OR GPIB-USB-HS + NI GPIB-USB-HS vs

Similar Questions

• Using NI USB-GPIB controller Zeiss C90 CMM control

  I have a Zeiss PCDMIS CMM running 32-bit on Windows XP with PCI GPIB (488.2 2.7.3)

  If the controller is 8 bits, but work with my 32-bit system already, can I export the config VISA file, change on a 64-bit of Windows 7 with a USB to GPIB computer, and import this file into a newer version of the driver 488.2?  (change of bits or a more recent version of 488.2 will be a problem?)

  Hi Ryan,

  As long as you save this export config file, you should be able to load it into the second computer MAX.  I can't find anything that says that there will be problems with the little change.  If you are really worried about it however, give it a try without getting rid of your original computer.

  It seems that you already know how to transfer the settings above, but here's a KB on how to do this http://digital.ni.com/public.nsf/allkb/BF528312C9A5423A862565BC00731EC0.

• Connection of an instrument with GPIB-USB connection.

  I am trying to use a GPIB-USB adapter to control a unit of Source of LabView. However, I have problems my instrument drivers to recognize the GPIB address specified for the device. I have attached an image below the address specified by IO Keysight connection Expert. I am currently trying to initialized the EMS with the GPIB driver I have attached below. Because of my knowledge limited in LabView instrument control, how should I approach of collecting the correct address of GPIB and recognize it in my VI?

  Hi wyattcurtis824,

  Before we dig into the LabVIEW code, I would recommend a Test Panel of max aperture and trying to communicate with. Are you able to send orders via Keysight connection Expert or NI MAX and see the valid data?

  In addition, when you run the vi in LabVIEW, is pilot it returns an error in the error on the box? If so, what the error is?

  This shoule information help us to the root of the problem.

  Best,

• GPIB-USB-HS shows no MAX after that I used the wizard NI VISA DRIVER

  I accessed GPIB USB HS in the MAX software. As I was not able to communicate NF RLC remotely, so I tried Wizard DRIVER VISA OR according to tutorial Assistant pilot NI VISA , however, thnings went wrong and I am not able to see same GPIB to the MAX software now. What should I do now?

  The first picture below shows the GPIB USB HS as shown in the software MAX and the other image shows no GPIB USB HS.

  

  

  Yet once I installed driver USB GPIB link below:

  http://www.NI.com/download/NI-488.2-15.0/5427/en/

  Its working fine now.

  Thank you.

• GPIB-USB-HS and USB-8451 communication issues - appearing only in VISA

  Hello

  I recently started a new job and have had communication problems between my adapter GPIB-USB-HS, my VISA or MAX-Labview and USB-8451 I2C/SPI interface.  I installed LabView to 32 bits, OR-488. 2, the driver for the 8451 on my windows desktop and VISA 16.0 7.

  In the windows Device Manager, the 8451 appears as a device USB of NI-VISA and Gbspecifications FOR-USB-HS presents itself as a GPIB Interface of NOR.  Two of these instruments are recognized NI Max so but communication Gbspecifications FOR add-in adapter (and connected instruments) fails and he can't find the instruments and the self-test fails with a hardware error unknown gpib (-37052).  The watch also neither device VISA Interactive Control.

  The ready light is lit on the GPIB-USB adapter and the 8451 flashes green as if nothing is wrong at the end.  I uninstalled all the software of NOR and reinstalled, and I run MAX as an administrator.  Is there possibly some computer settings I could neglect or need to change to open a communication?  Any other ideas on why I can't communicate with devices?

  Thank you!

  Trey

  This is a device-Lock software that my it was preinstalled on the computer blocks the USB port.  SHE has added features like confidence, and now it works.

• Data acquisition using the USB-GPIB 82357 B interface for 4395 impedance Analyzer has:

  Hi all

  I tried to communicate Analyzer 4395A impedance with interface USB GPIB 82357 B using the command of expert keysight and Labview module tutorial. I couldn't able to find orders of SCPI (Standard for programmable Instruments orders) for 4395 A impedance Analyzer in the expert keysight command. Please help me on the subject of what are the other possibilities to acquire data from the Analyzer of impedance 4395 A using the interface USB GPIB 82357 B.? Is it possible to get LABVIEW plug & play drivers for USB-GPIB 82357 B interface? Our main goal is to control the parameters of impedance measurement and draw F vs IZI and theta vs F as well as get parameters of equivalent circuit on a PC with LABVIEW GUI.

