Overload

Similar Questions

• Messages from system overload.

  I've been using logic 9.8.1 w OSX 10.8.5 (2.2 Ghz Intel Core i7, 8 GB 1333 MHz DDR3) for a long time without problem.  Lately, even on simple projects, I get "system overload.  The audio engine was not able to process all the required data in time"messages.  I tried to reboot the computer with no luck.  It is not my audio interface.

  And nothing has changed, always using the same system?

  Is your drive nearly full system hard? How much free space on the system drive?

• Disk is too slow or overloaded system

  In one of my projects, every time, he gets at the helm of the 9 it still gives me the "disk is too slow or overloaded system' warning. I have 24 GB of RAM, 6 core 3.33 ghz processor, my project running on an external hard drive, and I froze all my tracks with the exception of a few. I'm still all my bounced based vst tracks audio tracks as well. This message appears every time in the same exact spot of the song, which isn't even the most complicated part of the song. However, there is no problem to any other part of the song. I do everything at sampling frequency of 96 kHz, which I regret now and is probably the most problem, but nobody knows what I can do to fix this? Also, I have increased my buffer size, did know of course other programs were running and still nothing.

  Are there audio recorded into your song? If this isn't the case, you can set the 44.1 kHz sampling frequency. The question with regard to your question is: what happens at the bar 9? Try to mute the titles one by one until it clears up the question. A screenshot of your project can also help determine the problem.

• my iphone has got overload, iphone or iphone charger stop charging if it is 100% even if still plugged

  my iphone has got overload, iphone or iphone charger stop charging if it is 100% even if still plugged

  Caused,

  The overloads are not possible. Load is reduced to a trickle charge after reaching 100%.

  

• Smart box overload

  is this my case overload when in the phone?

  I guess you mean will be the case overload your phone, and the answer is no. There are circuits that prevent it.

• Smart battery case overload?

  I have a 6 s and I wonder if the case will my iPhone to overload and break it. Thank you!

  RussellACoyne wrote:

  I have a 6 s and I wonder if the case will my iPhone to overload and break it. Thank you!

  No, it won't. She stops to charge the phone when the battery reaches full.

• Re: Satellite A300-1 MB - processor overload

  I have a problem with the processor for some time now, first I thought the virus but the reinstallation of the Windows Vista Home premium I have the same problem.

  The processor overload even if I play a basic flash game. The same thing with Warcraft 3 and Fifa. Why? I have a Toshiba Satellite A300 - 1 MB T5800 2.0 GHz Centrino. 3 G of RAM Mobile Intel 4 Series Express Chipset Family as a display driver

  Hello

  Have you installed a different display driver? I had a similar problem with overheating and the reason was the display driver. After that, I installed the latest version from the Toshiba site and everything worked properly again! :)

  In addition, I would recommend Notepad using compressed air cleaning spray. This could blow off the dust and it s not necessary to disassemble.

  Here is an interesting article of How To:
  [How to clean a Toshiba laptop cooling system? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=40]

• Is there a risk of overloading a pencil Apple via a USB, rather than in the iPad Pro?

  I just bought an iPad Pro and the pencil of Apple. I understand that the pencil can be loaded without using the iPad. How much time will it take to receive a full charge and is there a risk on reload. Can I plug to charge all night so I have a full load to shoot during the day? Unfortunately, I found no information on this. The booklet that came with it didn't cover this issue.

  I appreciate any help I can get in this regard.

  Is there a risk of overloading a pencil Apple via a USB, rather than in the iPad Pro?

  Lol of course not.

  No company could design a product that would allow it to be overloaded.

• 10.2.1 - system overload problem

  Hello

  I have problems with 10.2.1 not being able to play my existing projects due to system overload, when loaded in 10.2.0 they play absolutely great. So now I have two versions of the software on my machine but am very reluctant to use 10.2.1 for new projects where I'm getting the same problem and cannot use the 10.2.0 project.

  I have included a link to a video to show, I've loaded the song in 10.2.0 and played the "Chorus" section, quit smoking and loaded the same song in 10.2.1 then attempted to play the same section. There is nothing else running on my system.

