PAVILION 7955 memory increase

Similar Questions

• Locking of the Pavilion 7955

  I have a HP Pavilion 7955 about 5-6 years with XP, CIP 6 I think. The original memory has been increased, but that's all that has been done for her. I have McAfee (updated constantly).

  My problem is this: sometimes when I'm online and work the thing just freezes and won't do anything. I have to turn it off and restart. Sometimes, it will close and restart automatically. Sometimes when I leave the computer for a minute or two and the screen saver (family photos) are running it will stop just with part of the image.

  McAfee rises and says that my computer is "inadequately protected". If I try to run the "fix" just, it goes for a few seconds and turns off the remedial program without solving the problem.

  I got to say the following. "was caused by the storage driver Intel (IdeChnDr.sys), which was created by INtel Corporation. This product is no longer supported by the manufacturer. »

  He recommended that contact Intel. I tried (on their website) and they recommended that the manufacturer of the computer for hotfixes or updates. So here I am.

  One thing McAfee said was that if I was unable to fix the problem and continue to have errors, I can uninstall the storage driver Intel (IdeChnDr.sys). What would that do?

  I have tryied just go to McAfee Security Center to check the current status and it won't even happen when I click the icon.

  Looks like you have a bad sectors on your hard drive. You can either isolate the defective sector to tell the drive to 'jump' at the wrong place, or you can back up all your data and install a new hard drive (make sure that you have recovery discs).

  Here's an article on Scandisk - you can use it to isolate areas... may take a few hours.

  http://support.HP.com/us-en/document/bph06946

  Message edited by RasterBlaster on 29/04/2009 12:43

• HP Pavilion 15 PC laptop: HP Pavilion 15 memory update

  Hello

  I plan to upgrade my laptop HP Pavilion 15 memory PC J2C73PA #UUF.

  Is it possible to use the Kingston memory module?

  What is the maximum capacity can I install on my laptop?

  Can I install modules with 1.5V?

  One installed on my laptop came with 8 (GB Elpida 1600 MHz) which is not available here in our country.

  Hope someone can help me with my concerns.

  Thank you

  Neil

  Here is the Service Manual:

  Manual

  All your questions are answered in the manual, except that the manual indicates a maximum of 12 concerts, and it will take up to 16 GB. It only uses the 1600 DDR3L which means 1.35 volts only as long the memory is the same specifications and configuration as the original, yes you can use Kingston memory.  Pay attention to the voltage (1.35) and density (4 blocks of black on the side) or 8. It must match the original or modules.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Clarification needed Pavilion a1120n memory upgrade

  First time on the Forum, need for clarification after reading others entry and to collect the necessary information on the PC in question.

  HP Media Center Edition Pavilion a1120n

  Processor: Pentium 4 519 (p) 3.06 ghz

  Motherboard: Asus LRTP - THE (3 goldfish - GL8E) front bus at 800 mhz

  Will support maximum 4 GB of ram

  Unit is equipped with 4-240 pin Dimm, unbuffered, non - ECC 533/400 mhz sticks memory memory DDR2, dual channel architecture

  This office has 2-258 or 516 MB PC2 3200 DDR SDRAM OEM.  I opened the unit to check for this.

  OEM preloaded with Windows XP Media Center Edition.

  Now, most anyone looking at this request, probably why I'm wanting this on such an obsolete machine...

  I have bought new at the beginning of 2005, used the PC for a few months, remarried & it packed to move.  My husband had a Pavilion, so instead of having 2 running side x side, I copied my files in his unit, left (the most recent of the two) packed mine, thinking that we would need it down the road.  The road became long 7 years.  More to the story, but I'll spare you the pain. The only way I can use this material is upgraded to Windows 7 home & I need to increase the memory to install even.  It will be dedicated to the dissemination of music on the internet in the shop, period.

  Here are the complete specs for your HP Pavilion a1120n desktop and it is card mother PTGD - THE (Goldfish3). Please consider the purchase of 2 of the CORSAIR 2 GB Kit (2 x 1 GB) 240 pin DDR2 533 (PC2-4200) VS2GBKIT533D2 or 2 of the Crucial 2 GB kit (2 x 1 GB) DDR2-667 PC-5300 #CT475923 to bring your computer to the 4 GB maximum, it supports.

• Pavilion g4: LM753LA: increase the RAM in HP Pavilion g4

  Hello

  I want to increase the RAM on my HP Pavilion g4. I don't know what is the model number, but I'm sure the product number is LM753LA.

  Can you help me please to understand what I can buy RAM? Today it has 3 GB (I think there are two slots: 1 x 2 GB and 1 x 1 GB) and I would replace the 1 GB of RAM with 4 GB of RAM, that's good enough for me.

