Pass a license Base of LAN IP based on a battery of WS-C3750X-48P-L

Hello

I have two switches WS-C3750X-48P-L with LAN licenses stacked. I want to upgrade the license on each of the LAN Base to Base of IP.

Me am .lic files from Cisco partner and stored in flash:

Flash #dir shan2021:
Directory of flash: /.

442 - rwx 13260 April 1, 2011 13:48:20 + 02:00 config.text
443 - rwx 1936 1 March 1993 02:53:30 + 01:00 vlan.dat
444 - rwx 1152 1 March 1993 03:01:55 + 01:00 FD01503Z1C5_20110330204317053.lic
445 - rwx 1152 1 March 1993 03:08:14 + 01:00 FD01503R0WU_20110330204634394.lic
447 - rwx 1909 1st April 2011 13:48:20 + 02:00 private - config.text
drwx 2 512 1 March 1993 01:16:57 + 01:00 c3750e-universalk9 - mz.122 - 53.SE2
448 - rwx 3096 1 April 2011 13:48:20 + 02:00 multiple-fs

total 57671680 bytes (40040448 bytes free)
shan2021 #.

Tried to upgrade with orders

shan2021 #license install flash: FD01503Z1C5_20110330204317053.lic
Installation of licenses from "flash: FD01503Z1C5_20110330204317053.lic.
% Error: installation failed. UDI WS - C3750X - 48 P - L:FD01503Z1C5 on the license does not correspond to any device
0/1 licenses have been installed correctly
0/1 licenses were existing licenses
1/1 licences have been impossible to install

shan2021 #.

shan2021 #license install flash: FD01503R0WU_20110330204634394.lic
Installation of licenses from "flash: FD01503R0WU_20110330204634394.lic.
% Error: installation failed. UDI WS - C3750X - 48 P - L:FD01503R0WU on the license does not correspond to any device
0/1 licenses have been installed correctly
0/1 licenses were existing licenses
1/1 licences have been impossible to install

shan2021 #.

But it does not work. The IDUs seems to be correct:

shan2021 #sho license udi
SN UDI device # PID
-----------------------------------------------------------------------------
* 1 FDO1503Z1C5 WS-C3750X-48P-L WS-C3750X-48 P - L:FDO1503Z1C5
2 FDO1503R0WU WS-C3750X-48P-L WS-C3750X-48 P - L:FDO1503R0WU

shan2021 #.

Guessed that maybe because they are stacked the process does not work, so was by restarting the other and tried to update the license on the first during the restart of the second, but it doesn't work anymore.

I did not have physiqueet access to the switches, so can not try to remove the battery cables.

Nobody knows, including at - it a special order to upgrade the license in which case the basis of LAN 3750 X switches are stacked?

I know that the upgrade on a standalone switch works fine, I tried on another.

According to me, the .lic files are okay, looked at them and they seem to be wrong.

Here's the full sho VER

shan2021 #sho worm
Cisco IOS software, software of C3750E (C3750E-UNIVERSALK9-M), Version 12.2 (53) SE2, VERSION of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Updated Thursday, April 21, 10 05:11 by prod_rel_team
Image text-base: 0 x 00003000, database: 0 x 02400000

ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M), Version 12.2 (53r) SE1, RELEASE SOFTWARE (fc1)

shan2021 running time is 3 hours, 53 minutes
System to regain the power ROM
System restarted at 10:51:37 CEST Friday, April 1, 2011
System image file is "flash:/c3750e-universalk9-mz.122-53.SE2/c3750e-universalk9-mz.122-53.SE2.bin".

This product contains cryptographic features and is under the United States
States and local laws governing the import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third party approval to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. laws and local countries. By using this product you
agree to comply with the regulations and laws in force. If you are unable
to satisfy the United States and local laws, return the product.

A summary of U.S. laws governing Cisco cryptographic products to:
http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html you need assistance, please contact us by mail at
[email protected] / * / Level: lanbase
License type: Permanent
Then reload license level: lanbase

If

License

WS-C3750X processor - 48P (PowerPC405) Cisco (revision A0) with 262144 K bytes of memory.
Card processor ID FDO1503Z1C5
Last reset of tension
2 virtual Ethernet interfaces
1 interface FastEthernet
104 gigabit Ethernet interfaces
4 ten interfaces Ethernet Gigabit
Password recovery mechanism is activated.

