OR scope Soft Front Panel fails to load

Hello

I use the scope Soft Front Panel OR with my USB NI 5132 for some time successfully. However, recently it has stopped working completely - seems to load a bit then fails before you even open the screen. The same thing happens in MAX I did all the updates critical, uninstalled then reinstalled NI Scope, uninstalled Labview (the only thing I had changed after the last time, I know that it worked successfully) and checked the nitaglv.dll library was in the right place according to this post: http://digital.ni.com/public.nsf/allkb/63739991438EC593862579C6007301EC

So far nothing's worked. I NI SCOPE 4.0 and NI-VISA 5.3.0 installed, and the computer could see successfully the digitizer USB 5132 Max after the relocation OR scope, well that the flexible façade does not always load and making the Panel test Max also does not.

I have attached a picture of the screen to load before it disappears so that could provide clues.

Suggestions?


Tags: NI Products

Similar Questions

  • Usability is NOR-SCOPE Soft Front Panel for the PXI-5154?

    I am plans to use the PXI-5154 with his NO-SCOPE Soft Front Panel in a product to test instrumentation. Our past experience, our users need an on-board scope that is easy to use which does not load the CPU. In most cases the scope will be used to check a transitional type of pulses. So, the amplitudes and rise times are essential to ensure compliance with ISO standards. The ability to capture, store and recall traces of reports is important, as well as the ability to perform simple and reproducible follow-up measures. We don't expect our users to have to program the scope; "give me the waveform.

    Does anyone have any comments on the usability of the NOR-SCOPE Soft Front Panel? How to compare with other soft scopes?

    Hello!

    The scope Soft Front Panel is very user friendly and able to load/save waveforms, Load/Save settings and make the scalar measures.  I've attached a screenshot of what the front soft worn looks as well as a link to a help document on the high speed digitizer HELP.  Information on the scope Soft Front Panel lies in this document and can be found under the tab content in the configuration tree (NI - Scope Soft Front Panel help).

    Help of digitizer OR high speed

    http://digital.NI.com/manuals.nsf/WebSearch/2123F564C6DE7B27862574DE006915DE

     

  • OR-SCOPE Soft Front Panel errors

    I can't capture a square wave 10 kHz using NOR-SCOPE FPS.  The error that I get for the manual config and auto-setup is-200580 requested is not a valid Vertical offset.

    Max test panel can capture the signal without errors.

    My setup is PXI-5154 Slot3, chassis PXI-1031DC, Windows Vista, LabVIEW 2009, MAX 4.6.0f1.  Entry test square wave 10 kHz, 4Vp - p connected to Ch0 BNC 5154.

    Hi bmann,.

    What is the descriptor of the resource able & Automation Explorer (MAX) for this device?  Is it the same as other devices that were previously on your system?

    The 5154 can't stand the vertical offset, but other devices (for example the 5152) support vertical offset.  The NO-SCOPE Soft Front Panel (SFP) will use the resources descriptor to identify devices.  If no configuration is not found for a device with a particular resource descriptor, then the FPS will run an automatic configuration on the device.  However, if the FPS is a previous corresponding configuration with the same resource descriptor, it will attempt to use this same configuration.  This is where I believe you can receive the error.

    If you have a 5152, you can check the "vertical offset" parameter in the "Device setup" window - looks like this is the setting that attempts to commit to the 5154 the SFP and the NOR-SCOPE driver is throwing this error.  For a 5152, this parameter should appear, but the 5154 this setting should not appear.

    Could you try to re - appoint the device in your system for something unique?

    Let me know if it helps.  If not, it could be another question - let me know what version of the driver NOR-SCOPE you have installed if this is the case.

    -Andrew

  • OR-SCOPE Soft Front Panel

    Hey!

    How can I include the "impedance" and "Probe atténuation" options at the front view of NOR-SCOPE?

    Now, this option run "Edit-online Device Configuration"!

    Thank you

    Patrick

    Hi Patrick,

    the soft front panels are demo applications for our various modular instrument drivers. We do not distribute their code, nor can you change their GUI.

    If you are programming with LabVIEW I would recommend that you build your own version of a scope to start with an example of our example search tool (help-> find examples). A good starting point would be the Acquisition of niScope configured EX example which also gives you a good overview of how to use the scope pilot.

    If you have more specific questions do not hesitate to ask!

    Best regards

    Peter

  • Options OR Scope Soft Front Panel

    Hey!

