Output a TTL HIGH 10 usec via the PFI port on AWG signal generator

LV dear community,

I want my signal generator (PXI-5422) to produce a pulse of 10usec with its PFI1 range each time that a wave of exit CH0.  The frequency of repetition of the CH0 impulses and the port of PFI1 is 10 kHz.  Is it possible for the signal generator automatically generate this HIGH TTL signals for usec 10 on the PFI1 line all at the same time produce a long-wave 100 usec?

Another approach, that I'm considering is to re - route a pulse of RTSI1 (10usec) from an FPGA and output via port PFF1 of the GTS. However, I doubt that this is possible, as the HELP MENU for the working group said that the report can only occur when the Working Group is in "idle" mode.

Any help will be greatly appreciated!

Have a nice day I have attached a diagram of operation that hopefully, explains what I'm trying to do a little better.  Once again thanks for looking!

-Daniel

Hi Denn_Mann,

To get around the limit of 320ns, you should be able to use scripts with the FGEN markers to achieve your goal. Anything you want to do is use of script with markers in alternating mode. You may want to toggle high then low rocker after the number of samples you want pulse is high while your signal is present. I've linked some information below that should be good resources for script for you if you are not familiar.

Trigger on the arbitrary signal generators and advanced waveform sequencing

Creating an event marker in Script Mode

Script mode

Example of the expedition: "Fgen Arb Script.vi.

Kind regards

Ann Travis

Tags: NI Hardware

Similar Questions

  • to detect the meter output via the parallel port

    I need to detect the meter count trigger, to perform an operation every time. I think passing the input signal pins (pins of status or control). The meter uses is omron H7EC.

    I lowered the voltage of 24 V to 5 v with resistors.

    But I can't get the entry via the parallel port.

    All the stems of my status are still high.

    What should I do, please help.

    In the parallel reading write loop.VI, the splash screen is attached.

    I suspect the entries on the parallel port pins have a resistance low pullup to 5V, so they tend to float high (logic 1).

    Try to add a 4 700 Ohm resistor between pins of entry and mass of the parallel port, see if it then reads down pulldown (logic 0). If so, then keep the resistance in place and connect the signal of 5V that you want to monitor at the entrance.

    -AK2DM

  • How can I get multi channel audio via the HDMI port on an early 2015 MacBook Pro?

    I try to get the 7.1 audio channels to flow from my MacBook Pro to a cinema set up. The display works fine now I plug the HDMI in however the sound still Mac speakers. I checked the settings and no HDMI output is available. An airtime option is available, but that returns only two channels as a maximum to the receiver. When I go to the configuration of the source on the receiver it receives video at 1080 p 60herts however it is specifically stated No Audio from the Source.

    Also, I have connected my iPhone 6 s more using an Apple through the same HDMI cable adapter and it works perfectly. We also use HDMI with our PS4 occasionally and it works perfectly, even with the 3D.

    Thus, the MacBook Pro is early 2015 with an i5, the receiver is a Harmon Kardon AVR 2700 (we run 7.1 channels of this) and we are connecting via the HDMI port through a 50 ft HDMI before. The receiver sends the audio to a projector with 1080 p 60 hertz if it changes anything...

    Also if it helps the receiver supports dts - hd master audio decoding, Dolby True HD/Digital Plus decoding, HDMI 1.4 (HDMI is compatible 2.0), as well as multi-channel input and PCM and linear PCM.

    I use a "Behringer UCA202' audio device I bought on amazon.com for only $29.

    It works very well for the audio 5.1 or 7.2. Works connect optical toslink. Just plug it into a usb port on your Mac and a cable optical toslink to your AV receiver.

    My Yahmaha 7.2 audio/video receiver is measuring process the digital signal in THX, DTS, Dolby digital Pro logic, a cinema, etc.

  • I want to detect and use the video entering via the HDMI port on the computer. I was told the HDMI port was not set, but I can't seem to find the signal or the video.

    I want to detect and use the video entering via the HDMI port on the computer. I was told the HDMI port was not set, but I can't seem to find the signal or the video.  Any suggestions?