512K bytes of memory simulated by flash not volatile configuration.
Basic Ethernet MAC address: C8:9 C: C of C to D: 5 1:7:00
Motherboard set number: 12553-73-04
Motherboard serial number: FDO15040UGP
Revision number of the model: A0
Motherboard revision number: A0
Model number: WS-C3750X-48P-L
Daughter numbered card: 800-32727-01
Daughterboard serial number: FDO15040SQM
System serial number: FDO1503Z1C5
Top Assembly part number: 800-31324-01
Top of page revision number of the Assembly: A0
Version ID: V01
CLEI Code number: COMJZ00ARA
Revision number of hardware consulting: 0x02

SW Version SW Image model switch ports
------ ----- -----              ----------            ----------
* 1 WS-C3750X - 48 54P 12.2 SE2 (53) C3750E-UNIVERSALK9-M
2 54 WS-C3750X - 48P 12.2 SE2 (53) C3750E-UNIVERSALK9-M

Switch 02
---------
Switch Uptime: 1 hour, 1 minute
Basic Ethernet MAC address: C8:9 C: D: 3 1: 39:80
Motherboard set number: 12553-73-04
Motherboard serial number: FDO15032371
Revision number of the model: A0
Motherboard revision number: A0
Model number: WS-C3750X-48P-L
Daughter numbered card: 800-32727-01
Daughterboard serial number: FDO1503153L
System serial number: FDO1503R0WU
Top of page Assembly part number: 800-31324-01
Top of page revision number of the Assembly: A0
Version ID: V01
CLEI Code number: COMJZ00ARA
License level: lanbase
License type: Permanent
Next time you restart level license: lanbase

Configuration register is 0xF

shan2021 #.

shan2021 license #sho all the
License store: storage of main license
J:: function 0: lanbase Version: 1.0
License type: Permanent
The license status: Active, in use
License priority: medium
Number of licenses: not counted

License store: Evaluation License storage
J:: function 0: ipservices Version: 1.0
License type: assessment
The license status: active, don't use, not accept EULA
The total period of assessment: 8 weeks 4 days
Assessment period left: 8 weeks 4 days
Priority of license: no
Number of licenses: not counted

shan2021 #.

Need IP Base to add no-3750 X switch and also because of the power of the battery.

Assume that perhaps there is a specific license to add to a stack, something like command

switch to flash: FD01503Z1C5_20110330204317053.lic install 1 license
but have not found such a.

Thank you much for the help.

Vlad


Hi Vlad,

Make sure that the correct UID of each device, including upper and lower case letters are used to generate the license key, otherwise it won't work.

Alternatively, you can generate yourself the keys by clicking on this link and loogin with your CCO account

https://Tools.Cisco.com/swift/licensing/RegistrationServlet

HTH

Reza

Tags: Cisco Network

Similar Questions

  • Oracle Enterprise Edition licenses - base metric

    Oracle: 10G (10.2.0.4) 64 - bit Enterprise Edition
    Running on Intel Xeon chips, which, in my view, have a coefficient of multiple base of 0.5

    We have 540 licenses NUP on our site. We obviously have a direct box, and a few test boxes.

    One of our test boxes have 4 cores (Intel Xeon chip). Using minimum for Enterprise Edition licenses, after applying the base of 0.5 factor there would be 2 hearts, I believe that we need to 25 licenses NUP by heart, which would be = 50 NUP minimum for this test area.

    Is this right?

    My concern is that there may be a minimum of 4 cores (after factor) for Enterprise Edition. I can't find anything that confirms this. I can only find maximum rates for Standard, nothing for Enterprise Edition edition.

    If there is a minimum of 4 cores, so I need to get one of these test boxes.

    Everyone knows the facts on this?

    Thank you very much.

    Again, as everyone said above, you should contact Oracle Sales Rep.

    But still, let me answer your question, it is noted as minimum of 4 cores for enterprise edition. You can have license NUP even on 1 CPU.

    Another thing that might be beneficial, Oraclel gives you enterprise of limited use license to your Test/Dev box which means that you need only minimum NUP 10 s for Test/Dev business instead of the minimum of 25. This will save you 15 NUP by processor. But to do this, you must talk to Oracle or any third party provider.

    But even once best bet is o talk to Sales Rep.

  • Can you pass a license mobile phone to laptop?