  Can't wait to help.

  Hello!

  I agree with 'heavy '. For more information on how to program a 3rd device contact the manufacturer because they have the knowledge. Unless there is already a LabVIEW driver for this device, you would have to implement that yourself and need information from the manufacturer.

  Regarding your question if the GPIB-USB is unsuitable, it is quite easy to answer: If you want to communicate with a peripheral GPIB NI GPIB-USB can do this. But you would probably need a driver to use the GPIB of meaningful communication bus.

  Best regards

  Christoph

• GPIB-USB-HS will recognize any instrument in LabVIEW but somewhat done in MAX - help

  Hello

  I'm having a problem getting my GPIB-USB-HS device to recognize instruments in LabVIEW.  The unit has been running year last on many instruments.  I tried the GPIB-USB-HS other materials too just to make sure it wasn't a defective unit.

  NOTE: I installed the latest drivers for NI-VISA 5.1.1 and 300 of NOR-488. 2 for Windows XP

  See the images below:

  It's the idsplay to the MAX:
  I'm not sure why there is a yellow "!" next to GPIB0::INTFC, I think it's an indication of my question.  However, note that the instruments connected to my GPIB-USB-HS are counted in MAX.  As you'll see LabVIEW 8.5 does not recognize them.

  

  I get this error Max warning when I try to open TOOLS > NI-VISA > VISA INTERACTIVE CONTROL:

  

  It comes to the image of my LabVIEW 8.5 window when I try to select a VISA of an instrument (including MAX recognizes):

  

  Any help would be much appreciated

  Thank you

  -Brian

  Thank you all for your help,

  Problem solved after hours of uninstallation and reinstallation of all devices/software from National Instruments.

  Once all programs have been uninstalled (with a disk cleanup on my unnecessary hard-maybe records)

  LabVIEW 8.5.1 has been reinstalled

  NOR-DAQ has been reinstalled

  NI-Visa 5.1.1 has been reinstalled

  NOR-488. 2 worm 2.7.3 has been re-installed (correctly)

  Now, LabVIEW recognizes all ports/devices and connects to the instruments properly once more.

  My question must have been installing LabVIEW 8.5.1 after already installing LabVIEW 2009.

  Somewhere during the installation of 8.5.1 - main post problem occurred.

  Thanks again

• Device ENET connect computer USB using NI GPIB-ENET/1000

  Hello

  Currently, I am trying to connect to a controller PI E-712 has an ENET port on a windows 7.

  I have a converter NI GPIB-ENET/1000 and a GPIB-USB-HS cable and want to use the ENET end for the controller and the GPIB for contact with the computer, but is it possible? Or does only for GPIB-devices of connection for calculating rusing ENET?

  I have the drivers on my computer, namely the NEITHER-488. 2, IMAX can detect the GPIB connection and the cable has a light orange on the loan. Lights green ENET-converter for power, ready and the positions of the Act/LINK but nothing either of the GPIB for speak and listen to the lamps. When trying to connect, the computer does not see the device at all.

  Any help will be greatly appreciated.

  FrellZilla wrote:

  Thank you for your adivce.

  I am sure that tha the device does support ethernet. The problem is, however, that we cannot connect the ethernet to the computer itself. We do not actually use Labview but a program called DMACS, that's why we want to use GPIB on the end of the computer.

  The NI GPIB-ENET/1000 will not work for you. It is an Ethernet to GPIB device. Your instrument is not a GPIB interface.

  I'm not familiar with DMACS.

• GPIB to USB cable

  Hello

  I was wondering if GPIB NOR to ACR USB cable be used to control the instruments of Agilent. I tried 3 different instruments of Agilent and it doesn't work. The cable works for all the other instruments that we have.

  Thanks for your help

  The GPIB-USB controller can be used with any instrument that is consistent 488.1 and 488.2.

  You need to explain "it doesn't work" with details such as the model of the instrument, the error codes, etc.

• Place HP 34401 in Local with GPIB-USB-HS Mode

  Hello

  I'm using LabVIEW 2010 SP1 to control the 34401 HP with the NI GPIB-USB-HS device. I use I/O built-in 34401 instrument drivers.

  If I plugged in everything, the 34401 will be immediately placed in "Remote" mode when I run my software. However, I would like to be able to use LabVIEW to force the 34401 to 'Local' mode Unfortunately I could not find a way to do this. I tried Close.vi, but has no effect.

