Path will not close - generates a line in the opposite direction.

Similar Questions

• CD ROM tray remains open, will not close

  CD Rom tray will not close. When I restart the PC the tray closes but opens again and stays that way.

  Hello

  1. have you done any change in software on the computer lately?

  Method 1.
  If the problem persists, start the computer to start clean and control state.
  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2.
  Also, check with the manufacturer of the DVD drive and check for possible mechanical damage on the drive.

  I hope this helps.

• Photosmart 3210xi top will not close

  I have a HP Photosmart 3210xi that top will not close. It was opned the same as you would to change ink carterage

  I wish I had an easy answer for you. These hinges are difficult to reach. You could give a few quick shakes up or carefully lift the unit a few inches upward and drop the table to try to unlock the hinges. Put something to protect the scanner glass where the top down.

  I don't think that the cold would damage unless it was very cold, is it possible, that the plastic can get rigid.

• Windows Firefox will not close.

  Hello
  I am running windows 8.1 and Firefox 38.0.1. whenever I click on the Red 'x' to close Firefox, Firefox will not close. If I want to close all tabs, Firefox does not close the last tab. If I try to merge windows (by dragging the tab of a window in a different window) Firefox will create a blank tab on the window where I dragged the dragged tab. So far, the only way to close the Fire Fox is click on the close button or to stop by the Task Manager. When I re - open Firefox Windows and previous tabs are also there, and I'm still not able to close them. I restarted my PC and reinstalled Firefox (uninstalled and re-download). However, after downloading Firefox... the same windows will be opened, with the same tabs! It's horrible!

  Hello cach_dies,

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that temporarily disables hardware acceleration, restores some settings and disables add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • Click the menu button

    

    click Help

    

    then select restart with disabled modules.

  If Firefox does not work, you can start Firefox in Mode safe as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the problem is not present in Firefox Safe Mode, your problem is probably caused by an extension, theme or hardware acceleration. Please follow the steps described in the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. This might help others with the same problem.

• After IOS 10.0.2, camera will not close

  Just did the upgrade to the new IOS, and now everytime I open my phone or my pad, the camera is open and will not close. Reboots do not help.

  Hello. Can you explain more? You open the smart cover or click on the Home button and immediately see the camera? You should see the lock with a message screen to press home to open. The lock screen is now configured with the page today (widgets) on the left and on the right camera, so you can drag to get access without having to open the iPad. If you enter the camera, by error, by clicking on home leaves you.

• Web sites will not close. How can I force them? Cannot close their or firefox.

  I have three tabs that will not close or allow me to close firefox.

  Start Firefox in Mode safe to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  To turn on safe mode

  • You can open Firefox 4.0 + in Safe Mode holding the key SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • Or open the Help menu and click on the restart with the disabled... modules menu item while Firefox is running.
  • Once you get the pop-up, simply select "" boot mode safe. "

  If it works in Mode safe mode and normal mode with all extensions (Tools > Modules > Extensions) off and then try to find which extension is the cause by allowing an extension at a time until the problem reappears.

  Close and restart Firefox after each change via "Firefox > Exit ' (Windows: Firefox/file > quit;) Mac: ' Firefox > quit Firefox. " Linux: "Firefox/file > exit ')

  • https://support.Mozilla.org/en-us/KB/troubleshoot-Firefox-issues-using-safe-mode
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Keynote will not close

  I downloaded a PowerPoint to Keynote. When I tried closing keynote it will not close and stop me logging off my mac properly.

  You can use the keyboard shortcut leave force: Command + Option + ESC.

• Notification Center will not close on my ipad 2

  My notification/widgets page will not close on my IPAD 2.  When I drag the page, it won't move.  I can see my page weakly in the background with "slide to unlock" and the clock start, but could not get anything to move.  I wanted to try to start again, but I can't stop because I can't drag any suggestions?

  Hi ghartman1,

  Please visit Apple support communities.

  If you can't drag to unlock your iPad or turn it off, you can force it to restart:

  Restart your iPhone, iPad or iPod touch

  How to force reboot

  You must force restart your iPhone, iPad or iPod touch as a last resort, and that if it does not. To force the reboot your device, press and hold the two buttons of sleep/wake and home for at least ten seconds, until you see the Apple logo.

  You can also learn what to do if your device isn't yet to respond or turn on.

  All the best.

• Hotmail will not close due to open browser cookies

  Hotmail will not close due to open browser cookies

  Hi RogelioWelch,

  ·         What web browser do you use?

  ·         What version of the operating system is installed on the computer?

  ·         The question is limited to the hotmail only site?

  If you are using Internet Explorer, follow the steps in the article.

  Block or allow cookies

  Cookies: Frequently asked questions

  If the problem persists, you can also post your request in the forums of hotmail.

  http://www.windowslivehelp.com/product.aspx?ProductID=1

• All of a sudden my Acer Iconia One 10 will not close or disable. It flashes just the splash screen

  All of a sudden my Acer Iconia One 10 will not close or disable. It flashes just the splash screen "Acer Explorer beyond the limits; Powered by Android.

