Pavilion a1620n won't start, the fans are not running. PS on the light and Sun. Start button does not illuminate

Pavilion a1620n won't start, the fans are not running. PS on the light and Sun. Start button does not illuminate. EU tested ps and I was told it was OK. Disconnected from the motherboard except course before directed ps button and the cpu fan has become much brighter, but that's all that happened. Any suggestions on what to check? Checked with VOM push and he seemed to agree. Replaced the MB with the new Board of Directors, that didn't work either. Don't know if it was any good, it was a store Bulletin Board.

All the indicators you mention leads to the PSU, not the Board of Directors.

Tags: HP Desktops

Similar Questions

  • The fans are not stop working after upgrading BIOS on Satellite A200

    Hello

    IM using the Satellite A200-1bp. I recently updated my BIOS 5.20 - winner and my fans are not end all the time working.
    I think his reason is update BIOS
    I'm looking for the BIOS below.

    Please help me...

    Hello

    Maybe this thread can help http://forums.computers.toshiba-europe.com/forums//thread.jspa?messageID=128543

    Make sure that you use the right BIOS for your laptop model.

  • Satellite P100-324: the Fans are still running

    Hi to you all,.

    Maybe you can answer me the question.
    Is it normal that my laptop fans are still running. I put the 'silent' settings in the bios and forced the laptop to run always on 1000 MHz, if I only use it for writing
    in Word or reading emails.

    It's really annoying. I don't know what to do.

    Thankz for your help in advance

    Michael

    Hello Michael

    It is nothing unusual that cooling fan runs constantly on low speed. On modern laptops, there is a powerful hardware that needs to be cooled correctly. Especially many different processes are active in the background and CPU is standing under pressure. Not much when you use just the laptop for writing, but obviously enough to increase the temperature of the CPU.

    Try it please set the CPU and cooling to a minimum level method. Also check the Task Manager and end the process, you don't need. Maybe this will help!

  • Start button does not work

    I have a Toshiba laptop.  I have recently upgraded to Windows 7, using all the programs compatibility of Microsoft and Toshiba.  I got the green light and the message that Windows was installed correctly.  Now, however, my Start button does work only intermittently.  I reboot and reboot until he gives up and lets me access my programs.  This isn't something that happens because I did not start the computer place correctly.  Sometimes it stops after I used the computer for hours of work.

    Hi chrisnjeanne,

    1. you did it all change in software to the computer lately?
    2 what happens when you click on the Start button?
    3. press the windows keyboard and check.
    4 I suggest you to update all the drivers from the Web from Toshiba website.
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

    5. clean clean boot:
    1. click on start, type msconfig in the search box and press ENTER.
    The user account control permission.
    If you are prompted for an administrator password or confirmation, type
    password, or click on continue.
    2. in the general tab, click Selective startup.
    3. under Selective startup, clear the check box load starting points.
    4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
    5. click on OK.
    6. When you are prompted, click on restart.
    7. after the computer starts, check if the problem is resolved.

    If the problem is resolved to check what is the cause of the problem, referring to the link given below:
    http://support.Microsoft.com/kb/929135

    8. in addition, you will need to uninstall and reinstall the software problem on your computer.
    Reset the computer to start as usual
    9. When you have finished troubleshooting, follow these steps to reset the computer to start as usual:
    Click Start, type msconfig.exe in the start search box and press ENTER.
    10. If you are prompted for an administrator password or for confirmation, type your password, or click on continue. On the general tab, click the Normal startup option, and then click OK.
    11. When you are prompted to restart the computer, click on restart.

    It will be useful.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How can I get rid of a popup telling me I have a virus Zeus.  It locks my screen and try to "erase the history and data, etc." does not work.

    I need help with a popup that locks the screen of my iPadAir2.  Go to the setting and compensation history/data does not work.

    If you have deleted the historical data and Safari Web site, and nothing is resolved, the problem is on the wireless router. Check your router wireless for possible violations.

