PALM TX - Factory Reset question - need help

Similar Questions

• C20 TC5.0 FACTORY RESET QUESTION

  Need help please.

  I have a C20 of the TC5.0 running software.

  Using the document quick set c20 for factory reset... I turned off the system.  Just press on and hold power and get the flashing of the LED (GRN).

  Problem is that when I press and hold button LED GRN light never comes to the top.  After about 8 to 10 seconds, I have the RED Led.  When I release the button of the normal commenses system starts.  ?????

  All the ideas that I need to get the password reset on the thing.

  E-mail: [email protected] / * /

  VR

  Chet

  The factory reset procedure was changed in software version TC5.1, so anything before that has a different procedure than newer versions.

  As has been mentioned by Jens - factory reset procedure is different on the version of the software you are using, so, in your case, with the TC5.0 software, you will need to use the "old way".

  There are a description of the methods in the jrandby post in the thread c20-factory - default - power button .

  As mentioned in the Troubleshooting Guide (pages 22-25), the physical method of performing a factory reset is one of the last options resort - there are other methods, first of all, you should try.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• T510 factory reset question

  Windows 7 64 bit on my T510 is dead. When you connect, it hangs on the forever login screen. Windows Recovery failed too. It lasted eight hours and reported an error (something like error to restore a file and the disk is full, although my C drive is half empty). After that, all the Windows restore points have disappeared. So I guess I need to factory reset.

  My question is, I made two other partitions on my hard drive using external tools, that store all my data. So when I do the factory reset, these two partitions are replaced? Any suggestions so I can recover the system while keeping all my data? Thank you.

  The resumption of the plant will remove all partitions on the disk. Faced with a similar problem, here is what I do:
  First of all, I have remove all hard drive passwords. Then, I suggest Vibrio hard drive test in BIOS to see if the drive is the root of the problem. Buy a new hard drive, then install the OS on the new drive. The old disk can be mounted in a USB enclosure or an Ultrabay adapter to access the data. I tend to keep the old drive for 3-6 months in case I've missed or forgotten something, so I sell or reuse the old disk, after the failure of it.

• HP Pavillion DV6 - full reset and need help

  Hello, I need help with my HP Pavilion DV6 laptop. Recently, a virus was on the computer and I did the scan and difficulty. the computer was running a bit slow so I backed up the computer to my external hard drive. I tried to retrieve the disks of the computer but it kept failing. I did on the last attempt to put them on dvd, but when I reset my computer he remained in d; Recovery. I tried several things to get out of recovery. I tried recoveering for the final analysis known and save. I have tried the factory reset, and nothing has worked. I've done all the analysis possible on the computer. I had a disc of windows just to see if I could come back in windows and it loads fine, but now there is the problem. my computer is not the case, as it should be. My wifi is not available, and the implementation is somewhat different. Is there a way I can return my computer to facotry settings? My brother and dad have the same exact computer I do not know if you use it recovery disk would restore my computer to its original settings or not. Any advice or assistance would be greatly appreciated.

  Hello

  In this case, as long as the laptop belonging to your Dad or your brother is exactly the same (that is to say the exact same model No., hardware and version of Windows 7), then their recovery media will work on your laptop.

  Kind regards

  DP - K

• Factory reset question

  I have reset to factory my AE this morning and he automatically joins the network. The next time I did it, the amber light remains flashing. I have to connect it via Ethernet for the initial Setup? Thank you for your help.

  Cheers, Peter

  I have reset to factory my AE this morning and he automatically joins the network.

  She could not do this if the reset was a success, given that the network settings on the Express would have been totally erased in a successful reset.

  Next time that I did, the amber light is still flashing

  This indicates that the reset was successful.

  I have to connect it via Ethernet for the initial Setup?

  Use an Ethernet cable during installation only if you plan to have the Express connected permanently to your router using a wired Ethernet connection.

  Use wireless during installation of the Express, if you plan to have the Express connect wireless to your existing wireless network.

  In other words, you set up the Express the way it will be used with your network.

• Re: Satellite T130 - 11H - Factory Reset questions

  Hello

  I had to reset my Satellite T130 - 11 H to factory settings to try to stop the issues with my internet and computer in very slow summer and unresponsive, but now when it starts it states that it is "complete the installation may take several minutes" then restarts on its own starts again, then restart again and again!

  Now it is tell ing, the same message but just hangs and does not go on my counter top?