    As Tom SC replied, you must contact the company that manufactured your computer.  In general, the ports HDMI on most computers is an out-bound port, send video / digital audio output.

    You should probably use a video capture card that can capture from HDMI source,

  • Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

    Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

    What Mac? (details)

  • Transfer an image via the serial port of PC to PC

    Hello world

    can someone help me to transfer an image file to another PC with Labview via serial port?

    I tried to use the IMAQ functions to decode the image to a string. but there is a problem at the receiving end to retrieve the image.

    is there an easy way to just sent and receive an image via the serial port file?

    Thanking you in advance.

    Morgane

    Hello

    I love people who love to learn. Thanks for listening.

    I updated read and write Subvi is because I believe keeping simple and straight threads more readable program and less bugs remain.

    Even better, my eyes straight lines i do not get tired too soon.

    good luck with your program.

  • BlackBerry Torch 9860 smartphones does not connect with the pc via the USB port.

    We have a new Torch 9860 which does not connect with a PC via the USB port.  What should do?

    SlaKir wrote:

    The answer is YES

    Well, then your USB port is likely.

    Restart the PC and BlackBerry (with smart BlackBerry power onthe phone, remove the battery for a minute and then reinsert the battery to restart).

    Then, connect with the USB cable and a rear main USB port at the back of the PC, not a front USB port.

    Hear a ringing or sound from the PC indicating that the BlackBerry is connected?

    Start the BlackBerry Desktop Manager software. Give it a minute to recognize the connected BlackBerry device... you see the code PIN of BlackBerry on the PC in the BlackBerry Desktop software?

  • Problem after connecting via the USB port of the printer. Error 0x0000007a

    Recently, I plugged my HP Deskjet2360 printer via the USB port on my HP laptop (running w7 Home premium 32-bit) and can not print at all. When I try to print a test page I get the following message ' operation could not be completed. Error 0x0000007a. Operation failed.

    My usual Setup is to have my printer connected to my desktop (Windows XP Pro). My HP laptop is connected via a wireless connection to my home network, which is also connected to my desktop computer. Of course, this means that I have the office turned on to be able to print from my laptop.

    Everything worked great until I decided I'd rather have my connected printer to directly to my laptop via USB.

    When I connect the printer via the USB port on my laptop, windows installs the software and reported no problems. Yet when I try to print a test page, I get the mentioned error. When I then reconnect the printer to the desktop and try to print a test page to my network, I get exactly the same error message. The office and the printer still work fine, it's just that I can't print from my laptop.

    I uninstalled and reinstalled the printer on my laptop with the USB connection and the network, but it still does not work. The resolution of the problems on the laptop reported no problems, and the printer is set as default printer. I also get an another error msg when I click on the Preferences button in the printer properties: address of the 0x5aeba4f1 function caused a protection fault. (code 0xc0000005 exception) Some or all property pages cannot be displayed.


    The only way I found to get around this is to use windows restore and restore my laptop before the point when I connected the printer via the usb port.

    Any suggestions?

    Hello
     
    This error 0x0000007A describes the data area passed to a system call is too small. ERROR_INSUFFICIENT_BUFFER
    You can try to uninstall and reinstall printer driver and check if that helps.
     
    Here's how you can do:
     
    1. open programs and features by clicking on the Start button, clicking Control Panel, click programs, and then clicking programs and features.
    2. Select a program and then click on uninstall.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
     
    After you have uninstalled the driver to restart the computer, this should install it the appropriate drivers for it. You can also try to download the latest driver from the manufacturers website and install it.
     