  • When I click on the new tab, new tab button does NOT open.

    When I click on the new tab, new tab button does NOT open.

    Please update your browser Firefox 3.6.24 or 8 and check

  • How can I restart my iPhone 5 c? I tried to connect to iTunes and that has not worked. Then I tried now the home and sleep/wake buttons simultaneously, but that no longer works. My charger works. What should I do?

    How can I restart my iPhone 5 c? I tried to connect to iTunes and that has not worked. Then I tried now the home and sleep/wake buttons simultaneously, but that no longer works. My charger works. What should I do now?

    Looks like a hardware problem (with your home button).  You should probably make an appointment with the genius of Apple on an Apple store near you.  This link can help:

    https://www.Apple.com/support/contact/ >

  • Disable the sleep and Sun on

    Is there a way to disable the sleep and Sun on an iPad in flex?

    Artour,

    You can use this to turn off sleep:

    NativeApplication.nativeApplication.systemIdleMode = SystemIdleMode.KEEP_AWAKE;

    -Jason

  • "Pavilion dv6000 won't start after inserting the password

    I have a dv6000 Pavilion laptop with Windows 7 Operting System.  After a few recent updates at the beginning of my use of the computer (instead of at the end of my computer use), when I turn on the laptop, it brings up my user name and a password field, which, once I insert the password, it should redirect me to the window of the Application.  But after having inserted the password, the word "Welcome" with a circle of rotation appears on the display screen. This ' circle' rotates to progress to subject one minute and then display will Dim and never produced the home screen of the Application.  I greeted the dark screen to stay on the computer for more than 5 minutes and the House request never appears.  The only way to shut down Windows is to press Ctrl-Alt-Del, which produces a window with the following options: 1) lock this computer 2). Change user 3.)  Close the session 4) Change a password 5). Start the Manager of tasks with a button CANCEL in the center of the display and of the farm to the bottom of the icon in the lower right with the following options: 1) 2 restart.) (Sleep 3). Hibernate 4). Stop.   I used the option of doen stop to turn off the laptop.  What can I do to solve my problem and use the computer that I use for?

    Hello

    You are welcome

    I suggest you download AdwCleaner this link to delete the associated files - Save in your downloads folder.

    https://toolslib.NET/downloads/finish/1/

    A once downloaded, close all programs, open your download folder and double-click the application to run it (click Yes to any uac prompt).

    Click the scan button.

    When the results are displayed, click the Clean button - when you are prompted to restart, click Ok.

    Best regards

    DP - K

  • HP Pavilion p6510t won't start, need help!

    Hello, we have your desktop HP Pavilion p6510t with the following specifications:

    HP Pavilion p6510t PC

    • Genuine Windows 7 Home Premium 64-bit
    • Intel (r) CPU Pentium (r) Dual-Core E5400 (2.7 GHz, 2 MB L2, 800 MHz FSB)
    • SDRAM DDR3 800 MHz 4 GB [2 DIMMS]
    • 320 GB HDD at 7200 RPM SATA 3 Gb/s
    • Microsoft Office Starter 2010
    • No additional security software
    • Integrated graphics - Intel(r) Graphics Media Accelerator X 4500 [VGA]
    • No speakers
    • LightScribe 16 X MAX drive DVD +/-R/RW SuperMulti
    • Built-in Ethernet port, wireless
    • Audio Reader, 2 USB, 15-in-1 memory card
    • No TV Tuner
    • Integrated sound
    • HP USB keyboard and optical mouse

    We also bought this monitor to her (though I doubt it's important in this case):

    HP S1931a 18.5 "diagonal LCD screen

    The problem started about two months ago when the computer turns off without reason then that slowed down (before sleep should have started). After the computer restarts, he gave the beep codes that there was a problem with memory (1 short beep, 1 beep, long pause, repeat) long. After power back off and remove all devices and the power cable, the RAM has been removed (2 x 2 GB), checked for dust, bad seats, pins bent, etc...  The 2 RAM sticks have been resettled and the problem seems to be resolved.

