P7 - 1126 s WIN8 upgrade worked fine until I got clean install. Now stop and sleep do not work.

Similar Questions

• my wireless was printer was working fine until what I used it to scan - and needed to use a cable for s

  Hi, can anyone help? My wireless was printer was working fine until what I used it to scan - and needed to use a cable to do so. I can no longer print wireless, Iv'e disconnected from the PC to the printer as cable seemed reasonable. What should I do? Thanks in advance

  What printer you are using?

• Upgrade of Windows 8 Blurry\Fuzzy Pro install dvd screen and a flash drive.

  Upgrade of Windows 8 Blurry\Fuzzy Pro install dvd screen and a flash drive. Each screen is blurred during the installation. Managed to get

  It is installed. A great until I had to reboot after the installation of windows updates. It starts with the first good looking for Windows 8 logo then

  the monitor turns off and the computer is still running. Reset and I get the windows repair screen. Sometimes, his clear and sometimes

  its blur. I have a motherboard Asus M2N with a Nvidia geforce GT 240 video card. I'm guessing that the windows install 8 pro and pre of initialization

  use some funky video drivers before windows loads the correct nvidia drivers. Microsoft needs to do a better install disc that allows to display the

  graphics correctly. Windows8-UpgradeAssistan does not really check very good material. I ran the windows 8 developer preview and it

  had no problem. Y at - it a hope?

  Hi SteveSimmons,

  I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

  I suggest you install the latest drivers from Nvidia geforce GT 240 for Windows 8 from the link below video card:

  http://www.nvidia.com/download/index.aspx?lang=en-us&ptid=1&PSID=52&PID=0

  I hope that the information above helps you.

• Installed MAMP 3 and I can not localhost to work

  I just installed MAMP 3 and I can not get the APACHE server to work now. It seems that they have added the Nginx port, while it was just Apache to port SQL. When I try to set the Apache port to 80 and SQL to 3306, who worked before, he said "there is a problem with the ports on the server. Each server must be assigned a unique port. Please check your configuration. "

  Apparently, the ports of Nginx and Apache cannot be the same. However when I change the port of Nginx to another (example to 8888) it simply stops the Apache server. Any help on what to do? I used MAMP for years and this is the first problem.

  Here is a screenshot of the port settings

  

  It is fixed. Just for someone else, I had my answer here: Port Changed to 80 after installing MAMP, but does not start the Apache Web server. | Treehouse Forum

  Then, I changed the port of Nginx at 8887. Apache is 80 and MySQL is 3306.

• I can't install the new application on my iphone 5s revel.  I tried to install the update, and that did not work.  I deleted my app and rebooted my phone and tried a clean install and that no longer works... Help!

  I can't install the new application on my iphone 5s revel.  I tried to install the update, and that did not work.  I deleted my app and rebooted my phone and tried a clean install and that no longer works... Help!

  Please see the post below updates on the issue of the revel facilities:

  Problem installing Adobe Revel 2.3.2

• I had to do a clean install, now I have problems to register upgrade

  Due to a problem of Windows Explorer that kept crashing I had to do a clean install of my Vista Ulatimate. Now it doesn't let me save the program. I've tried doing a reinstall and that didn't stop my crashing Explorer. Forum was probably fifty solutions to this problem, which has not worked for me and Microsoft told me they didn't help me solve with out charge me, so now they're trying to me live in the purchase of a new program or the upgrade and that sucks.

  You MUST start the process after WIndows starts - do not have the DVD in the status bar when you start, but insert once started.

  To be honest, you should have settled this first thing - now, all you can do is try to uninstall SP2 and hope it works, but be prepared for a double-full installation if it does not work properly.

  http://www.winsupersite.com/article/product-review/Windows-Vista-installation-Super-Guide-part-3-clean-install-Windows-Vista

• Side-by-side configuration is incorrect, after the upgrade from Vista Business to Win7 for AutoCAD, Revit (Autodesk) and most but not all Adobe programs and a few others.

  I have seen many other people having this problem, but none of the soultions has solved the problem.

