Palm pre 2 stuck on the hp logo

I had a problem with palm pre 2 (2.2.4). I use it in India. Now, he has been slain at the hp logo and I need a procedure to get rid of this feature of evil.

Here is a link to remove the battery from the series of pre phones.

http://KB.hpwebos.com/wps/portal/KB/na/pre/pre2/unlocked/solutions/article/44919_en.html

While you're there, it would benefit you to download and read the User Guide:

http://KB.hpwebos.com/wps/portal/KB/na/pre/pre2/unlocked/downloads/page_en.html

WyreNut

Tags: HP Tablets

Similar Questions

  • My iPhone 6 is stuck on the apple logo

    My iPhone 6 is stuck on the apple logo. If I put it to download it just stays like that or it stops and says it has no battery, even when plugged. I can't enter in recovery mode because my home button just stopped working out of the blue. I don't know what to do.

    Charge the battery for an hour and then try the recovery mode.

  • Stuck at the apple logo & no backup to restore

    Well, I have an iPhone with ios 9.3.3 6. When I turn on my phone it stuck at the apple logo and after 10 seconds it turns off and when I turn it on again, same question.

    • Not having iTunes backup
    • No effect after hard reset
    • Tried to resolved via Recovery Mode, updated and restored but the problem is always there, always stuck and goes off

    Did you put your iPhone in DFU mode before resetting?

  • My iphone is stuck with the itunes logo

    my iphone is stuck with the itunes logo. How can I unlock it? »

    Your phone needs to be restored. Take a look at the instructions here.

    If you have forgotten the password for your iPhone, iPad or iPod touch, or your device is disabled - Apple supports

  • Stuck on the Apple Logo screen

    My phone froze so I restarted. It got stuck on the apple logo screen and I tried to restore it. When I have it plugged into my laptop it would not restore because my boot drive is full. I tried to remove as much as I could turn off my laptop and emptying the trash and nothing will work. Its been sitting stuck/frozen on the logo of apple for 4 hours now. How can I fix it?

    Only way runs a restore via iTunes by putting the iPhone in recovery mode

  • iMac 8.1 stuck on the apple logo

    Model: iMac8, 1

    2.66 GHz Intel Core 2 Duo

    At 2BG memory when the problem started

    Mountain Lion 10.8.5

    Is in trouble with occasional frosts. Would be closed and it should restart very well. About 2 weeks ago, the computer froze. I shut down the computer and restarted. The apple logo came with the spinning wheel, and then just the apple logo.

    I can start safe mode. Tried resetting the PRAM, reset of SCM. Tried to start with all peripherals except keyboard and mouse disconnected. Use the command R to start the computer and went into the disc utilities. Disc checked and it said disc looks OK. Verified permissions. Mistakes came for iTunes more a warning which was not repairable. Fixed permissions. None of these permits to start properly.

    Parle talked anyone computer repair who suggested to unplug the computer, hold the power button while up to one minute, plug the computer back in and pressing the Start button. It came in fine. A few days letter that the computer froze and I had to stop it. You press the Start button, got the spinning wheel, so only the apple logo and apple logo. Start the computer by pressing command + R and reinstalled Mountain Lion. Installation once it stuck at the apple logo again. Active disk. Drive seems to be OK. Permission verified. Permission with iTunes but issues no warning this time. Repaired permissions. Nada.

    Inserted the installation disk, turned on the computer while holding D key. A ran Apple Hardware tools (tests of short or long). This error message came up twice with different numbers of rpm: 4MOT/1/40000003: drive HARD-110. I know that it's the hard drive fan. Computer repair man came out. Thought problem may be because I only had 2 GB of memory and ran only to open the Lion of mountain with several programs. Upgrade to 4 GB memory, which is recognized by the computer. But the computer still does not start correctly. Tried the Single Mode and run/sbin/fsck - fy. Said it seemed OK, but changed the volume. Ran he says once again and everything seemed OK. Still will not start.

    When I start in the disc, part of the grey background Utilities is missing. If you move the cursor on the screen, the gray background fills.

    Also, when I try from normally I get startup chime, the apple logo and the spinning wheel. After that make a spin the wheel stops, there is sort of a Flash, then the wheel goes and remains the apple logo. I can hear the computer tries to do something, then the arrow cursor appears and can be moved around the screen. It's like that.