  I understand that I must choose a memory as follows:

  • 4 GB (to replace the 1 GB)
  • DDR3-SDRAM
  • 204-pin SO-DIMM

  Does make sense for you?

  Are there other features should I consider to make sure that the memory works in my notebook? MHz FSB, voltage etc. ?

  Thanks a lot for your help!

  Best regards

  Mario

  I found the following information, maybe it helps:

  http://ICEcat.biz/p/HP/lm753la/laptops-G4-1064la-10772223.html

  

  And this is my laptop:

  

  Hello

  The card says 8 GB maximum in two slots this means that you can use only 4 + 4 GB. If you have 6 GB, you will need to buy 1 stick of 4 GB and use existing key to 2 GB. CPU - Z shows you all the information you need: brand, RAM card...

  Kind regards.

• start using SD in Pavilion dv2000 memory card

  Hello

  I wanted to boot from SD memory card in my HP Pavilion dv2000 laptop. What should be the BIOS for this setting.

  Thank you!

  Shivchal

  I don't think that you can start from your reador of card for laptop

  but you can start from your SD card using a USB card reader

  But u should create this card as bootable,

  There are many free application on the internet, just google,

  and make your bootable SD card, then use it.

  I used "USB_MultiBoot_10" and I create a portable bootable computer cos XP instalation disk of my father, dvd does not work.

  I do not have the link at the moment. but I got frm google search.

  Have FUN BRO,

• Satellite A60 - memory increased

  My Satellite A60 has 256 MB of memory and is vey slow these days. I removed several applications, but he healed partially the problem. I also defragment the hard drive. Could I need more memory?

  Counsel would be appreciated - how get it and install it?

  Hi Charles,

  Increasing your RAM will be an improvement, but only with applications that are particularly intensive memory. It is heavy graphics using games and utilities such as photo manipulation, video editing etc.

  It is much more likely that your system is hampered by the excessive task that runs after your first commissioning. Check in your task for the background process manager how you running and how much resources they actually are using. For a typical installation of XP, I would expect that there is between 45-50 running processes.

  Unless you have already done so I would recommend running a spyware (ADAWARE SE and SPYBOT S & D) utility that can be freely downloaded from the Internet, to see what presents itself.

  I see that you have already defragmented your drive hard, which is great, but I highly recommend running the disk cleanup utility as well to get rid of all unnecessary clutter.

  With regard to the RAM, I believe that the maximum that you can expand to 1280 Mb is, and I would recommend that you use Toshiba or RAM Kingston modules like these are tested to work with your laptop. I also used the modules of ORCA in my own laptop wuite successfully. Really, the choice is yours.

  Information on the replacement of the RAM modules are usually contained in the manual of your users and should also provide details of the procedure to follow.

  HTH

• Computer ze2315us Pavilion laptop memory upgrade

  I have install 2 GB of ram in the system, and now it crashes at startup, after talking with a technician in Kingston, he said that my system could a maximum of 1 GB, 2 x 512. My question is there a flash update or a way to change the max memory in the Bios?

  The controller memory your laptop uses ATI RS200M series of Northbridge. It may only be able to treat up to 1 G (2 x 512 MB).

  There is no update of the BIOS can increase the address space for this memory controller and therefore it is the maximum space of memory for this series of laptop.

• Pavilion G6 memory upgrade

  I'm looking to upgrade to 4 GB memory on my g6 pavilion laptop, but want of memory site to know what version of the g6, IE there are several dozen computer laptop g6-xxxx numbers of model in the list, so he can advise the best elements.

  The pages of OS system information and Device Manager the list just like a g6 pavilion, and the physical label on the back of the camera is not even go that far.  It does not list the item such as a 584037-001, whatever that means.  How can I know which (the suffix xxxx g6) my g6 is in fact so I can identify the best modules of memory for an upgrade?

  Davdik10

  You have a laptop HP Pavilion 2002au g6. Unfortunately you happened to choose a laptop that is not so simple to upgrade.

  You will need to contact an online memory provider and ask them for help to find a guaranteed compatible 8 GB upgrade or buy the upgrade from HP.

  Search for suppliers of memory online using Google or Bing and ""memory upgrade HP Pavilion g6-2002au ' as keywords. " I strongly recommend that you don't settle for anything memory compatible modules less guaranteed by well known memory manufacturers.

• HP Pavilion Dv6 Memory Upgrade

  Hey, I recently bought a HP Pavilion Dv6-6c14nr, and I'm looking to upgrade to 4 GB memory to 8 or 12 GB. I run a large number of programs such as Maya and UDK 3D so I would get an extra kick. I was told that it would be wise to get the same manufacturer as the memory chip that is inside the laptop now for best results. Is this true? Go to the basics, which module of memory should I go with, and is there a way to know what brand the stock memory is without removing the laptop support?

