Pavilion 17-g108na: selected boot Image is not authenticated

Similar Questions

• Selected boot image is not authenticated. Press on < enter > to continue

  I just removed the stock HARD disc that came with my M4-1015 x and now I am trying to install windows 7 on the SSD that I replaced it with. However, when you start up I get the message "the selected boot image is not authenticated to. "Press on < enter > to continue" when the laptop tries to read the operating system from the disk. I've never seen this before... any help? (This is a legitimate copy of Windows 7 DVD)

  Thank you.

  I fixed it. Of the secureboot to activate and deactivate bootmode inherited so he can work.

• "HP Pavilion X 360 13": HP Pavilion X 360 13 ' selected boot Image is not authenticated. Press on &lt; enter &gt; to continue

  Hi all! I was wondering if someone could help me. My laptop started to tell the boot image selected is not authenticated is and asks me to press on enter. However, whenever I do this, the laptop is just turns off. I have read through the forums and tried all unique methos. No matter what I do, I can't access and type of BIOS or diagnostic, everything I chose makes it go to this screen. If you could give me any help, I'll be very grateful. It comes preinstalled with Windows 8 and has since then been upgrade Windows 10.  Also, when I turn on the computer, I heard a strange buzzing of the mouse pad area, what is?

  Thank you!

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Oops, I didn't add this.

  Oops, I didn't add this.

  Hey there! @mycatdaphne, thanks for the reply.

  Thank you to perform troubleshooting.

  As you mentioned that you still can not access BIOS.

  It's a hardware issue please contact HP support for service options.

  Link to contact HP: http://hp.care/2bkTGBQ

  Have a great day!

• selected boot image is not authenticated

  I just bought a new HP ENVY-4 with pre-installed Windows 8.

  After a few weeks where it has worked well, the computer began to get into trouble. Then he simply did not start more. As I shitch, stay for a while with black screen and then a blue mask pops up saying 'the boot image selected is not authenticated to. Only chance is so press ENTER, then the computer off completely.

  I am hollow your forum and try to almost everything.

  Tools of recovery to run, but not to solve. After treatment, the problem is still there.

  I noticed that if I try to run the "repair of the problems at windows startup" tool, computer said it was not able to repair...

  I open BIOS and changed the relevant setting ensure also the start-up and mode inherited... the computer simply does not start!

  I finally re-formatted the french PC key to restart USB, (made with the HP support tool, when it was new)... same problem appear like I'm back!

  Can you help me please? 3 months computer brand is new and I really disappointed to trow away my money.

  Thank you

  effebbi,

  If your battery off not easily with a lock at the back of the laptop, you can hold the power button for 30 sec with the power cord removed to do the same.

  I would like to know how everything goes

  Nice day.

• n005tx Pavilion 15: "selected image is not authenticated to. "Press on enter continue" at the start of the

  Hi all, I have a pavilion laptop g6 - 2253ca who works with a windows 8 (64-bit). I have a strange problem since this morning and an error msg "selected image is not authenticated to. "press on enter continue ' that appears when I try to start. I have not installed program on my computer before it happens. I just sailed on the Internet and all of a sudden the screen is grey and the msg appeared on this subject.

  I went on several forums for information on this subject. That's what I did:

  -hard reset
  -Restart and boot into BIOS
  -Disable secureboot and enable legacy initialization
  -Press F10 to save and exit BIOS

  -Restart

  -the system asked me to enter a digit of 4 password and press ENTER to apply the changes

  -done, but I got stuck another MSG: "no boot device, insert the boot disk and press any key.

  Not able to find something else to move to another service I thought that maybe the value default bootable device was not the HARD disk if:
  -I restart and boot into the boot F9 Manager
  -does not not the same msg (no boot device, insert the startup disk and press a key) is displayed.

  Try to run the auto repair using the F11 Recovery Manager, but I can't start on it during startup.

  So, what should I do now? I am really disappointed...

  Hello

  Try loading at F2 run check disk test hard if that passes you will need a recovery disk. If the hard drive is not detected reinsert the disc hard try to rerun the test if you have the same hard disk problem that went wrong to replace the drive. Please call HP technical support check for warranty and the part replaced.