     
    Kind regards
    Umesh P - Microsoft Support
  • MP3 player via the USB port (no matter which), it keeps coming back as the "Drive is not accessible. Access is denied. "

    Hello

    So, here are the problems I encounter, and what I did to try to fix myself.
    Whenever I try to connect my MP3 player via the USB port (no matter which), it keeps coming back as the "Drive is not accessible. Access is denied. "  This same thing happens everytime I try to put an SD card in the SD card slot.  However, despite this, I can plug my USB mouse and use it, as well as the keyboard and it records only.  I can also use the HDMI port to use my TV as a second monitor and, also, to record that.
    What I did to solve the problem, it is to restore the system to the previous times before that happened, did not.  I also went into the Device Manager and uninstalled and re installed, USB and SD card drivers.  I also tried something in the sense of taking control of the files via a right click on a folder and go to properties and then security and to the 'advanced settings', the problem with this situation is that I can't in readers at all.
    I am currently running Windows 7 (64 bit) on a laptop Lenovo, the computer itself is actually only a few months.  If someone knows something about this, please let me know.  Thanks in advance.

    Hello

    1. What is the number of brands and models of MP3 player?

    2 are logged in as an administrator on the computer?

    3. are you able to use this device on another computer (not Windows XP)? The MP3 player or SD card already worked on this computer?

    4. Once you get this error message? Do you get this error when accessing the mp3 player and SD card on Windows Explorer?

    Run an antivirus with Microsoft Safety scanner scan and make sure your computer is virus-free.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

    Response with more information to help you.

  • Animate the CC of the tests on the device via the USB port or the publication of device does not

    Without a paid with Apple Developer account (waiting to have in fact my first AIR for iOS app works correctly), I created the .mobileprovision and .p12 files successfully in Xcode. With these I figured out how to debug in the Debug of Animate version iOS Simulator > DebugMovie > iOS Simulator but I can't debug my device (iPhone) via the USB port. ("Impossible to install the application. Make sure that the selected devices are connected. ") Connected and on. No problem with the available memory.

    Past the other road, I published with success (he said) but my iPhone will not complete downloading the app in iTunes and even less using the 'post publishing' check in settings to install on my selected iOS device of publication. It is there no dialog, no explanation why... simply "the application was published successfully."

    I moved the .ipa file in iTunes and on my device. It says it is syncing but then goes with anything. I once accidentally dragging the icon of my iPad where it has at least tried to install it. The dimmed icon appears on this device with "install...". "below, but it was not built for the iPad, so I trashed it after a few hours.

    I have watched the video of Adobe and don't see what I'm doing is different.

    In Xcode, there is a window of devices. You can select your iPhone and check requests in this regard. Try dragging the IPA in this list. It may still fail, but I hope that Xcode will give a better error message.

    It is a faster way to much to get applications on devices using iTunes. If it does not copy OK you can then try remote debugging in Animate and then open the application. The IP address of your computer, you must have this ready to type in.

  • Problem connecting to HP DJ5900 via the USB port on the router

    HP DeskJet 5940, MacBook Pro, OS x 10.6.8.

    I want to connect the DJ5940 through my router (Speedport W723V) via the USB port.

    I see that the printer is connected to the USB port of routers and adding a printer on the MBP works.

    However, when I try to print, printing dialoge sas is printing (full % increases), but nothing is displayed and the status of the printer finally chnges for "printer paused".

    Is what I'm trying to do possible?

    Dean,

    Thanks for your help, but I went in a different direction: the Speedport router is EXTREAMELY oriented Windows, to the extent that it has nothing in the documentation to do anything with a Mac, so I've dug a former print USB/Ethernet of Axis Communications Server. At least 7 years old and no documentation, but connect to its IP address allowed me to set it up, and Macs connected to it directly.

  • iPhone 7 will not play audio via the USB port on the car.

    When I plug my iPhone USB port 7 more in my car (15 Jeep Grand Cherokee), the artist/song/podcast information appears on the screen, but the sound plays through the speakers of the phone.  I have confirmed that my settings are all the same as they were on my 6s, who played without any problems via the USB connection.  Bluetooth streaming works fine - no problems at all.  Any ideas, or is this a problem similar to that people have with CarPlay?

    Welcome to Apple Support communities, kevo.mac!

    Congratulations on your new iPhone 7 more! I see that you connect with your Jeep Grand Cherokee using the USB port. Everything seems to work fine, except that the music plays through the phone instead. I'll be happy to help you to get this working.