  Hi, it is recommended to use the same but not necessary memory sticks. I had a better memory reference with two different modules (2 GB + 4 GB) that the same sticks (4 GB + 4 GB). Crucial memory Advisor says that you need the sodimm PC3-10600 or PC3-12800 ddr3 modules. I recommend the modules 3-PC-12800 Corsair, Crucial or Kingston. HP uses Samsung memory modules in laptops, so you can get these institutions. Simple 8 GB modules are quite expensive, so it's in your pocket which modules to choose from...  :-)

• Pavilion m8187c: memory gap

  I added two memory modules more increase from 2 GB to 4 GB.  Systems to check installed reports 4 GB, 3 GB of physical memory, and 1.84 GB of free memory.  I get that little memory is used by the applications of background, but this seems to be an excessive injection of memory available.  Is this reasonable, and if not, what can I do about it?

  Hello

  Depending on your hardware configuration, 3 GB could be on what will be available. Hardware and system reserved areas may take up to 1 GB. The best I've seen is about 3.4 GB to 4 GB with a 32-bit operating system.

  Some ways to better maximum 4 GB using is to use a discrete graphics card that has dedicated memory.  Memory management would be greatly improved by using a 64 bit W7, W8 and W10 OS if these operating systems (OS) are compatible with your PC.

• HP pavilion p6000: memory upgrade

  Have a Pavilion p6000, SN MXX0490MHH, product # BT543AA #ABA.  Provided 4 x 2 GB with 8 GB of ram installed on the chips.  Operating system is Windows 8.1.  Upgrade to 16 GB and bought 4 x 4 GB DDR3 1333 MHz, DIMM parts.  Does not seem to accept the new memory.  Question: Is this good memory, and this system will support 16 GB.

  Hello

  Explain what "is not except" means. Windows is not except the new memory or the BIOS does not recognize the memory or the PC does not start with the new memory?

  We cannot answer your question, given the information you have posted.  You can certainly search the forum for others who may or may not have success the upgrade of your particular PC model to 16 GB.

  Try to clear the CMOS memory. If this does not solve the problem then test each one dimm at a time.  Don't forget, with the former PC HP DIMMs need to be a game.

  Try this memory bootable Diagnostics CD. Download memtest86 iso file and burn the disk using Imgburn.

  Memtest86 4.20 more Installer USB.  Test each dimm one at a time then as a complete set.

• Memory increase in LV2009 but not in LV8.5

  Hello.

  I developed the application that can be very simple. It opens 20 .NET object references, call the .NET method and close 20 references. This is repeated for each iteration. I develop this application in Labview 8.5, but it will run in Labview 2009. So I test it in Labview 2009 assessment. After a day application have crashed because of "Labview memory is full." I noticed that the memory is increasing if the application is running. So I ran the same application in Labview 8.5 and the memory usage has not changed since the beginning (the application runs for 3 days now). Is it because Labview 2009 is in evaluation mode, or is the problem somewhere else?

  Thank you

  Andrej

  I wrote my previous post a little fast. After further testing, I can confirm that there is no memory leak in my application after you install the hotfix f2.

• cluster with images: memory increases up to more than 2 GB and crashes

  I have a lot of PNG images (around 1200, 12 MB in size) and I load by programming in labview with a loop for I put all the image data in a table for all images.

  I can't complete this operation, while the images are very small memory LV is increasing more than 2 GB and then I get a memory error output.

  I put one "structure" above all table operations. What is going on? IM really a bad thing, I guess.

  Hi, Faust,.

  "On the qualities of the picture, they are 32-bit and x 850 360 pixels BUT about 99% is transparant (images has a constant size which is transparant, there is a small object that moves in this space)."

  Transparency is not relevant in terms of memory occupation. When the image loads, it just needs 850 * 360 * 4 bytes (or ~1.2 MB)...

  Suggestion:

  -Do not store images in memory... Do the math in slices of (say) 100 photos.

  -Do some manipulation of the image to get the position of the moving object. Then you store only a small portion of the image (with the object) and some information about the location in the picture. In this way, you always know the size of the (original) photo, but you only keep the "interesting" part in memory!

• Pavilion dv6-1305sl: increase in ram HP Pavilion dv6-1305sl

  Hello
  I have a RAM upgrade to my pavilion dv6-1305sl.
  Standard Monte 2x2gb PC3-10600 DDR3 ram. (controlled by CPU - Z)
  I want to get up to 8 GB (2x4gb)
  In the specifications of my computer provided by HP, it says "Allows up to 8 GB of DDR2 memory."
  Why ddr2? is a mistake?
  If I'm looking for Crucial or Kingston give me also compatible effects of ddr2 ram!

  The manual is wrong!

  I just installed 4 GB of RAM DDR3 PC3-10600 2 x Samsung... and everything works perfectly!