  Here are my planned operation if it makes things clearer:

  1. Launch the software
  
  
  2. Initialize the 34401
  
  
  3. Place the 34401 in the 4W resistance measurement mode
  
  
  4. Pass the 34401 in "local" mode so that the end user can adjust a knob until the desired resistance is obtained while seeing the value of the resistance to change on the 34401
  
  
  5. Re-initialize the 34401 when I need to switch to another measure

  If not, is there a way to get the 34401 to permanently display how it is taken in remote mode?

  Best regards

  Ian Williams
  Linear Applications Engineer
  Product precision linear, and remote sensing

  The feature I mentioned does exactly the same thing except that you have to do this awkward analysis of the address. It's a VISA function you have just used the search button to find (and have lit context-sensitive help) to obtain explanations of what he does.

• GPIB-USB-HS works selectively

   

  Situation

  -an old HP3962A works very well using a PCI-GPIB connector on a PC. Code of Labiew.

  -a digital Voltmeter K2000 works well using a hub of GPIB-USB-HS, on a laptop. Laview code.

  Problem:

  NIMAX does not recognize the HP3962 when you use the GPIB-USB-HS hub, on the laptop, although it recognizes seveal other instrument, such as the K2000 dvm.

  Thanks for the suggestions, Philippe

  After having removed the long 1.5 m GPIB cable and linking the GPIB-USB-HS unit directly to the old HP3562A unit, NIMAX recognizes this instrument (low level).

  Direct com on NIMAX does not, but the LabView code (old) written to read the data works.

  The bus speed was maybe the question.

  Resolved for now, thanks to you all.

• Difference between NI GPIB-USB-HS + and NI GPIB-USB-HS

  I would like to know the difference between GPIB USB HS + and HS (without the +)
  Seems to me that the HS has not onboard GPIB analyzer but with a GPIB ASIC chip.

  Main difference is speed, which is strange, the HS has a speed faster than the HS +.

  Any person using or has used before these two? Is there a difference in user POV?

  The + said 1830 kB/sec, which equals 1.8 MB/s. You do not understand that?

• Can you change the type of device to 'USB Raw resource' to GPIB controller?

  I'm trying to configure a GPIB FL Contec GP - IB (USB) controller in MAX.  I could so he can register through the creation of a pilot of the Assistant driver VISA, but it fits as a "gross resource USB" rather than as a GPIB controller.  I can send and receive information from the controller, but it does give me an option to search for connected devices of GPIB communicate with them.  Is it possible to change the type of the device, maybe by manually changing the driver created by the wizard of the NI-VISA driver?  Thank you for your time.

  N ° do not use MAX at all. You can just create a GPIB-USB controller on your own. You should contact the seller.

• How to use traditional nidaq with a USB-GPIB installation

  Hello

  When I tried to install the interface GPIB-USB on my computer it tells me I must uninstall nidaq traditional, but I need nidaq traditional also.

  Is it possible to have both installed and functional? Is there a work around?

  Help, please... Thank you

  Darryl Huggins

  Thank you for your response Dennis,

  When I went back to look at the message I think he wanted me to uninstall a driver inherited NOR-488, so I advanced and uninstalled.

  But he said traditional legacy of NOR-DAQ. I was unable to see my card GPIB with Max is why I wanted to install the USB-GPIB.

  After installing now I am able to see the card GPIB and USB-GPIB interface. Must of had a bad driver, I suppose?

  So now I will run another test to make sure that NEITHER-traditional DAQ still works also. But so far so good.

  Thanks, Darryl

• Error of Driver GPIB-USB-HS - 10 possibly after Feb Windows Update Windows

  Starting from 17/02/2016, GPIB-USB-HS material (2) is no longer connecting on 10 of Windows using NI488.2 Rev 15 15/8 with the 15.0.1 patch.

  Using VMWare player 7.1.3, the VM sees the material, connects, turn lights and then turn off. The virtual machine shows "Driver error" unable to connect to the USB device. This has been tested with two USB devices that have worked with the same setup for a few years now on Windows 7, 8, 8.1 and 10 using VMate 7.x and 12. xs

  Possibly this is related to the last update of Windows,

  Repair, or a full installation of rev 15 NI488.2 solves this problem.

  VISA still works via TCP/IP.

  Any thoughts will be greatly appreciated.

  Update: the pilot is still alive.

  The latest version of Windows, which has been applied to the host system 05/03/2016, restores the driver under the guest virtual machine feature. Revisions to operating system host and client are now at 10586.122.