    How can I include the "impedance" and "Probe atténuation" options at the front view of NOR-SCOPE? Now, this option run "Edit-online Device Configuration"!

    Thank you

    Patrick

    double post

  • Need the block diagram of NOR-SCOPE Soft front Panel


    I doubt that the code that is available - it can not even be written in LabVIEW.  Examples of NO-SCOPE that are provided with LabVIEW (look in the Finder example under hardware input and output-> Modular Instruments) illustrate all the available functions, and it can be an example that works as a starting point for you.

  • Switch Soft Front Panel, active device classified

    I have a with PXI chassis modules, two switches PXI-2350.  Using the Soft Front Panel switch, it seems that the names assigned to the list of active device (both 2350's in this case) are backward, what to expect.  Is there a way to reassociate those names to the 2350's physics?

    Thank you

    Confustus,

    It's an interesting question that I've never seen before, your devices in a Soft Front Panel should be linked to features like labels in MAX. I was wondering, when you say "we can select using MAX, a road that connects the power supply to the digital multimeter using"Switch 1"(for example), and we can see the voltage reading show on the Soft Front Panel 4071 as planned", what you mean exactly? If you had to choose your hardware device, and then click test panels, the NI Soft Front Panel load switch. Are you saying that when you choose test panels and loading Switch Soft Front Panel of max works as expected, however the application outside opening MAX does not work?

    Or are you talking about the Test panels you open in NI Switch Executive? The test for NI Switch Executive panels refer on behalf of virtual device NI Switch Executive, not the DAQmx device name. If you had named the name of the NI Switch Executive virtual device in the same way, that could be part of the confusion of the problems that you see. See the images below:

    NEITHER DAQmx Test selection panel that leads upward.

    Test NI Switch Executive Panel allows this. If these names are similar, I can see how that might be confusing.

  • OR DC Soft Front Panel, minorbug, small bug with the PXI-4110

    Hello

    The NI DC Soft Front Panel V14.0, with the PXI-4110, scrolling to negative tension, works as expected to-10V, but then returns to 0. If we change from - 1V procedure, it goes...-8-9,-10, -1, -2... instead of-8-9,-10, -11, -12...

    Everything about her, a simple thing that I miss is a switch for all three voltages.

    (Also, IMO, it would be logical for negative tensions with the arrow pointing down, not more).

    My 2 c

    Hello Janaf,

    I completely agree with two of your statements, I tabled a report of corrective measures that you can monitor in the next versions of DCPower to see if this is fixed with the FPS. CAR number: 512257

    I've added notes that only manual insertion of numbers - less than 10 works and that it was not logical to use arrow increment or upward arrow to reduce the output voltage.

  • OR SWITCH Soft Front Panel

    Hello

    I have a few questions in the following way:

    1. After installing the Switch Executive 3.6 (evaluation software), I have very large window for OR Soft Front Panel SWITCH to cover all 4 monitors. It is difficult to see. Do I have to uninstall 3.6 Executive switch (software evaluation)? We don't need that much. Is it safe to uninstall?

    Could you give me the solutuion to configure on the previous setting the Soft Front Panel, released only to a single monitor.

    2. what the Panel "pxi-2720" test should be at MAX? If I click on the test Panel, 'Switch Panel Soft' appears with the topology - '2720-independent? It looks like swich instead of test programmable resistance. Is - this Panel good criterion for pxi-2720?

    3. for NI PXI 2571, I SH200LFH-4xDB50F-C cable to connect to the terminals and tested the switches. I found the NO0 (P1 pin2) - COM0 (P1 pin1) connection is not working while others work. That is reserved by something else? I have test by exchanging terminal blocks, but the result was the same.

    I'm waiting for your answers.

    Thank you

    Insuk

    Thank you!!

  • LabVIEW version of the source code of the NOR-DCPower Soft Front Panel

    I work with an SMU NI PXI-4130. There is a front panel soft exe called the "NOR-DCPower Soft Front Panel" that can be used to control the instrument. I was wondering if there is a version of LabVIEW source code for this driver?

    Jim,

    as much as I know there is no LV source code provided for the Soft Front Panel. But there are a few examples of LV, which will be close to the characteristics of the SFP. So I suggest to you to dig in the examples you find in the Finder of the example.