    I bought a new laptop. I am being tested, don't know if I'll keep. I buy a new items 10. I intend to install it on this new laptop. What happens if I decide to return this laptop to the store, I have all my software will uninstall eventually. Will I always have 2 licenses left?

    Yes, just be sure to go to the Publisher > help > deactivate before uninstalling.

  • I can't open windows update in Safe Mode. Also blue screen at startup ('a forward driver a buffer based on the battery'

    My laptop keeps hitting a blue screen at startup ('a forward driver a buffer based on the stack'), I can only start it in safe mode. I want to try windows updates to see if this will help, but whenever I click on the button to update windows on the start menu, nothing happens. I tried searching for the program to see if I can open it another way, but can't find it. If I click on windows update and then nothing happened. I have windows vista home.

    original title: I can't open windows update

    Hey ElizabethSlater,

    Try to run a full scan with the Microsoft Safety Scanner to make sure that nothing is found.

    Try also to install the latest drivers from your computer manufacturer's website. If you have difficulty to locate the website of your computer manufacturer or the drivers on their page, please provide your computer brand and model in your next reply. If you have built your computer you need visit the site of the manufacturer of each piece of hardware to get the latest driver.

    Once the drivers have been installed, try to restart your computer, and then test to see if the same problem occurs.

    Hope that helps.

  • HP ENVY 17-j011sg Notebook PC: HP ENVY 17-j011sg based free spare battery parts

    Hello

    I'm very angry because I need to change the battery (security expited in January 2016) and in all the links of 1000 HP, I can't find the number. HP could make it more complicated, but there is no way.

    At the end of the spare parts site https://parts.hp.com/ there is no battery number to buy. I need to buy the keyboard too, because there is missing it B... and I can't find my product number.

    One could look at which is the number of spare parts to buy:

    Keyboard and batery:

    Modellnr. : E8P11EA

    Seriennr. : [Personal information]

    HP ENVY 17-j011sg notebook PC

    In the end, I have a very bad image of this structure (if I need to buy another laptop, you can be sure that I won't buy HP).

    Thank you

    (if someone can tell HP that is really not easy for the user, might be nice)

    Spare part number

    710417 001

    Description:

    6 cell, 62WHr 32.8AH Li - ion

    Please select 3 Illustrated catalogue of spare parts under the table of contents.

    http://h10032.www1.HP.com/CTG/manual/c03922401

    Hope this helps, for other queries in response to the post and feel free to join us again

    * Click on the white button on the right to say thank you Thumbs Up *.

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

    Thank you

    GBL84

    I'm not an employee of HP

  • How to pass the vcs - e License? A server to Server B.

    Hello

    my company has a vcs test server.  and we buy the new server.

    I need to spend vcs again server.   I backup and deploy using the vmware ovf file.

    deploy the success. but new server vcs poster license error.

    How to pass the license of vcs?

    Of his assignment, it is not necessary to use both servers at the same time.

    If I see, if you move the virtual computer between two servers and you used local storage the

    Serial number will change...

    Please remember useful frequency responses and identify useful or correct answers.

  • Low-pass filter before the NI 5112

    Hello

    I currently use a 5112 AND measure the signal of an infrared detector in an experience of ring to the bottom of the cavity. Below are three examples of signals. My main question is how I can implement a low pass filter, passive preference, before my 5112 OR undistorted extremely my signal due to the impedance mismatch. Now a few details:

    Some unique captures for each wavelength are shown in color, while average 25 pulses appears offset in black. The range and offset are chosen in each case in order to minimize the noise of "scanning". In the case of 3.14um, the noise that you see is about 25 times noise from scanning. They were taken without the limitation of BW and 100 ms/s mode.

    The detector (Vigo MIPDC-F-10) has a bandwidth of 10 MHz. I think it is a low impedance and is intended to be harnessed with 50Ohms, however its documentation confuses me, and I'm waiting for a definitive answer from the provider. 2.4 part of the manual says 50Ohms recommended, however the Datasheet and our map calibration (below) seem to suggest 1 MOhm is recommended!