    Fast forward two months (a bit more under warranty), the same problem occurs. This time, replace the RAM has not fixed the problem. Sometimes the computer should boot properly and then randomly cut regardless of what the processor was doing (idle or under load of 25% or more). In addition, beep codes would perhaps only half the time where it would not start. The output has been verified for feeding and another (proven) outlet has also been tried. No change. At this point, the computer won't be enough for any start screen at all, not even a blue screen.

    What he do to power on:

    • All powered fans (power supply, fan CPU cooler, case) and a spin at full speed.
    • Hard drive to wind up.
    • Green light on the power supply remains stable.
    • VA CD drive open and close normally.

    What is does not power upward:

    • No display at all.
    • No beep codes.
    • No blue light on the button walk / stop (top of case).
    • CPU does NOT get hot to the touch after 5 seconds to be under tension (with the fan and the heatsink removed and unplugged).
    • With two strips of RAM not removed, no beep of any kind.

    I also tried to use an old video card, I had to hang out, thinking that maybe the onboard graphics card were no longer works. The video card gets power as his fan runs, also at full speed. Still no display.

    I already bought a pair of replacement RAM sticks, exact same specifications and brand (Crucial), no difference. I tried all combinations of each stick into each slot with the original of the RAM in the first place, so I assumed it was sticks and replaced. Now that the RAM has been replaced and no beep codes, I suspect the motherboard or the CPU.

    I also tried to reset the BIOS by removing the battery for 10 + minutes and also move jumper to 2-3 1-2 during 10 seconds and replace (with power off).

    What I want to know is which component I need to replace to get this computer working before its tax season. I'd like to think it's the processor, because it remains cold to the touch after turning on. If this is the case, can someone confirm that this is a suitable replacement? (Intel Pentium E5700 Wolfdale 3.0 GHz LGA 775 65W Dual-Core processor desktop BX80571E5700http://www.Newegg.com/product/product.aspx?item=N82E16819116381

    If it's the motherboard (I hope not), it can be replaced without having to re - install windows? I can't find an exact replacement for the H - I41 - Μatx Foxconn (Eton). HP has one of these in stock that could be shipped out?

    I know that the computer is already out of warranty (barely) and can do the work myself, but need help to determine the problem I want to throw the money to do this work right.

    Thank you in advance for your help!

    John

    Hello jkalbin, I think a bad mother rather than the processor card. Chess with the processors don't happen often at all. You should never feed a computer with radiator/fan all not attached to the processor. Just 5 seconds without the radiator/fan could easily burn a processor.

    The fact that the processor had no hot does not mean it does not work, if the motherboard does not send power to the processor.

    Motherboard failures are many times more often than the failures of processor. I had one processor to fail in more than 25 years of working with computers.

    Just some thoughts.

  • HP Pavilion DV9888eo won't start with My Book Mirror 2 t connected

    Same problem here: http://h30434.www3.hp.com/psg/board/message?board.id=HardwareDPC&thread.id=4367

    Installation program:

    HP Pavilion DV9888eo, AMD Turion TL-60 x 2, 3 GB of RAM

    Western Digital My Book Mirror 1 t connected USB 2.0

    Windows 7 Edition Home Premium 64 bit (clean install)

    Problem:

    -Won't start if the external hard drive is connected to a USB port

    -Boot freezes, the BIOS detects the drive, shows USB 2.0: WD My Book, fan gets stronger

    Tried solution:

    -Different USB ports

    -Varied, boot order first set internal hd

    -Disconnect and start continues

    -Mouse USB wireless at the same time / plug, unplug, almost worked

    Works okey if hooked up later when Windows has loaded (also works just after when it is plugged in after successful BIOS).

    The closest match: http://www.experts-exchange.com/Storage/Hard_Drives/Q_23769717.html

    Any advice how to solve?