  After the upgrade to Win 7 Vista Business company. a number of my programs will not work. a mistake

  "The application failed to start because its side-by-side configuration is incorrect."

  train the Viewer even I get this

  Activation context generation failed for "C:\Program Files\AutoCAD 2010\acad.exe". Load Assembly Microsoft.VC90.MFC, processorArchitecture = "x 86" publicKeyToken = "1fc8b3b9a1e18e3b", type = "win32", version = "9.0.21022.8" was not found. Please use sxstrace.exe for detailed diagnosis.

  I tried to uninstall completely all Autodeck and re install but that has not worked.

  Install the Visual C ++ 2008 Runtime.

  Package redistributable Microsoft Visual C++ 2008 (x 86)

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=9b2da534-3e03-4391-8a4d-074b9f2bc1bf&displaylang=en

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Dell Dimension 9200. The orange light flashes. Power disconnect day + this market but stop and it will not work unless that unplugged for a day

  Flashes orange and no lights on the front panel next to the USB ports. (see amber light on motherboard, power button / stop 15 sec + he disappears, but the computer does not start, a few times the fan turned on couple seconds), initially it used to go in the cycle (starts for about 3-5 seconds and stops) several times and the flashing yellow light.

  If I unplug the power cord for a day + and try, it worked, stop and restart immediately worked too but when I shutdown and come after a few hours, it will not start again (power plugged).
  Disconnect the power supply for a day + new and it worked once tried.

  I did the reset by pressing the power button / 15 sec + but no luck. Until a day + unplugged worked so far about three times will try again tomorrow and see what happens if I don't stop the computer ever.

  What a PSU or of the motherboard problem or some other problem? Hope it can be fixed.

  Rav96

  Flashes orange and no lights on the front panel next to the USB ports. (see amber light on motherboard, power button / stop 15 sec + he disappears, but the computer does not start, a few times the fan turned on couple seconds), initially it used to go in the cycle (starts for about 3-5 seconds and stops) several times and the flashing yellow light.

  If I unplug the power cord for a day + and try, it worked, stop and restart immediately worked too but when I shutdown and come after a few hours, it will not start again (power plugged).
  Disconnect the power supply for a day + new and it worked once tried.

  I did the reset by pressing the power button / 15 sec + but no luck. Until a day + unplugged worked so far about three times will try again tomorrow and see what happens if I don't stop the computer ever.

  What a PSU or of the motherboard problem or some other problem? Hope it can be fixed.

  Rav96

  A flashing orange power LED, usually indicates a power supply problem power, given the age of the Dimension 9200, which is highly likely.

  Try to replace the power supply with a power supply of labour "Known", to see if that makes a difference.

  This system does not use an exclusive power of Dell, you can install most power supply ATX with a power connector 24 pin or 20 + 4 pin main motherboard and this can be purchased in most local computer stores, or online.

  The 9200 has a rear panel open, a diet with or without the on/off switch can be installed.

  Note: You need a PSU with six SATA power connectors.

  Otherwise, you can buy a refurbished Dell OEM [Dell P/N KH624] 375w PSU from here:

  http://www.Amazon.com/Dell-dimension-power-supply-KH624/DP/B0039OHV2O

  Bev.

• El Capitan upgrade must be done with a clean install?

  Hello

  El Capitan upgrade should be done with a clean installation, as opposed to an upgrade?

  I don't know how to do this, or what are the advantages and disadvantages?

  This means all the software on my computer is deleted and I need to re - install all the applications (if installing a clean)?   I think not so thought I had better ask!

  Best regards

  Mike

  If you have existing question in your system current, then things could get worse if you upgrade simply. My personal choice is always do a clean install of newest version of Mac OS X.

  How to perform a clean install of OS X El Capitan on your Mac.

  How to prepare your Mac OS X 10.11 "El Capitan."

  OS X El Capitan-download and Quick Installation Guide

  Make your own installer from El Capitan flash drive using the El Capitan tool:

  Be sure to save the installer in the downloads before installation folder, otherwise it will be deleted once the installation is complete.

  You can create an installer of flash of El Capitan via the Terminal drive. El Capitan has its own manufacturer Installer integrated that you use via the Terminal:

  You'll need a freshly partitioned and formatted at least 8GBs. USB flash drive leave the name of the flash drive on the system by default, "Untitled." Do not change this name. Wait as the full process that will take some time.