  Help

  Thank you

  Hello

  I know during a recovery procedure you laptop will restart several times. So, don't interrupt and wait. If it restarts always for a long time, you can restore the settings to factory using recovery media, you did

• Force10 S60 Factory Reset question

  Hi all

  As the title says, I have a S60 Force10 that I need to restore factory settings, but none to the documentation I found so far has worked.  When I tension, rather than get the menu "Select an option" normal, it messages "submarine 1.3.4" and run the boot sequence instead.  At a time given in the process, it gives me the ability to stop Auto-start sequence, but not the choice if I do.  Call the help file to the moment there does not offer much either...

  I know, it cannot be that hard, so I must be missing something simple.  Someone at - it was otherwise here?  I don't need to keep all the settings, I want to just configure the switch from scratch.

  Thanks in advance,

  -Michael

  After entering the commands

  -Online setenv stconfigignore true

  -Online saveenv

  Allow the system to boot completely, without pressing any key during the boot process. Don't worry not about entering default settings restore. Once it is done booting, what status is the switch then in? It is operational and accepting orders? Or another status?

• BlackBerry Smartphones strange question need help ASAP!

  I have a strange problem with my Blackberry "BOLD" 4 9900, sometimes when I receive or make a call, the phone is connected and I don't get 2 hear the person at the other end, and vice versa, the only solution for this is hard reboot the phone that is like taking the battery and have it pop back in and then things works very well and it's soething that happens daily is there a way to diferrent without restarting the phone and why it happens instead of 1 m, also I got the replacement of the device like the previous, it was cut and after investigation of blackberry, they gave me a new device. The version of the OS in the mine is 7.1.0.746 (2108), I was invited by the service 7.1 bundle downgrade and backup center 1646, which I am not ready to do what it takes forever and I have to reinstall all the software back and set up e-mail. What would you suggest?

  Also the latest BBM version which is 7.0.1.23 is installed, my phone that has WiFi but unlike previous versions where they had a backup and restore under backup management option that is no longer there, there at - it a way to get that back, I had uninstalled and reinstalled BBM but still does not work and the desktop software is not save BBM groups or pins?

  Bold_4_9900 wrote:
  Well thank you for the steps of IMRT I'll take an impression outside until I do it just to be double sure and I installed restart me that works well but has 2 questions in my mind. Why my phone should behave mumb silent n when I get a phone call or have to do one and the is to run return is of restarting it.

  This happens usually when application runs in the background, or because of any unknown third-party application installed within our system, or due to lack of memory. Reboot to shoot some time A battery is enough to solve this problem. If press and hold the Menu for a few seconds, it will appear a screen that will display all the programs running in the background, usually five will always be there (host, BBM, Message, phone, browser) you can always check if any other applications. are running in the background, if they then close them properly.

  We should always try to close Applications correctly - avoid using key end to close the applications because it just minimizes the application and let it run in the background. Instead, press the Menu key, select close or Exit to exit the application. Do not leave your browser open on a page of Web active when not in use. If programs are running in the background, that this will lead to problems that you are experiencing now. Please take a look at this Article, I don't know that it will help you overcome your problems:

  KB14320 : How to maximize the battery life and available memory on the BlackBerry smartphone.

   

  Bold_4_9900 wrote:
  Also, you mentioned the OS upgrade to make the site of Vodafone UK as it approves Indian have not come out, I hope it's a generic file and has nothing to do with zonal or regional my phone settings.

  There is no generic OS! The link I gave you is an official OS from Vodafone UK, install it without any hesitation he will not affect your device 

  Let me know if you have any questions.

• BlackBerry Smartphones Newbie with 2 questions, need help.

  Hi guys,.

  hope you can help. I recently bought a BB Curve and think it's great.

  However the LED stopped working. I turned off the unit and removed the battery. When I put it in the LED lights up red, so it must work. I checked my profile settings and all say that the LED must be on. I have changed this setting to disabled, backed up, and then put it back on and saved and still no action led.

  The second question is attachments on my emails. I can't open attachments, photos, documents spreadsheets nothing. I use desktop re-Director. Is it possible to have attachments that are sent using this unit or any other bits of software? I have the only BB at work so I'm not so sure, establishment of a BB server is viable.

  Your opinion would be greatly appreciated.

  There is not all the configuration parameters for the Service of the attachment. The following table describes the supported types of attachments on a BlackBerry

  http://www.BlackBerry.com/BTSC/KB03265

  By default the LED flashes green to indicate that you are in a wireless coverage area. I found it annoying and disabled. Check the setting under Options | Screen/keyboard and turn the LED coverage indicator inactive.

• My Palm Zire m150. I need HELP!

  OK lol so I was looking through my drawer and I came to find a brick, but not no matter what brick my palm pilot! I was like haha wow. I loaded and everything and it works again. but now I want help on where to find games to put on. I do not want the palm site because those who are there already. But if anyone has a good working link can they please hook me up. Thank you.