• HP Pavilion G6-2292SA: selected image is not authenticated

  A few months ago my laptop came with the message 'selected image is not authenticated to' but I just left him because I was in the middle of loads of deadlines United and had no time to try to sort them. I turned on my laptop about once or twice since then to see if there is no change, but he always showed the same message. When I turned it on today to try to sort it's just come up with a white screen, the black light is turned on and when I press like f10 things happens at the bottom of the screen with "F10"... BIOS Setup Options"but that's all that I can see, I can't seen of these 'options '. Pleaaaase help

  @sofiabruna,

  Thanks for posting back.  Here is the link to your maintenance and service guide.  Here the reference numbers and support for hard drives.  Then, you can contact HP shopping for pricing.

  Maintenance and Service Guide

  Here is the link to HP Shopping.

  Thanks again for posting and have a great day.

• By selecting multiple images does not

  I am a beginner, through Classroom in a Book, Lesson 5. I'm trying to select image 56 on three different lines. When I use the SHIFT key, it highlights the complete on lines 2 and 3 motion tween. I need only frame 56 selected. What happens here? Can someone tell me why is to select the entire line?

  It is likely that it doesn't matter that the entire span is enabled, when you make a change to something with a motion tween, only the current frame is changed, even if the entire duration is selected.

  For peace of mind you can click and drag, cell framework in the first layer down to the same framework in the last cell layer.

  But as I said, I don't think it will be question anyway.

• 15 - f233wm: cannot install boot CD Linux - image will not authenticate

  I activated the inheritance initialization and secure boot disabled in BIOS and then saved and restarted and also upgraded to the latest version of the BIOS F.29, then press ESC-> F9 on startup to select CD-ROM, I get "selected image is not authenticated to. Hit to continue.

  It is a good of Jessie Debian production x 64 install DVD used successfully on lots of boxes. I also tried an external USB CD-ROM, with the same result.

  My original and fully patched and updated Windows OS 10 boots yet, but I need Linux on this box. I want to use EasyBCD to manage the boot process, but I still need to get the boot CD to install on a new partition I created after my main of Windows NTFS partition resizing.

  It seems that the boot order is set to the OS boot manager. You must move the pointer to the legacy options. That's why it shows boot UEFI options because the default option is the Boot Manager.

• Update CAN´t SRW2024 to firmware 1.2.2 without boot image "runtop_boot - 101.rfb".

  Hello

  I need a little upgrade to a SRW2024 assistance to the latest firmware.

  I started with the upgrade to v.1.2.2, but just started switch to reboot all the time, I flashed back to 1.0.0.86 xmodem console.

  On the FAQ of Cisco theres a guide how to change the SRW2024. The guide says that I have to update the boot image before flash image, but the boot image is not available on the download section of cisco´s more.

  Can you please help me with the boot image. (runtop_boot - 101.rfb)

  Thank you.

  Hello

  I hope you called the HWC, since they have not yet responded to this request.

  http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

  Best regards, Dave

• HP Pavilion 15 laptop: boot image selected is not authenticated

  When you turn on the laptop says «boot image selected not to is not authenticated...» "What do I do?

  It's your computer laptop one with a removable battery?

  Remove the battery, unplug the power adapter and press and hold the power button for about 15 seconds. That will reset the hardware of the laptop.

  Put the battery back in and press the power button.

  Post your results here if you please.

• HP 250 g4: boot image selected is not authenticated

  Hello, my computer has problems from the beginning. One day, I restart my pc and this appears:
  "Boot device not found.
  Please install an operating system on your hard drive
  Hard drive (3F0)
  The F2 System Diagnostics.
  So I did all the tests diagnostic tests and all translate "SUCCESS."
  I called support and they are sending me the two DVD «Recovery media for windows 10 products»
  I followed the instructions and put the first DVD, and then I started the pc. At first, it seems that the cd will then start appears this sentence "the boot image selected is not authenticated to. Press to continue.
  What could I do?

  Hello

  Try the following.

  Judgment of the laptop.

  Click next to the ESC key as soon as you press the power button to enter the Boot Menu, and then select the Bios Menu ( f10 ).