  What should I do?

  Problem with the cord/charge plug unit... is very loose and since I bought it. It takes an extraordinary amount of time to load. Is it defective?

  According to the description of the connection of the power supply or you have a problem with the power outlet (perhaps folded ut of shape enough to cause free adjustment) or Charger (connection flashing in-house, exit misfeed or simply that bad). If I was in your position I would take back and get one without load problems. You can send it through Acer support and they will fix it for you, but back to the seller will be faster.

• BlackBerry Smartphone app Center will not close! Help!

  I don't know if anyone has faced this... but my app Center will not close!

  When I pressed the bb and the small menu appears in the center of the app are still there... If I click on it it does nothing.

  I tried to reboot (battery and everything), opening center app (just opens a new one out while both are open)

  I don't know what happens >.

  also on a side note... a small blue apperaed icon next to my bars of reception with a symbol in it... i can look for that when I get home... but I didn't know that until today...

  The application Center never closes.

  you will always have a minimum of 5 'applications' running:

  App Center

  Browser (make sure that it is not on a web page)

  Home

  Mail

  'Call' screen

• LaserJet M452dw: Laserjet M452dw paper tray will not close

  Removed the tray paper to add paper and now the tray was arrested along with about 3 inches to go and will not close.  I also noticed that the drop-down menu that is located above the status bar was low so I pushed him to the top in place, but the drawer is still not closed.

  Problem solved, it was the length of tray setting that had to be closed for paper to letter!

• All the ' * .exe ' programs will not start by simply clicking on the shortcut icon.

  All the ' * .exe ' programs will not start by simply clicking on the shortcut icon.  I need a right click and select "Run as Administrator" to get the program to run. By clicking on the left, a box opens, which says "Windows cannot open this file: file iexplore.exe (example)". ""  It then goes on to ask if I want to use the web or select a program from a list of installed programs. Is there a way to get this back to "normal"?

  Hello

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be harder to detect as
  the cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
  It will display all the infections in the report after you run - if it will not run changed the name of
  TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
  check with the other methods below.
  http://support.Kaspersky.com/viruses/solutions?QID=208280684

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/products/malwarebytes_free

  SuperAntiSpyware Portable Scanner - free
  http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGE

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp?prevx=Y  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  -----------------------------------

  Original version is now replaced by the Microsoft Safety Scanner
  http://OneCare.live.com/site/en-us/default.htm

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  ----------------------------------

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  After the removal of malicious programs:

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  ======================================

  If necessary AFTER you are sure that the machine is clean of any malware. (DO NOT USE IF)
  MALWARE IS STILL PRESENT).

  You can try a repair install or an upgrade in Place.

  You can use another DVD that aren't copy protected but you you need to own
  Product key. It must be the same version 32 or 64 BIT Vista OEM. Also the system
  machine to usually sell the cheap disk since you already own Windows. Don't forget to make a
  good backup or 3 (security in redundancy).

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  =======================================

  For extreme cases:

  Norton Power Eraser - eliminates deeply embedded and difficult to remove crimeware
  This traditional antivirus analysis does not always detect. Because the Norton Power Eraser
  uses aggressive methods to detect these threats, there is a risk that it can select some
  legitimate programs for removal. You should use this tool very carefully and only after
  you have exhausted other options.
  http://us.Norton.com/support/DIY/index.jsp

  ================================

  If you are in North America, you can call 866-727-2338 for virus and spyware help
  infections. See http://www.microsoft.com/protect/support/default.mspx for more details. For
  international information, see your subsidiary local Support site.

  Microsoft support - Virus and Security Solution Center
  http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#TAB0

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Have a problem with Lightroom 5.4.  Given that the program crashed yesterday, will not start, it comes up with the message "Lightroom has encountered an error when reading the preview cache and need to quit."  "Lightroom will attempt to fix this ti net pr

  Have a problem with Lightroom 5.4.  Given that the program crashed yesterday, will not start, it comes up with the message "Lightroom has encountered an error when reading the preview cache and need to quit."  "Lightroom will attempt to solve this problem, the next time he throws."  Except that it isn't, I get the same message and the program closes.  Anyone know what I can do to fix it?  Can not backup, can't do anything.

  There are dozens of discussions in this forum that describe the fix

• MacBook Air will not recognize Micro SD disk in the format exFAT

  Hello

  I have a new camera of Campark Xtreme (like a Go Pro) who uses a Micro SD disk in ex FAT format. My 3 year old MacBook Air does not recognize the disc in this format. But to reformat, I need to erase all the content on the disc. When I put the disc in the camera, the camera will not work unless I have reformat the drive for exFAT.

  My computer is 10.10.5. So my husband. We have the same problem on two laptops.

  Anyone have any ideas?

  The Mac can read and write to exFat without problem. The problem is probably that the card is too recent for the readers into your computers.

  Fortunately, a new stand-alone USB drive which takes care of these maps is cheap.