  Open the Terminal in the Utilities folder. Copy and paste the following line in its entirety in the Terminal window.

  sudo/Applications/Install\ OS\ El\ Capitan.app/Contents/Resources/createinstallmedia--volume/Volumes/Untitled--applicationpath X\ "/ Applications/install OS X El Capitan.app.

  Press RETURN, enter the admin password (will not resonate to the window) then press RETURN again.

  You must have setup in your Applications folder or change the paths in the command line above.

• I bought Photoshop elements 13 5 months ago and it was working fine until yesterday... Now, it will not open for me. I get a message to open it in the application - but when I tried it, it still does not open

  Hello

  Can you please try the steps mentioned at https://helpx.adobe.com/photoshop-elements/kb/editor-does-not-start-error-mac-app-store.ht ml

• WiFi stop working when 9.2.1 upgrade... A does restore the network configuration and still does not!

  from one day to the next my phone is suddenly being updated to 9.2.1. Since then my wifi was NOT working period. Have excellent wifi signal and still absolutely nothing. I reset the network settings and nothing works. Never been a problem until this 9.2.1 update

  I have the same problem after updating ios 9.2.1

• Upgrading a macbook air 10.6.8 to 10.11 and got this msg: Word, excel, and entourage will not work.  they run on my iMac 10.11

  Why my macbook air support the word and Excel at 10.11.  On my iMac, they run fine under 10.11.3.

  You can go to the Microsoft website and check with their support team.

• As a web designer, I've used menus xara on a number of sites and they looked fine until this that Firefox 7; now the menus have shifted to the left. Can you tell me a workaround solution? The menus are very well in other browsers. THX.

  Some of these sites have used xara menus (which are based on javascript) for years without problems. Because I used Firefox as my browser by default since its first release, so I would have recognized the problem immediately if it was before version 7. Also, I run Firefox on my iMac with Lion; I don't know if the problem of menu-shift is also seen on the Windows machine with the new version of the browser. Well, I hope you can tell me a quick solution I can install on the affected sites.

  But if you insist, try this version:

  http://jeffersonscher.com/forumshots/xaramenu_1.js

  I have not tried in older versions of Firefox.

• Upgrade RAM P105 satellite from 2 GB to 4 GB and it will not start

  I am trying to upgrade my P105 poles factory PC4300 original 2 from 1 GB to two sticks of 2 GB PNY PC5300.
  The new DDR2 667 Mhz ram according to the web site of Toshiba, however, with the two sticks of the new ram in place (4 GB), my computer does not start.

  With the new ram in place (2 GB) stick, my computer starts very well.
  With two sticks of the original ram (2X1GB) implemented my computer starts very well.
  What gives? Anyone know?

  I read that this laptop supports 4 GB of ram, although only about 3 GB will be mapped for use and this is acceptable to me.
  With 4 GB of ram installed, the BIOS recognizes 640 ram Base and 3 GB of memory.
  Is it possible to get this computer with 2x2gb DDR2 PC5300 ram?

  I am currently running Windows XP Media Center Edition SP3.
  It'd be better if I installed one of the versions the PC 5300 2 GB sticks and one of the original PC 4300 sticks 1 GB?

  Tanks for all help.

  Hello

  In my opinion, the laptop does not start because of the compatibility issue.

  The laptop was equipped with modules PC4300.
  So why you n t using 2 x 2 GB PC4300 modules?
  PC4300 DDR2 533 Mhz modules should run ok.

  If you want to use a PC-5300 and a PC 4300 module, then both modules would go at the same speed as the slower module in your case 533 Mhz.

  This is why they do not since I use a PC5300 and a single PC4300.

  In addition, the module speed depends on the bus (FSB) front.
  If the front side bus support 533 Mhz max then your module would go max to 533 Mhz even if the modules would support higher speed.

• Is this a legitimate email from microsoft asking for all my personal info to upgrade their network. I got the days now.

  I received an email from hotmail.com to respond and update my personal information so that they can update their records as they have apparently lost some files.  Please let me know if this is legitimate or not...

  Very definitely not.