    Help to connect your iPhone, iPad or iPod touch with your car radio

    If you are using USB playback

    Restart your iOS device and your car.
    Connect your iOS device to another stereo USB port (if you have one).
    Try another USB cable.
    Update your iOS device.
    Install the updates to the firmware of your car radio.
    Test of audio playback from a different application. If you can not play audio from a specific third party application, contact the developer of the app for help.
    If you can not play audio from an app Apple, contact Apple technical support.

    Enjoy your weekend!

  • How can I install Firefox on Samsung S5 via the usb port on my PC

    You don't have a Google account - don't want no one. Want to just Firefox. How can I install via the PC's USB port. I have the developer options enabled.

    You can use the Aurora of Firefox for Android version. https://www.Mozilla.org/en-us/Firefox/channel/#developer

  • Satellite L500 - high-pitched noise when the USB port is in use

    I have a Satellite L500-1ZP, aged from 1 month. When I connect a usb key or other device in my usb port, the laptop generates a high-pitched noise.
    The sound is not strong, strong but enough to irritate me.
    When I disconnect a device, the sound disappears.
    The sound is also there when I disconnect my laptop to the grid form.

    This is a common problem and can it be resolved?

    To be honest I don't think that this is a common problem. Is that what you found more threads with the same description of problem?
    The same happens when you use the available USB ports?
    You can locate where this noise is coming from? Maybe the speakers?

  • Satellite P750 - unable to connect an external display via the VGA port

    Hi all

    My problem is the following:

    I tried to connect my P750 (running on W7 x-64) an external display using the VGA cable port. Unfortunately, these devices recognize my phone. Laptop does not recognize the external display, you can see in the graphics settings as additional display, but the screen shows "no signal".

    The computer always identifies the screen correctly, so it seems that there is communication from the screen to the PC, but not the reverse.

    This has been verified with 3 separate screens and television - still the same. All the screens work properly with the other PC.

    I already have:

    -try to play with FN + F5 / "windows" + buttons P - no change
    -install the latest drivers BIOS and video site Web from Toshiba - no change

    Suggestions how to operate? Is it possible that the VGA port is faulty?

    Thank you in advance.

    Hello

    You have the same problems with a HDMI output port?
    Usually, you don't need to change anything to get the external monitor works.
    Press Fn + F5 several times until the monitor RGB (VGA) was selected
    Since you can choose an HDMI output too, you should pay attention to this option.

    Have you tried to change the resolution before using the Fn + F5?
    It s worth a try

    Last but not least, you could set the default BIOS (press F9 BIOS and save the changes by pressing F10). But I don't very well if the BIOS contains some parameters of port RGB (VGA) m

Maybe you are looking for

  • poor performance analog output (error 200018)

    Hello.  I have a 6124 SMU Board with controller real time SMU-8102.  the Council is speced to MECH 4 analog outputs. / s (one lane), but I have problems to operate at anything beyond about 500 kech. / s.  I enclose my example below program.  If I put

  • How can I replace a BONE in a multiboot

    I have a triple-boot PC (don't ask) with 7-Vista-7.  When 8 came out, I replace the Vista partition with 8.  I don't need help with installation, because I know that I just follow the custom installation path.  My question concerns the Elimination of

  • Signature tool is not woking and he hangs everything by signing

    Hello Get the BlackBerry signing keys (.) File CSI) supports the development of BlackBerry applications. When I try to install those signature keys (RRB, RRT, CPR) in my eclipse these keys have been successfully registered. But when I sign. COD file

  • I have windows haveremoving 10 to return to the original

    comes to be upgraded to windows 10 I hate, how to return to my earlier version of windows without losing my data

  • Basic question on Cisco GET VPN and MPLS

    Hello Imagine the Organization a (4) sites connected via MPLS, those not managed. If the customer wants to implement the Cisco VPN, is there no restrictions typical of the coast ISP or should I rely on any feature or the configuration of the ISP in o