    Input and output hardware > Modular Instruments > NI-DCPower.

    hope this helps,

    Norbert

  • Panel fails to load on ID CS6, Win 7/8

    Hi all

    I'm developing an extension Flex for InDesign CS6 using Flash Builder 4.6, Extension Builder 2.1. The user interface is simple, there is a button. On the full application, I just to initialize an object of a class. My problem is that sometimes, the button on the right panel does not load. For eg., if I close the application ID without closing the Panel and then reopen the application, normally, the Panel should load fine with its components. But here, the button is not visible. I have to close the control panel and then open it again to get the button to load. There is no specific pattern. I tried to find the problem by implementing of alerts in before initialization, initialize, creating full and events full app. But these events are not triggered.

    On further testing, I have found that if the Panel is moved (eg. slide panel with the mouse), the Committee charge instantly. Is there a bug in InDesign CS6, because the extension does very well in other versions? Additionally, this problem occurs in Windows 7 and 8. It works fine on Win XP. That Mac OS transfers very well.

    All I can do about it?

    Thank you.

    Hello

    I found a solution to my problem. I just had my Panel on and outside visibility, and it worked... Note that this inserted a crash for ID CC...

    If someone finds a more appropriate solution for this please let me know.

    Thank you.

  • How to disable the automatic launch of Soft Front Panel?

    So, I foolishly decided to my NO-Scope to launch automatically when I insert the USB cable to my PC.

    I can't figure out how to disable this option. OR Scope does not appear in my AutoPlay settings in Control Panel.

    I use Windows 7.

    If you know the answer, I would like to know also. Thank you.

    Right, I do not expect the device appears in the AutoPlay list since our driver does not AutoPlay API at all.

    I managed to reproduce the problem that you have on my machine, and I was able to fix, follow these steps:

    1. disconnect the equipment

    2. right click on the icon "monitor of devices OR" in the system tray

    3. Select 'clear all device associations '.

    4. click on "Yes" in the dialog box "are you sure that...". ».

    Turns out that the monitor of devices OR implements its own custom 'AutoPlay' form that is not connected to the Windows API at all.

    I hope this helps!

    Kind regards

    Nathan

  • NIVXD128 Soft Front Panel for DIO - 128

    Dear all

    Where can I find an Installationsfile for the NIVXD128 of Panel or how should I configure the DIO-128 with the NOR-DAQ Configurator for use with façade?

    Thank you

    Hi Blias,

    I m not very good if you asked the attachment, but maybe it's what you need!

    BR

    Alex

    PS: as it is not allowed to join .exe, just remove the '.txt '!

  • NI DMM Soft front panel detects any nor-dmm

    Hello

    has anyone seen this failure? I have can´t open sweet face before you configure the DMM. I tried to reinstall the VISA and NOR-DMM without success.

    Thank you

    Robert

    Robert,

    What happens when you run the self-test on the PXI-4072 in your system?

    Also, if you rename the PXI-4072 another name ("4072", for example), it works?

    4072 in your system looks like it is may not be installed correctly. The icon it shows in MAX is PXI generic icon, not on the icon that should display devices OR DMM (my apologies, but I don't remember the terminology). In addition, it should show the 4072 as 3: NI PXI-4072 "PXI-4072. Your is showing that 3: 4072 "PXI-4072. See the image below for how it should look like:

    Please let us know if that helps.

  • NOR-DMM vs IVI - DMM - Soft Front Panel

    Hi all

    I've developed a test application that will subsequently use a PXI-4070 DMM (currently simulating it OR max).  I used the IVI DMM functions, but ran into a problem when I couldn't do a diode test (diode test is apparently not officially normalized according to by IVI yet).  So I've been using the functions OR DMM. Essentially, it's a pretty seamless transition, but there is one thing that I was not able to replicate with the NOR-DMM simulation I could do with the IVI - DMM.  When I used the IVI - DMM features and ran the VI, an open popup that enabled me to get into the simulated value I wanted the DMM to read.  I can't get this to work with functions OR DMM.  Is this possible?  If Yes please let me know how to activate it.  Thank you.

    GSinMN

    The advanced simulation exists only on the level of Class IIA (IviDmm) driver. Class IVI drivers implement the functions of simulation using pilots of the simulation. IVI Compliance Package (PIC) installs a driver simulation for each class IVI driver. Each pilot simulation of plugs for the pilot of the corresponding class and performs the simulation of flexible output data. The NOR-DMM is a specific driver that supports the DMM series NOR and therefore does not include the functionality of advanced simulation.

Maybe you are looking for