    There are a few strange oscillations with a period of almost 180ns in our signal that I thought were due to the impedance mismatch existed in the system before I changed it:

    -Detector

    -1 metre 50 Ohm SMC Cable BNC (RG-174)

    -Inline BNC connector

    -meter 5, 75 Ohm BNC to BNC cable

    -Digitizer, DC, no BW limit, 100 ms/s, 1MOhm | 30pF

    When I saw this configuration, I knew something wasn't right and I even he modeled in LTSpice and he showed the same period of oscillations. But now, the Setup is:

    -Detector

    -1 metre 50 Ohm SMC Cable BNC (RG-174)

    -BW digitizer, DC, limit, 100 ms/s, 50 Ohm

    And we still have oscillations, even if the period seems to have changed to 320ns all about. These oscillations, which remain are 99%, probably due to our drop-down ring cavity experiment, however if anyone has recommendations on possible causes or ways I can confirm it is not because of my chain of detection they would be more than welcome!

    Now, the main question. Between the 50 Ohm 1 meter cable and the scanner I would insert a low pass filter. The BW limit has helped reduce the noise, but it can certainly still be further reduced without any lose to our signal. That's because we cut the beginning of the signal and then measure just the the decay time, which is relatively long and smooth (1 to 2 times 1/e US). Thus, in the future I may even want to try to eliminate the oscillations 320ns, but I'm afraid that this much filtering will distort the signal too. Therefore, for the immediate future I'm just looking to 'replace' the filter BW 20 MHz, with something like 1 or 5 MHz.

    Of course, I would disable the BW limit on the digitizer to avoid additional confusion, but nevertheless, I'm not sure how to approach the problem. Usually I do a lot of research and try different solutions. However, I don't have access to all components to this work, so everything should be ordered, and I don't have a lot of time to experiment. Ferrites seem like a possible solution, however not sure how effective they are at this low frequency or the way they work with coaxial cables. I know that the filter passes low RC base, but the 50Ohms (or 1MOhm | 30 pF if I change it) seem to make it impossible. I guess an op-amp based one might work, however the large input impedance is the impedance of coaxial cable... etc...

    All of the recommendations of the technique or red resources wort would be welcome. Thanks for your time.

    A possible way to separate your artifacts electric and the cavity is relatively simple.  You take the data at three wavelengths.  For each of them, make a simple exponential decay (for example exponential Fit.vi) adjustment to your data, then subtract this signal.  You should have something that oscillates on an average.  Compare the residual signals for all three wavelengths, either visually or with something like a power spectrum.  Anything in the three is probably the electronic (and you could possibly model and subtract it rather than trying to eliminate it).  This could break if the rise time of the signals are different, because that will include elements of different frequency.

    I am not convinced that you need to filter your signal before taking data.  As you said, any filter will distort your final signal.  My preference would be to take the raw signal and apply a filtering in the analysis.  LabVIEW has a rich filter, so you can experiment later.  If you apply a filter before the digitization of data, you take you will never receive data.  However, if you know that your data has no component of your proposed cut filter frequency, you should be good.  An analysis of the power on your current spectrum should tell you this.  Be careful.  Your form of rise time may have information you want later.  If you filter, you will probably slow it down.

    Good luck!  Let us know if you need more information.

  • Nexus 5548 continuously restart after installing licenses for L3

    Here is the situation - we bought recently L3 (N55-D160L3-V2) daughter cards for our 5548UPs as well as Services in Enterprise LAN licenses)

    N55 - LAN1K9).

    I installed the card and Ent Svcs lic this weekend last and all is well except that I could not activate the feature of EIGRP... apparently, EIGRP requires basic LAN (N55-BAS1K9-BUN) license even if you have the lic Enterprise installed, so I was able to dig up from this license afterwards (which comes with the L3 daughter card (, by the way). Another side effect do not install the Base of Lan lic, is the L3/card module will be in an "offline" status until the Lan Base license is installed. Whatever it is, everything worked normally in L2 mode at the moment.

    So here, I thought, I was ready to proceed with the activation of L3 - this morning, I installed the basic LAN license on one of the 5548 s who apparently triggered the daughter card module L3 get active and triggered a reboot of the switch. OK, not that big of knew a business, that was probably to come. I expect the switch to return to the top normally... NOPE. The switch is entered in a continuous reboot cycle where the console prompt appears, and then 30 seconds later, could restart again.

    Finally I ended up reinstalling the original map of L2 and the right switch came. I see that the basis of LAN and Enterprise LAN are both still installed as well.

    What have I done wrong here?  Why the switch changed in a continuous reboot cycle once I installed the basic LAN license?

    Thanks in advance!