  I'm on OSX 10.9.5 and have not updated because I use logic every day in my profession and can not afford to issues of upgrading risk affecting my work (the upgrade logic being a good example).

  Help, please.

  https://www.YouTube.com/watch?v=84GY9t_MkhQ

  Kind regards

  Kevin.

  Kevin,

  Even if your video shows the problem it shows what it might because the causes are usually the 3rd party plugins that need to update... or a necessary for your Midi interface update tis / audio for example...

  Hard to say exactly... but I can say Im running in the two OS X 10.10.5 and 10.11.3 10.2.1... here on a test bench several Mac (Mac Pro, iMac, iMac 5K and Mac Mini Server) using Motu gear... with the latest drivers... and I do not see the overloads more that I saw less than 10.2 or 10.0.7...

  When the version of your OS X begins to age, it is possible that trying to use a modern application that is optimized for later versions of OS X, might be the cause... but as I don't have a Mavericks system based on test bench these days, I can't confirm that...

  That's why I don't update the logic or OS X unless I have absolutely or need on my main work here systems...

  Example: Im still running 10.6.8 and LP 9.1.6 as one of my main "workhorse"... as his stable, efficient and reliable systems...

  Nigel

• How I bounce back without having to change the setting of 'Protection against overload only' amateur off EACH time?

  How I bounce back without having to change the setting of 'Protection against overload only' amateur off EACH time?

  This setting should be preserved, once you set it... so I'm not sure why you have to define every time...

  Then... Make sure that you put on ALL the tools of the art of logic in the preferences of LPX...

  Otherwise... you may need to reset the prefs of LPX... Put all the Tools Advanced again and the other preferences you have set... and see if that fixes things for you...

  You can resolve many issues by restoring Logic Pro X back to its original settings. This will not affect your media files. To reset your settings preferences of the user to Logic Pro X to their original state, do the following:

  1. Logic Pro X to quit smoking
  2. In the Finder, select go to folder menu reach.
  3. Type ~/Library/Preferences in the field 'go to folder '.
  4. Press the Go button.
  5. Delete the com.apple.logic10.plist file from the Preferences folder. Note that if you set custom shortcuts, it will reset to the default values. You can export your custom key as a preset before performing this step. See the Logic Pro X user manual for details on how to do this.
  6. If you are having problems with a control surface in Logic Pro X, you can also delete the com.apple.logic.pro.cs file in the Preferences folder.
  7. Restart the computer.

  Note: If you cannot find the files listed above, you don't follow the instructions properly!

• M4100 - 26G - POE - lack of recurring overload on 17-24 ports

  I have a M4100 - 26G - POE that I bought a few weeks ago and I see recurring defects of overload on 17-24 ports only. I used the exact same cables and devices on ports 1-16 and they all work fine, but if I move the cable to one of the top ports this will work for a few minutes then reset due to a defect of overload all few minutes or more. Everything goes well with the cables or connectors, and like I said it works fine on ports 1-16. Ports 1-16 are configured as ports 17-24 in the page web.

  I want to know is if anyone else experienced a similar problem. Specifically, I want to know if it's a defective unit, a hardware design flaw, or a problem with the firmware (version for this model). I tend to think, it's probably a defective unit, but I would not be shocked if it is a firmware issue.

  I want to know because I won't go well the expense by exchanging the unit to the store or swap try it on warranty and get a replacement that is a refurbished, model unless something is actually wrong with the hardware. I don't know that I see myself using more then 16-port POE in the foreseeable future.

  Firmware 10.0.1.27 is now available, and a section in the release notes may relate to this problem:
  

  Someone who goes through this thread who saw this problem, tell us what you find!

  I sold my M4100 - 26G - POE because I needed a job switch.

• Satellite A100-163 - blue screen when the PC is overloaded

  Hi guys!

  I bought my PC not so long ago and it's a machine woderful piece, BUT I have a question that I guess is with my RAM. Whenever my PC is overloaded (when I start a game + my winamp plays and I'm downloading stuff on the internet) I get a blue screen telling me that Windows is dumping some memory etc etc... He suggested to update my BIOS driver as a possible solution to the problem. I tried new drivers from this site, but there is no news yet.