    Also installed Mountain Lion on a USB key, it made the startup disk and tried to start the computer normally. Still will not start.

    Any ideas or suggestions for what could be wrong or other things to try?

    1. the present proceedings is a diagnostic test. It doesn't change anything for the better or worse and therefore, by itself, will not solve the problem. But with the help of the results of the tests, the solution may take a few minutes, instead of hours or days.

    The test works on OS X 10.8 ("Mountain Lion") and later versions. I do not recommend running it on older versions of Mac OS X. It will do no harm, but it will not do not much good.

    Do not be put off by the complexity of these instructions. The process is much less complicated than the description. You make the tasks more complicated with the computer all the time.

    2. If you do not already have a current backup, please back up all the data before doing anything else. The backup is needed on the general principle, not because of what anyone in the test procedure. Backup is always a must, and when you encounter any kind of problems with the computer, you can be more than the usual loss of data, if you follow these instructions or risk not.

    There are ways to back up a computer that is not fully functional. Ask if you need advice.

    3 here is instructions to run a UNIX shell script, a type of program. As I wrote above, it doesn't change anything. It does not send or receive data over the network. There is no to generate a report on the State of the computer human readable. This report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents for me or someone else.

    You should ask yourself if you can believe me, and if it is safe to run a program at the request of a foreign national. In general, no, he's not sure, and I encourage it.

    In this case, however, there are ways for you to decide if the program is safe without having to trust me. First of all, you can read it. Unlike an application that download you and click to start, it is transparent, anyone familiar with the code can check what it does.

    You may not be able to understand the script yourself. But variations of it have been posted on this site several times over a period of years. One of the million registered users to have read the script and set off the alarm if it was dangerous. Then I wouldn't be here now, and you would not be reading this message. See, e.g., this discussion.

    However, if you cannot satisfy yourself that these instructions are safe, do not follow them. Ask other solutions.

    4. here is a general summary of what you need to do, if you decide to go forward:

    ☞ Copy text from a particular web page (not this one) to the Clipboard.

    ☞ Paste into the window to another application.

    ☞ Wait for the test to run. It usually takes a few minutes.

    ☞ Stick the results, which will be copied automatically, in a response on this page.

    These are not specific instructions; just a glimpse. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait and paste it again. You don't need to copy a second time.

    5. try to test in conditions that replicate the problem, to the extent possible. For example, if the computer is slow intermittently, run the test during a downturn.

    You may have started up in safe mode. If the system is now in safe mode and works pretty well in normal mode to test run, restart as usual before running it. If you can test only in safe mode, this.

    6. If you have more than one user and a user is affected by the problem, and the user is not an administrator, and then run the test twice: once under the affected user and one administrator. The results can be different. The user that is created automatically on a new computer, when you start it for the first time is an administrator. If you are unable to log in as an administrator, verify that the user concerned. More personal Mac have only one user, and in this case this section does not apply. Don't log in as root.

    7 load the linked web page (the site "Pastebin.") Press the combination of keys command + A to select all the text, then copy it to the Clipboard by pressing command-C.

    8. start the Terminal application integrated in one of the following ways:

    ☞ Enter the first letters of his name ("Terminal") in a Spotlight search. Select from the results (it should be at the top).

    ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

    ☞ Open LaunchPad and start typing the name.

    Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing Command + V, then press return. The text that you pasted should disappear immediately.

    9. If you logged in as an administrator, you will be prompted for your login password. Nothing displayed when you type. You won't see the usual points instead of the characters typed. Make sure that caps lock is turned off. Type carefully, and then press return. You can get a warning to be careful. If you make three unsuccessful attempts to enter the password, the test is still running, but it will produce less information. If you do not know the password, or if you prefer not to enter, just press back three times at the password prompt. Yet once again, the script will run.

    If the test takes much longer that usual to run because the computer is very slow, you can be prompted for your password a second time. The permission you grant by entering it will expire automatically after five minutes.

    If you are not logged as an administrator, you will be prompted for a password. The test will run. It just will not do anything that requires administrator privileges.

    10. the test may take a few minutes to run, depending on the number of files you have and the speed of the computer. A computer that is abnormally slow may take more time to run the test. During execution, a series of lines is displayed in the Terminal window like this:

        Test started
            Part 1 of 4 done at: … sec        …        Part 4 of 4 done at: … sec
        The test results are on the Clipboard.
        Please close this window.