    Here are more details:

    Software

    BIOS: version 3.5.0

    Charger: version N/A

    Kickstart: version 5.0 (3) N1 (1 c)

    system: version 5.0 (3) N1 (1 c)

    power-seq: Module 1: version v1.0

    uC: version v1.2.0.1

    SFP UC: Module 1: v1.0.0.0

    Compile of the BIOS time: 03/02/2011

    kickstart image file is: bootflash:/n5000-uk9-kickstart.5.0.3.N1.1c.bin

    Kickstart compile time: 04/05/2011 03:00 [04/05/2011 06:43:31]

    filesystem image is: bootflash:/n5000-uk9.5.0.3.N1.1c.bin

    compile time: 04/05/2011 03:00 [04/05/2011 08:35:20]

    !

    !

    Feature Ins Lic status Date comments

    County

    --------------------------------------------------------------------------------

    No. FM_SERVER_PKG - unused-

    No. ENTERPRISE_PKG - unused-

    No. FC_FEATURES_PKG - unused-

    LAN_BASE_SERVICES_PKG Yes - use never-

    LAN_ENTERPRISE_SERVICES_PKG Yes - never used -.

    --------------------------------------------------------------------------------

    !

    !

    Status of Module Type mod Ports model

    --- -----  -------------------------------- ---------------------- ------------

    32 1 O2 32X10GE/modular universal Pla N5K - C5548UP - active SUP *.

    3 0 ok O2 no L3 daughter card N55 - DL2<--- ***="" had="" to="" reinstall="" the="" original="" l2="" card="" in="" order="" to="" get="" switch="" to="" boot="">

    MOD Sw Hw World-Wide-name (s) (WWN)

    ---  --------------  ------  --------------------------------------------------

    1 5.0 (3) N1 (1 c) 1.0.

    3 5.0 (3) N1 (1 c) 1.0.

    I had a console cable connected while the reboots were happening though and I saw a bunch of ominous messages, which likely would shed light on the problem

    I would be very interested to see this.

    Mainly, I need to know if there is something I am missing here - does our IOS (version 5.0(3)N1(1c)) not work with our L3 daughter card (N55-D160L3-V2)?

    Hmmm... good point.  You can try 5.1 (3) N2(1a) or 5.2 (1) N1 (1).

  • ACS v4.0 license

    Hi all

    Is it possible to retrieve the details of the license of acs v4.0, which is already installed.

    also, can someone explain the available for GBA v4.0 licensing mode

    as:

    -It is based on the clientst AAA numebr?

    -It is based on the number of servers

    Kindly help

    Lunedor

    There is no such license basis of limitation. You can add as many devices you want.

    Kind regards

    ~ JG

    Note the useful messages.

  • 2 definitions of view based on the value of the table

    Hi all

    Is it possible to have 2 different definitions of each entry of 2 base tables display different, based on the value of the table?

    We have 2 tables with similar columns, one with historical and other data was only the latest / greatest according to yesterday (it is populated by ETL from mainframe). Changes made by the java application online is now going into the table containing historical data immediately, but edits made in mainframe comes to the table with the data current next day.

    There are 2 products, an is based on the last and largest of the historical table based on cre date and date of mod and other product relies on the table with the current data (not historical).

    Tried using joins for these two tables but the performance wasn't good and each product needs table data alone, and so I wanted to eliminate joins.

    We wanted to use the same name for the view from the metadata using the shared functionality based on the name of the view.

    Is there a way define a view under certain conditions?

    It is:

    If the value for a particular parameter is 0 then

    Select c1, c2, c3 of < historical table > other

    Select c1, c2, c3 of < no history table >

    Any ideas?

    You are looking for something like this?
    Re: how to pass parameters in a view

  • Incorrect IP address in AirPort Extreme Base Station

    I use a Vista PC. I have been using the Airport Extreme already. Recently, I try to make some changes when it starts. I accidentally pressed the wrong buttons. When changes are made and he ends by I cannot connect to the wireless device more. As shown on the start page the Airport utility, I find the last digit of the IP address as shown is incorrect, i.e. 10.0.1.200.  This should be 10.0.1.1 or 10.0.2.  How can I did it correct? It's because he just keeps asking my password and when I get it it fails just to connect. Someone help me please.

    You can replace the IPv4 DHCP range on the network > Network Options... page AirPort Utility. To the beach: 10.0.1.2 to 200 (the default), the base station LAN-side address will become: 10.0.1.1

    Temporarily connect your PC directly to the base via an Ethernet station so that you can access it then with AirPort Utility.