  Under the System Configuration tab, expand the Boot Options Menu.

  Select 'Clear all secure startup keys' and click Ok

  Select "load factory defaults keys HP", and then select Ok

  Save the changes that you exit the bios and try to re-run the recovery DVDs.

  If you still receive the error, return to the Bios Menu, System Configuration tab and expand the Boot Options Menu.

  Activate 'Legact Support' and save the changes that you exit bios - you will then need to enter a PIN of 4 numbers displayed on the screen to confirm the changes to the settings - enter the code and press ENTER.

  Try to run the recovery dvd.

  Kind regards

  DP - K

• HP ENVY m6: boot image selected is not authenticated

  I need advice. "" When I turn on my laptop (HP ENVY, WINNING 8) computer I get the following message: "boot device could not authenticate press enter to ' when I have c: it stops. I can't boot into recovery mode either. What the hell went wrong?

  Well, I decided to bring it to the store from my friend, he is a technician and then of course he actually decided that he would start the operating system. He wasn't healthy but, we tried a refresh, but it stopped in the middle of it due to a disk hard w / the question. After that some of diagnotics hard drive was the culprit, so after a permutation we run once again. I'm fine w / start again as it works now. And I called HP ordered my backup disks. Thanks for the help, I would have had the discs that we would have come to the same conclusion I'm sure.

• When I change my background in my settings, it always enlarges the image no matter what I have to do select. He's not mosaic, Center, made

  When I change my background in my settings, it always enlarges the image no matter what I have to do select.  It will not tile, Center, adjustment etc. Only, even with slideshows, stretch my photos.  Is there some setting that is locked I need to uncheck?  Help!

  Original title:

  Computer background

  Hello

  • If it works well before?
  • What were the changes made before the problem occurred?

  You can view these methods:

  Method 1:

  I recommend you perform the clean boot and check.
   
  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.
   
  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135 
   
  Note: after a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  If the problem persists in safe mode, create a new user account and log on to it
  see How to create and configure the user accounts in Windows XP .
  b. connect on the new user account and check if the problem persists.

• HP Pavilion A6722SC: reboot and select proper boot device or insert boot media in selected boot device and press a key

  My computer has just stopped working and when I turned it on, it says I should change my hard drive. I did, but now the message is whenever I turn on my computer: reboot and select proper boot device or insert boot media in selected boot device and press a key.

  I have Hp Pavilion A6722SC. I have my 1st drive on the driver that I bought and I have the Boot Device Priority :

  1st boot Device [hard disk group]

  2 St boot Device [CD-ROM Group]

  3rd boot device [network startup group]

  4 rd boot Device [group Floppy]

  -> Disk Boot Priority group [not installed]

  -> Group of CD-ROM boot Priority [DSK02...]

  -> Group of HDD to boot Priority [DSK00...]

  -> Group network boot priority [not installed]

  I saw that many said I should disable the floppy, or I should have hard on the boot device 1 or driver, but this doesn't work for me. Someone who have solved problems of this kind? I need help!

  Thanks in advance.

  Sorry for the bad spelling.

  I needed a new OS... I had Windows Vista and I can't install it more, so I have to buy a new OS.

• HP Pavilion dv7 Notebook PC - Windows Boot Manager does not allow me to restart the laptop

  HP Pavilion dv7 Notebook PC
  XH121UA #ABA
  Office home and Student 2007

  I turned on my laptop and got the following message is displayed:
  Windows Boot Manager
  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:
  1. Insert your Windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."
  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.
  File: \Boot\BCD
  Status: 0xc000014c
  Info: An error occurred trying to read the boot configuration data.

  I had no problem before now with the computer. Yet once, this message has occurred during a turn on my laptop. I tried to restart the laptop, but it is not allowing me to restart. The laptop back to this message.

  I appreciate any help with this issue. I thank very you much for your time and knowledge.

  Hello

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO relevant among the links below.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.  One time created, or if you already have this, typing away at the esc key when you launch Notepad to open the Start Menu.  Insert the rescue CD.  Select boot options (usually f9), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  When loading, select repair your computer and choose the command prompt.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart the laptop.

  Kind regards

  DP - K