    The intervals between the parties will not be exactly the same, but they give an approximate indication of progress.

    Wait for the final message "Please close this window" appear - again, usually within a few minutes. If you don't see this message in about 30 minutes, the test probably won't be completed within a reasonable time. In this case, press the Ctrl + C key combination or the point command to stop it. Then go to the next step. You will have incomplete results, but still something.

    In order to get results, the test should be allowed to perform or be stopped manually as shown above. If you close the window of the Terminal, while the test is still running, the partial results will not be saved.

    11. when the test is completed, or if you manually stopped, leaving the Terminal. The results have been saved to the Clipboard automatically. They do not appear in the Terminal window. Please do not copy from there. All you have to do is start a response to this comment and then paste it again by pressing Command-V.

    At the top of the results, there will be a line that begins with the words «Start time.» If you do not see that, but rather to see a mass of gibberish, you wait for the message "close this window". Please wait and try again.

    If personal information, such as your name or e-mail address, appear in the results, make anonymous before posting. Usually it will be not necessary.

    12. in the validation of the results, you see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the software which manages this website. Thanks for posting the results of the tests on Pastebin, then post here a link to the page you created.

    If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

    13. When you are finished with the test, it is gone. There is nothing to uninstall or clean.

    14. This is a public forum and others can give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but all that you can not be. For others who choose to run it, I do not recommend that you view the results of test on this Web site unless I ask.

    15. the related UNIX shell script is a notice of copyright. ASC readers can copy for their personal use. The whole nor any part can be redistributed.

  • iPad stuck on the apple logo

    IPad is stuck on the Apple logo and halfway along the slide to download

    was reset as the wifi would not connect

    This can help:

    Press and hold the power button / stop and the Home button at the same time, the corners of the black screen,... .in taking... When you see the white apple logo appear to leave bot buttons go.

  • Pavilion G6: upgrade Windows 10 has not stuck on the HP logo

    Tried to update 8 victory to win 10. Stuck on the HP logo.  I tried to unplug and and reinstalling the battery (let stand a little and pressed the power button to drain the energy). I tried failed bios, tried to turn on virtualization, all tried restore, startup repair the computer after trying to start several times, restore points are gone, I don't have a CD because HP no longer send them. I don't know what to do with this thing. Help, please.

    fixitrod

    Hello;

    Let me welcome you on the HP forums!

    While Microsoft says there is no risk in the upgrade of Win10, because they allow you to believe that you can always return to your BONES and the original installation program within 30 days, the ugly fact of the matter is that the Win10 GoBack feature turned out to be unreliable - and when she fails, she can let machines in a State corrupted - that does not always happen , but it happens often enough to be a problem and you will get no warning beforehand that he goes to the trash your PC!

    If this is not enough, the Win10 upgrade is known, in some cases, corrupt partition recovery stored by the OEM that built the original machine. It's pretty much guarantee that no HP recovery will work.

    What will work restores your computer to its original factory state using HP recovery media.

    It is a set of DVD and a CD or a USB key, which will erase the hard drive (removing all data, applications and settings, reinstall the original OS, drivers and utilities for HP. In some cases, you will be able to order a USB instead of discs.  You must order at HP; they cannot be downloaded.

    You can look online for recovery from the paged media related: http://support.hp.com/us-en/drivers

    Once there, enter your product name or number. On your software page and download the drivers, select your operating system and version. Click on "Update".  If the HP recovery support is available for your computer, down near the bottom of the page, you will see an entry for the command Recovery Media-CD/DVD/USB. Click on the symbol '+' to expand this entry and click on order to press for more details.

    Or, if you prefer, you can do the same by contacting HP Customer Service:

    If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1

    If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html

    NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!

    If HP no longer provides a recovery media for your model, a few other sites, you can check are: http://www.computersurgeons.com/ and http://www.restoredisks.com/

    Good luck

  • Pavilion x 360: tour of laptop computer during the upgrade to Windows 10 stuck on the hp logo

    I was upgrading the laptop for Windows 10 and after that it restarted, it got stuck on the logo of hp for about 30 min. I turned it off about 3 times and it is still stuck on the hp logo.