  Oh, and don't bother the Palm m130, they had no m150 lol

  Use any search engine... Enter 'Palm games' will provide thousands of visits!

  www.FreewarePalm.com is an example of what you can find.

  WyreNut

  Message relates to: Centro (AT & T)

• eCommerce Product Import question - need HELP!

  I'm trying to import 899 products in the e-commerce module, but it takes 6 + hours and I never get an end message.  Import shows that progress and products receive they added/updated but it takes a long time and I never get an end message.  Any ideas on why this is happening and how to speed it up?

  Hello

  Try to split the import in 400 points or less to see if that helps to improve your experience.

  If still in trouble I suggest you submit a ticket (join the import in question file) us as soon as POSSIBLE because it should take less than a minute by import.

  - http://helpx.adobe.com/business-catalyst.html (BC Contact Support)

  Kind regards

  -Sidney

• two questions, need help please

  Hi all

  the first question is, if I have a server with 16 heart and I have created 8 guests each has 4 cores (totally 32 cores), it will work? How?

  second question is if we talk about compatibility (if server or workstation) do we mean the CPU compatibility or the whole machine!

  Thank you, l

  In most cases, you will be able to install and run ESXi. However, he will not formally managed.

  André

• this.createEmptyMovieClip and load movie question need help

  Hi Folks, I'm building a site with a lot of mc at different depths and am using just code to load a picture from an external source without using_root of commands in one of the mc, it works fine when I test Flash, image loading well etc... but if I test it in a browser the image does not load. In fact if I just export the movie and play my desktop image does not load. It drives me crazy and I spent hours trying to solve this problem with no joy. The one you have ideas? This is the code (its just on an empty frame in my mc). Thanks, Craig

  
  

  var mc:MovieClip = this.createEmptyMovieClip ("mc", this.getNextHighestDepth ());

  mc.onRelease = function (): Void {}

  trace (this.image._url); / / http://sphotos-a.XX.fbcdn.NET/HPhoto...76612800_n.jpg

  }

  var image: MovieClip = mc.createEmptyMovieClip ("image", mc.getNextHighestDepth ());

  image.loadMovie ("http://sphotos-a.xx.fbcdn.net/hphotos-snc7/s720x720/318391_177260932418441_1276612800_n.jp g" "");

  You probably have a problem of cross-domain security.

  to remedy this, add your flash files/folder to your trusted list: http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager04.htm l

  Alternatively, upload to a server files and test.

• CMYK export questions - need help Urgent

  Hello

  
  

  I'm relatively new to printing processes and did my first book ready for printing. I tried to export my indesign files as CMYK, however the black txt that I placed on a JPEG photograph (used to fill the entire page as covers the front and back) seems very gray and not as vibrant.

  
  

  I realize that this is what happens when you export RGB-> CMYK, but the black txt has lost almost all of its power, while white txt offers no problem what so ever.

  
  

  This is why the cover loses almost all effects. the text in all the pages (because it is a publication intended for short stories / poetry) also loses impact and dynamism, so the photographs appear to be well.
  

  
  

  What happened in the past where I used a transparent .gif or .png and pasted into the document.

  
  

  Please help with this, I know I probably got a wrong setting somewhere I export to Document CMYK - us Web Coated (SWOP) 2.0.

  
  

  Here, very confused! can provide screenshots/more information if necessary for the help I'm losing my mind on this one.

  
  

  Thank you very much to all those who are ready to help!

  
  

  Owen

  It's Black display and export, fusion of transparencies space preferences (this is for printing, set it to CMYK) and your Swatch used for blacks. I have my set of values by default and don't ever deviate and know not how no goof it upward. Look at my screenshot, the samples and the results.

  

• ACS 4.2 install question - need help

  Hello

  Once installed the 4.2 of the ACS, the ACS HTML interface leave empty when accessd locally using the icon from the desktop or by typing http://127.0.01:2002, so I'm not able to configure the user name and password.

  When I accessd GBA from another host by: http:// 10.1.115.222:2002 (the 10.1.115.222 is the ACS server address), the prompt "username" and "password" appeared. But not able to loggin as I don't have username and password configured.

  When I tried to access locally by: http://10.1.115.222:2002, IE still leave empty.

  Note: OS: Server 2003 in vmware esx, IE 8.0, Java,.

  Thanks in advance!

  Please go to ACS--> Admin---> political Session control and uncheck--> allow local access auto connection

  Now try to connect.

  Kind regards

  ~ JG

  Note the useful messages