reset system and verify that the changes took place to help display the synthesis network, as shown below. I also activated mgmt via dynamic interface to see if it makes a difference:
RF-network name... TEST_WIFI
Web Mode.................................... Enable
Secure Web view... Enable
Secure Web Mode Cipher-Option high... Disable
Secure Web SSLv2 Cipher-Option Mode... Disable
Secure Web Mode RC4 Cipher preference... Disable
OCSP........................................ People with disabilities
Responder OCSP URL...
Secure Shell (ssh)... Enable
Telnet...................................... Disable
Transfer Ethernet multicast... Disable
Transfer of broadcast Ethernet... Disable
Multicast/Broadcast AP mode... Address multicast: 225.225.225.225
IGMP snooping... People with disabilities
IGMP timeout... 60 seconds
Interval between IGMP queries... 20 seconds
MLD snooping... People with disabilities
MLD timeout... 60 seconds
Interval between MLD queries... 20 seconds
Period of inactivity of the user... 300 seconds
ARP timeout... 300 seconds
Cisco AP by default Master... Disable
Join AP priority... Disable
Mgmt interface wireless... Disable
Mgmt Via dynamic Interface... Enable
Filter MAC bridge Config... Enable
Safety of bridge mode... EAP
Mesh full sector DFS... Enable
Relief of AP... Enable
Support CMCC Auth Web... People with disabilities
Web Auth redirect Ports... 80.1
Web Proxy Auth Redirect... Disable
Bypass-Web Auth Captive... Disable
Web secure Web Auth... Enable
Quick change SSID... People with disabilities
Discovery of the AP - IP NAT only... Activated
IP/MAC Addr binding Check... Activated
Status of CCX-lite... Disable
oeap-600-WLAN-dual... Disable
oeap-600 local-network... Enable
mDNS snooping... People with disabilities
mDNS interval between requests. 15 minutes
(5) I installed my PORTABLE NIC to be 10.151.55.20 255.255.255.224 and connected to port 1 on wlc 2504; but I can't ping 10.151.55.29 nor do I navigate to https://10.151.55.29/. The port appears upwards (the flashing green lights on port 1 and Portable NIC also Flash).
Any help would be appreciated
If your connection to your laptop direct to port 1, then you have untagged the management vlan. Now you have configured for vlan 10, you must set to vlan 0.
You will then be able to ping to the management interface and connect to it through the user interface.
Sent by Cisco Support technique iPhone App
-
AP 1131ag 802. 11 a Oper status = down
I have a Cisco WLC 2106 and 1131ag Access Point. The 802. 11a / g Radio 'Operational status' = down. All the other radios that are on the RISE. I wonder if this is a normal behavior that none of the clients are connecting to it on the 802. 11a / g Radio. Can we confirm or provide assistance with the fix.
Thank you
On the homepage, click the "Détails" link under all items. Choose the AP make sure under status choose 'Activate' in the menu dropdown.
When you console in the AP, are you sure it is down/down and not zero/down reset?
-
Hello, I use a Compact Rio 9074 with an EtherCAT NI 9144 chassis extension
I am able to see both devices 9074 and 9144 Labview project, but when I try to deploy configuration 9074 controller tracking error is displayed:
I tried deployment while defining the Configuration Mode and Active Mode. Also, when I check on the status of master Ethercat online its State in: pre-operational with errors. And appers this message: error-2147137769 occurred at an unidentified place
I'm using Labview 2011 and the OR cRio has installed:
I tried formatting cRio and reinstall NI Ethercat and scanner again
I wonder if anyone has the same problem, I'd appreciate any help.
Thanks in advance
Thank you very much, DirkW worked for me immediately
-
New authentication active directory on wlc 2504
Hello
There is problem with very often a new authentication for servers active directory. Every time only if:
-loose client wlan/wifi because of the wifi hole or low RSSI
-output of build for a while customer
-wlan loose customer due to problem with homelessness (slow, not perfect)
There is possibility to keep authenticated users? I had hope that options: sleep customer, max session timeout, max idle timeout
help, but they do not work for me :(
My access point (2702) are all in a group flexconnect. WLC 2504 (8.1.102.0). My security in WLAN config is:
Layer2: wpa + wpa2, PSK
Layer 3: web policy, authentication with LDAP servers + asleep on client
I always try to improve the radio covers n fast roaming (11 k, r, v) but if someone leaves the area wifi, to do authenticated which is a little annoying...
Thanks for any advice or an index
Peter
You want people who re - attach to your network for to re-authenticate. It's a good thing. We do not want people using the old credentials, or expose you to a security breach.
This behavior is by design - and good.
-
Cisco WLC 2504 - Access Points do not reach the controller
Hello world
We bougth a Cisco WLC 2504 with two AIR-AP2702I-UXK9 Access Points. The problem is that the AP do not join the WLC.