    Once the recovery to Win 8 is completed, considering the upgrade to 10, here are some tips:

    > http://support.hp.com/us-en/document/c05195282

    > http://support.hp.com/us-en/document/c04730900

    Make sure all your drivers are updated before moving to 10 - use HP Support Assistant

    Make sure you that all of your software security (AV, firewall, etc.) is uninstalled before upgrading - reinstall the upgrade of the post.

    If you decide to not upgrade, please note that Win 8/8.1 is good OS and will be supported by Microsoft until the year 2023.

  • [NEED HELP] Acer B1-730HD stuck on the USB logo

    After update my Acer B1-730HD kitkat... The problem seen is dat what acer B1-730HD stuck on the USB logo. I'm looking for solution on google for a few days to view, not yet found how flashing a rom for Acer B1-730HD. I am very disappointed with your service as acer do not DOWNLOAD on the Web site's original rom. Now, I need original rom for Acer B1-730HD, please!

    Sorry to hear that you have this problem after the update of your tablet.

    You try to run a factory data reset.

    1. Turning off the tablet.
    2. Press and hold the Volume up button, which is located closer to the touch screen lock switch.
    3. With the Volume up button which is held, press in and hold the Power button for 3 seconds, then release it. Continue to hold the Volume up button.
    4. Once the tablet screen lights up, release the Volume up button.
    5. In the select the Boot Mode screen, select [SD picture Mode of update]. Use the Volume and Volume keys to navigate through menus and use the power button to select the desired option.
    6. On the Android system recovery screen, select wipe data / factory reset.
    7. When you are prompted to confirm deletion of all user data, select Yes - delete all user data.
    8. On the Android system recovery screen, select reboot system now. Your data will be erased.
    9. Your tablet will restart and go to the Welcome screen. Follow the steps on the screen to configure your tablet.
  • Start stuck at the Dell logo screen

    Hello

    I have an inspiron nine 5447, which was working fine until yesterday. If I try to start now, it's just stuck to the Dell logo and I can't go in the BIOS settings. I tried pressing F2 and F12, but the screen is still stuck at the same screen of the Dell logo. Can someone help me with this.

    Thank you

    Nikhil

    Hi Nikhil,

    External devices (except AC adapter) connected to the computer. If so, disconnected the and try to turn on the computer.

    If it's the same situation, and then turn the computer off. Key down, then and now the power of FN key on the computer.

    In the case, the computer is blocked at the Dell logo. It's a hardware problem, contact Dell Technical Support in your region to replace the parts.

    I hope this helps...

  • IPod 160 GB Classic is stuck on the apple logo. I have reset several times and I can not put in DFU mode or resets it to take. Done all the help topics that I have seen here and nada... Please help

    help me get the apple logo take off. I reset it, tried and failed to reset. I can't put it in dfu mode. I'm stuck and need help pease. I did everything that was mentioned in other posts similar to this issue.

    That may mean the iPod has a hardware problem, such as a faulty hard drive or the logic board.

    When you do a Reset (press and hold the Menu and Center buttons), going blank at the start before the Apple logo returns the screen to the iPod?  Or do you mean that the Apple logo is 'stuck' and it doesn't go away when you try of the reset?

    Is the "DFU mode" procedure for disc Mode.  Have a look here to confirm that this is what you have tried

    How to put your iPod in disc - Apple Support mode

  • PHONE STUCK IN THE APPLE LOGO!

    So my phone was working and I took it, started to use it and then the screen went black and the apple logo appeared and its been stuck with her since... what I have to do this take off?

    This article offers possible solutions.

    https://support.Apple.com/en-us/HT201412

  • Why my iphone 6 more stuck with the apple logo and the black screen after the factory reset?

    I'm selling my iphone 6 Plus I did a factory reset, but it has stuck on a black screen with the white apple journal for more than an hour, why what is happening?

    Force the restart: press the lock and home buttons until the Apple logo appears again.

  • Equium p200 1IR - stuck on the Microsoft logo

    My laptop seems to be "stuck" on the logo of Miscosoft when initially loggin. It moves on the screen Toshiba showing options that lets you choose PF2 or PF12 to implement menus etc. It was left during the night and always do the same thing, trying to start upward, but without success.

    Hello

    I put t know why this happens but can access the advanced boot menu by pressing F8? It can choose the safe mode option and try to start in this mode.

    If it doesn t work I think you should try to reinstall Windows using the Toshiba recovery disc.

    Moreover, a HARD drive is recognized in the BIOS correctly?

Maybe you are looking for