    Message edited by lukevader on 10/11/2009 16:02
    Message edited by lukevader on 11/11/2009 01:37
    Message edited by lukevader on 11/11/2009 01:48

    My conclusion: HP BIOS/USB controller isn't working okey with WD My Book when you start the computer. If you wait about 3-4 minutes, to return to the boot. If you re-create the partition in Windows 7, you might be able to speed up the process. I have converted the MBR to GPT (Google more) and reformatted it NTFS. Reducing a starter and holds a GPT formatted, cannot be a boot disk. Now, there are about 1 min delay. If there is a switch to turn off USB Legacy support, that could help. There is not, thanks to the crappy BIOS HP. You can also seek support from Western Digital and discover interesting things.

    Then, finally, it'll pass the boot.

  • HP Pavilion dv7 won't enter the BIOS. Anyone (Esc, F9, F10, F1, F2 etc.) on the key

    Hello

    I have HP pavilion dv7, which leaves me not in the BIOS to change the boot order.

    I have windows 8 32-bit installed and keep start normally any key (Esc, F9, F10, F1, F2 etc) at the beginning, is pressed or hold... it will not stop the boot and won't let me in the BIOS. All it does if the keys are pressed, it emits beeps but boot then anyway.

    I want to boot from USB and install WIndows 8.1 64bits.

    Help, please.

    Thank you

    This could help you as it solved my problem yesterday. I disabled quick start (or quick start) in the settings menu of your laptop. I have turned on one day, not knowing that it prevents you from all the boot options. I'm at work and do not have access to a large part of the internet, but google "disable fast boot windows 8 ' or 'disable' quickboot. There are quite a few Web pages that walk through it.

    I am now able to access BIOS.

  • HP Pavilion windows won't start

    Hello.. my computer hp Pavilion dv5 laptop starts and immediately after he says from windows will blackscreen with white cursor and hangs. When the computer starts the screen says dhcp... and in turn the line then nofilename or badfilename and when I did the test said some wild-card I think that the hobertkey all other tests, I ran seem to spend of the sections and the system restore won't let me... someone could help me please. Thank you for allowing me to post this... Robert... ps... my laptop is a hp Pavilion entertainment pc... SD.MS/Pro.MMC.xD...and windows 7 ultimate running sound

    Thanks Patnert... I installed windows 8, so I solved the problem... but certainly will use your suggestion in the future must be... I appreciate your time and your suggestion

  • Pavilion G6 WON'T START

    Can someone advise me. My HP Pavilion G6 1371 ea mobile gave me corrupt BIOS message (501) and the next reboot it froze at the close to the bottom of page for so long, I had to cut the power of it. Now ive tried to feed it upwards and I get nothing from it except a white light at the point of connection power as his charge only. I have removed the battery and connection and held down the power button / stop rhe and still get nothing. Not a fan of all start, nothing, except for the white light. I can't believe after being in this forum just how many people have encountered this same problem... seems to able to get an another im, im stuck with just this cannot so anyone please help so I can have it up and running again, please, but I have countless questions since getting this laptop...

    We wish you good luck and... Sorry I didn't be able to help.

  • HP Pavilion dv6000 won't start

    My laptop does not start. just replaced the battery thinking that might be the solution but it was'nt. When I press the button come from blue light on but nothing on the screen then the laptop turns off on its own or the lights will Flash several times then turns off? I hope that someone has encountered this problem before and has some type of solution. Thanks in advance for your help.

    Hello

    What to do if Windows does not start correctly
    http://Windows.Microsoft.com/en-US/Windows-Vista/What-to-do-if-Windows-wont-START-correctly#.

    Check with a real computer store (one that makes its own service internal and not of leeks)
    and displays a Best Buy or other stores) or system manufacturer support. Also
    Ask known problems in their forums.

    Support HP & drivers
    http://welcome.HP.com/country/us/en/support.html

    Contact HP
    http://welcome.HP.com/country/us/en/contact_us.html

    HP forums
    http://h30434.www3.HP.com/PSG/

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

Maybe you are looking for