  • Satellite L650 - 1 DG - LAN is no longer connect to 1 GB

    Hello

    I have 3 laptops Satellite L650 - 1 dg ethernet port used to connect to 1 GB. Some time in the past months, it stopped. I tried the latest Atheros driven site without success.
    Windows says that the hardware is an Atheros AR 8152 PCI E Fast Ethernet Controller but it used to connect to 1 GB.
    Someone at - it ideas?

    Thank you

    Andy

    You are right. This model of laptop has Atheros AR8152 10/100 Base-TX LAN card.
    Now to maybe stupid question, but what is your problem. Is the transfer of data via LAN card too slow or what?

  • Satellite A105-S4064 - need drivers XP for LAN, video, Audio

    Hello

    I recently had to do a clean install of my Satellite A105-S4064 and have had problems to get the right drivers for it.

    On the Toshiba site, it lists only 4 drivers for XP for my model, even if that's what it came installed with. The video driver list and sound do not yet work for me.

    I need drivers for the modem, LAN, video, Audio, please.

    Any help would be a great help!

    Thank you

    Ken

    Hello

    On the page of the Toshiba driver we you can find the right driver for XP graphics card.
    At the moment the page provides a display driver nVidia GeForce (v83.02, 19/01/2006)

    I also found a driver of his right. It s a Realtek audio driver.
    If you need a more recent version, then I recommend to visit the site Web of Realtek and download the newest one.

    But note; the XP SP2 operating system needs and before install you the audio driver you must first install the Microsoft Hotfixes; KB888111 and KB835221
    After the installation of these two patches, you can follow with another audio driver installation.

    It also seems that this notebook would support an Intel PRO/100 VE Network Connection - 10/100 Base-TX Lan card
    So, you can visit the Intel page to get the right Win XP driver for this Lan chip.

    Good bye

  • License AnyConnect disables AnyConnect essentials

    Is this correct?  It does not seem right.  I bought a mobile Anyconnect license to add to my ASA 5505, who already had active Anyconnect Essentials.

    I received the watch activation key that I would go to:

     License : Base Max Physical Interfaces : 8 VLANs : 3, DMZ Restricted Dual ISPs : Disabled Trunk Ports : 0 Failover : Disabled Inside Hosts : 50 VPN DES Encryption : Enabled VPN 3DES and AES Encryption : Enabled VPN Peers : 10 SSL VPN Peers : 2 Shared SSL VPN licensing : Disabled AnyConnect Mobile : Disabled Linksys VPN Phone : Disabled AnyConnect Essentials : Enabled Advanced Endpoint Assessment : Disabled UC Proxy Sessions : 2 UC Phone Proxy Sessions : 2 Botnet Traffic Filter : Disabled 

    TO:

     Inside Hosts : 50 Failover : Disabled Encryption-DES : Enabled Encryption-3DES-AES : Enabled Security Contexts : Default GTP/GPRS : Disabled AnyConnect Premium Peers : Default Other VPN Peers : Default Advanced Endpoint Assessment : Disabled AnyConnect for Mobile : Enabled AnyConnect for Cisco VPN Phone : Disabled Shared AnyConnect Premium License server : Disabled Shared License : Disabled UC Phone Proxy Sessions : Default Total UC Proxy Sessions : Default AnyConnect Essentials : Disabled Botnet Traffic Filter : Disabled Intercompany Media Engine : Disabled Cluster License : Disabled vCPUs : 0 

    The Mobile license should not disable Essentials. That could be a mistake made by the license server.

    I recommend to open a TAC case and urging them to please put in the queue for license Global (GLO) operations. Request GLO re - issue an activation key which includes your already approved essentials.

  • VDA license includes OS Win license copy for the virtual office?

    Hello world

    We plan to go to desktop virtualization. For access to VDI, we were told that we would need microsoft VDA license that is a subscription based license. Main systems are thin clients and a few old desktops not covered do not SA
    I want to know if the VDA license includes OS Win license copy for the virtual office?
    Kind regards
    Vishal Claudia di Sisto

    Hi Vishal,

    Thanks for posting your question in the Microsoft Community.

    I question you posted would be better suited in the TechNet Forums.

    I suggest you to ask your question in the below link:

    Virtual server:

    http://social.technet.Microsoft.com/forums/en/category/VirtualServer

     

    I hope that the information above helps you.

Maybe you are looking for