The output from 'show join ap stats' shows the following:(Cisco Controller) > view join ap stats summary all the
Database Mac EthernetMac AP AP name IP address Status
00:35: 1a: B1:A9:60 00:f2:8 b: f4:1 has: 9 c AP00f2.8bf4.1a9c 192.168.10.23 joined not
00:35: 1a: C9:99:B0 00:f2:8 b: 77:b7:fc AP00f2.8b77.b7fc not joined 192.168.10.24(Cisco Controller) > show join ap 00:35:1 detailed stats to: b1:a9:60
Synchronization phase statistics
-For the synchronization request has received... Does not apply
-For the synchronization completed... Does not applyDiscovery phase statistics
-Applications received discovered... 114
-Answers success of discovery... 114
-Discovery failure processing... 0
-Purpose of the last unsuccessful attempt of discovery... Does not apply
-Attempt to finally successful discovery time... 20:15:40.106 16 June
-Discovery attempt ultimately unsuccessful time... Does not applyJoin the live statistics
-Join applications received... 57
-Join sent successful responses... 57
-Processing of the join request without success... 0
-Purpose of the last unsuccessful attempt to join... Does not apply
-Attempt to join finally managed time... 20:15:50.414 16 June
-Join finally failed time... Does not applyConfiguration phase statistics
-Configuration requests... 114
-Answers configuration successful... 0
-Processing configuration failed... 57
-Purpose of the last unsuccessful attempt to Setup... Invalid license in the application configuration
-Attempt to finally successful configuration time... Does not apply
-Time finally failed configuration attempt... 20:15:50.810 16 JuneLast the decryption of the AP details failure messages
-Last message decryption failure reason... Does not applyDetails of recent disconnection AP
-Last AP connection failure reason... Does not apply
-Last reason for disconnection AP... Unknown failure reasonLatest summary join error
-Type of error that occurred in the last... Application of configuration rejected LWAPP
-Reason for the error that took place the last... Invalid license in the application configuration
-Time which occurred the last error to join... 20:15:50.810 16 JuneDetails of sign-out AP
-Last AP connection failure reason... Does not apply
Ethernet Mac: c 00:f2:8 b: f4:1 has: 9 Ip address: 192.168.10.23Would be grateful for the help.
Best regards
MarcHi Marc,
Make sure first that your controller has software code 8.0.x or above, if first better it. Here's the code recommended by TAC
Then, try the UX above deployment guide to begin. Under Advanced tab WLAN, you need to enable "of the first universal ap' in order to use this app provisioning & connect to the AP.
If you have more than 1 AP, then you must start 1AP using this application. Other access points that you can feed them upward, while AP original is also powered, so they'll use protocal called NDP & start them automatically
Let us know how it goes
HTH
Rasika
Pls note all useful responses *.
-
Don't WLC 2504 media HA or not?
We have Cisco WLC 2504 (software version: 7.3.101.0) in our network and management access 10 points, we are now trying to build High Availability (HA) in the WLAN settings. So I need details that this existing platform is capable of supporting HA.
Required clarification as follows.
1 support WLC 2504 HA?
2. If the AP is supported if a license is required to enable it.
3. What is prerequisite software to enable it.
4 Setup guide to enable HAAttached: existing WLC BOMs
HA PA SSO:
http://www.Cisco.com/en/us/products/ps10315/products_tech_note09186a0080bd3504.shtml
HA N + 1
http://www.Cisco.com/en/us/docs/wireless/technology/hi_avail/N1_HA_Overview.html
AP high availability
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008064a294.shtml
Thank you
Scott
Help others by using the rating system and marking answers questions as 'response '.
-
a WLC 2504 does support mobility with WiSM1 on the 6500 Series group
If a WLC 2504 supports the mobility with WiSM1 on the 6500 Series group.
Model: WLC 2504
Software version: 7.3.101.0Model: WiSM1
Software version: 7.x.x.xYes and no.
Yes, mobility is supported.
No, because I don't personally recommend inter-controleur of roaming. It is true when you are dealing with 4400/WISN-1. This is even truer when you WLC running two (or more) different codes.
Maybe you are looking for
-
G4 virus begins but before full initialization says I must reboot and lock me up.
Mac G4 starts but before it fully starts a message appears and say "you must restart your computer", locking the machine up to what I held down the power button down to turn off the machine. I booted safe and it seems quite different that the screen
-
I can't access my icloud on my mac computer
I'm trying to access my icloud on my mac computer pro... How can I change my apple ID. Whenever I put in that changed the old pop on?
-
See the title of the question
-
Windows ultimate Vista Recently I bought windows vista Ultimate edition with additions of 32 and 64-bit. Can I use the 64-bit on my desk and the 32 bit on my laptop?
-
Impossible to uninstall the drivers of MCIR keyboard permanently
The following keyboard drivers seem to block several keys, including the colon and backslash in DirectX 10 and other applications:Microsoft eHome Remote control keyboardKeyboard MCIR Microsoft eHomeKeyboard 109 MCIR Microsoft eHomeHID keyboard device