  Any suggestions how to fix this problem?

  Concerning

  KOS

  Hello

  I don t think you will solve this problem by updating the BIOS. It is a new unit and there are more recent version of the BIOS installed.
  In my view, this problem occurs due to running applications. The most games need the full memory performance.
  In this case another application cannot use the full memory.

  In your case, I would check the memory sticks or / and to improve memory.

• Question about the overloading of the battery

  In the past, I messed up my batteries cell phone constantly keeping the battery in the laptop / constantly on the current...

  So I learned my lesson and now I always run the laptop with the battery disconnected... as I rarely go out and need

  I noticed on the Lenovo IdeaPad it has a nice feature to run battery 'Best battery health' that keeps the battery charged at 40% to avoid overload... is without danger if I keep my AC 100% connected all the time WITH the battery as well? I will not damage the battery or it really works and not damage my battery to charge more?

  Thank you

  Hi again Racer,

  I found some information useful for you battery life...

  http://forums.Lenovo.com/T5/IdeaPad-Y-and-U-series-laptops/optimizing-battery-run-time-and-battery-l...

  http://BatteryUniversity.com/learn/article/how_to_prolong_lithium_based_batteries

  Good luck... Zehn

• How NI PCI 4474 DSA detects an overload to the input channel?

  I read "Manual user OR dynamic signal acquisition." It is written that NI PCI 4474 support only digital overload detection.

  Here's my question. What is the detection of digital overload? If an analog signal is already converted to digital signal, it can not be signals exceeds the limit. Or the DSA may already be damaged during the CDA process, if there is surcharge from the input signal. Thank you.

  Hyun

  Yes, the chip has more information about the Board and apply factors of calibration, which is how it can overflow.

  What we call "detection of overload analog domain" requires more equipment (i.e. a comparator circuit) to observe the input signal.  Given that the Committee in question is not a comparator to check the input signal, and the way we want to give the user an idea of whether or not their signal is too large, we simply use the mathematics inside the chip. It's better than nothing.

  Oh, and I should mention that the protection is managed by a completely different circuit.  The specification should say how much voltage you can apply to the Commission before the protection comes into play.

  Germano-

• SignalExpress overload

  
  

  Sdltd,

  I'm leaving the principle of overload on a channel say you if the tension of the string is passed above the Max (42.4 V peak Ridge premium) entry on the PXI-4462 device. There is no material given indicator that tells the computer in any way that there is an entry that exceeds the voltage max. The only way you'd be able to tell if it happened over voltage max would be if the rails of the device to the peak voltage. I wouldn't recommend testing the limits of your devices like this as this could damage your device. What you could do in SingalExpress would be to set an alarm, then what's the channel exceeds a certain tension, lets say 40 V pk at differential pk, acquire the DAQmx would stop. LabVIEW SignalExpress 2010 has features for alarms, is not the case with the SignalExpress THE.

• How to overload a sequence?

  I want to overload the sequences TestStand operation can be overloaded in other programming languages.  By overloading, I mean I want multiple sequences with the same name and different parameters.  He appealed and enveloping the function much easier and cleaner.

  For example if I need 3 parameters for specific action, but I only have 2 and want to use the 'standard' for the 3rd parameter value, I take steps to get the third parameter inside a function with 2 parameters, and then call the function with 3 parameters.

  I put the standard quoted value because most of the time it will not be a digital fault.  It could be a piece of information obtained from a network or a field of another parameter, or anything really.

  I think you are badly understand what I'm telling you...

  The default values for common data types are:

  Boolean = False

  Digital = 0

  String =' '

  However, this is not what I am referring.  When you add a parameter to a sequence there are 4 columns: name, value, type, comment.  Under the comment of value that you put a value that you want to be the default. Let's say you have a digital set called Foo and you put 10 as value.  Now when someone puts down a call to this sequence sequence and they check the default zone for the parameter Foo the value will be 10 when he enters the subsequence.

  Edit: If you really want to try to check if the default value has been used:

  RunState.CallingStep.Module.AsSequenceCallModule.Parameters.Item (X). UseDefaultValue whre X is the index of the parameter you want to check.

  See you soon,.