Pavilion dm4-1075br: Test Battery ID failure

Similar Questions

• HP pavilion dm4: removing the battery / output switch problem

  MY hp dm4 Clubhouse has a switch relese battery does not move and so I can't remove the battery.

  What can I do to take out the battery?

  I was able to remove my battery, even if the trigger will not move

  I have read the documents under the next heading

  "Laptop battery seems to be stuck.

  He pointed out that my problem was very common

  BATTERY REMOVAL PROCEDURE

  As suggested-

  I inserted a piece of thin stiff plastic

  (for example on the size of a credit card but a little thinner)

  in the crack between the battery and the output switch

  I pushed the upper part of the plastic down

  and then I pushed up in the direction of the battery

  up until the crack of batttery widened to the point where I could use

  my nails in the battery of crack to pull the battery.

  I don't have to much force to make

  The angled battery to easily

  BATTERY INSERTION PROCEDURE

  As suggested-

  To avoid the problem of gel battery switch

  Move the latch of the battery in the middle of its sliding range

  When reinserting the battery first tilting the battery

  so that the side of the battery to the side of the computer case

  is first inserted into the battery compartment

  Then push down the other side of the battery in its compartment

  in the end, release the battery button while he spingngs to its normal resting position.

  I hope that this explanation is useful

• Adapter HP Pavilion dm4 battery/ac question

  I have a HP Pavilion dm4-3050 for about a year and a half now and lately, he keeps under its own stop without advising me how the battery percentage because normally, it tells me to plug it in when he reached 12%. Yesterday, I left him there, and it wouldn't turn on so I think it's batteries, so I plugged it and the battery light usually turns orange when he is in charge, but this time, it's white, saying: it is fully charged when it is 8% and it says plugged in, does not support. I did a race on the battery and it checks good. The laptop says that it is the main source is the AC adapter and not the battery. As soon as I unplug the power adapter, my laptop stops immediately. It works without the battery, but with the power adapter is plugged in. I don't know what's the problem with him.

  If it works fine without the battery just to power supply and the battery will not charge and it cuts when the AC adapter is removed, I have to suspect that the battery is bad although the battery test results.

• Pavilion dm4-3050us: replacement of battery HP Pavilion DM4-3050us

  My laptop battery is dead. Find the HP parts store replacement:

  593554 001

  Battery (primary) - 6-cell lithium-ion (Li-ion), 2.55Ah, 55Wh (MU06055).

  Original battery HP Spare part is 593554-001 but said 10,8 V - 55WT and 10.8 V - 5100maH.

  Why spare HP has 2550maH which is half of 5100maH?

  Help, please.

  Hello @Vlad478,

  Thank you for visiting the HP Forums! The Forums are a great place where you can find solutions for your problems, with the help of the community!

  I understand that you have a problem with the battery and wanted to help you!

  Based on the following guide, here are the compatible batteries for your laptop:

  HP Pavilion dm4 Entertainment PC - Maintenance and Service of Guide (Chapter 1, Page 4).

  ● 9-cell, 100-Wh, 3.00 - Ah, Li-ion battery

  ● 6-cell, 62-Wh, 2, 80 - Ah, Li-ion battery

  ● 6-cell, 55-Wh, 2, 55 - Ah, Li-ion battery

  It seems that you have replaced the battery with the lowest compatible option.  I hope this helps.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• I need to replace the battery of laptop for pavilion dm4-2180us

  I need to replace the battery of laptop for pavilion dm4-2180us

  Hello

  Copy the part from following link number:

  http://PartSurfer.HP.com/search.aspx?SearchText=QE374UA

  You can buy in the store or use part # buy elsewhere, such as:

  http://www.Amazon.com/593554-001-replacement-Notebook-battery-5200mAh/DP/B004MR2RMQ

  Concerning

• HP Pavilion dm4-3005 serious bug BIOS/drivers - ACPI.sys blocks constantly DPC to 3 milliseconds

  Some of our users reported problems with the HP Pavilion dm4, Intel i5, portable audio beats, so we bought such a system for the test, a HP Pavilion dm4-3005. The OS is Windows 7 Home Premium 64-bit.

  The questions were dropouts sound while using the software and USB audio interfaces that we do.

  Now, we have confirmed the questions and analyzed the cause behind it.

  The computer suffers from a DPC latency bottleneck, that fires continually in the OS ACPI.sys driver.

  ("CPD" is a regular work of pilots (Deferred Procedure Call).)

  Each DPC planned by each driver must always end quickly (less than 100 microseconds), or it causes a bug which acts as a bottleneck. When a long DPC runs in a driver, all other drivers are often necessarily suspended, for example, on a machine that behaves in the way reported, Windows can not reliable service all the drivers that need to run more often than once every 3-4 milliseconds.

  Low latency is necessary for all reception record, DAW, music app, software synth, as well as pro audio interface hardware drivers.

  Because of the congestion, they all suffer from heavy sound artifacts more use cases / underallocations for the pilot of the audio interface. This includes our products but also in any other software low latency and USB audio interfaces.

  HP Pavilion dm4-3005 has in this way from the factory, and no matter what drivers are disabled or set to date.
  I ran all the critical updates for installation of Windows 7 Home Premium 64-bit.

  I downloaded and installed all the updates driver from HP support.

  Finally, I also downloaded the BIOS update that available to HP support.

  I also followed several guides to address these issues, including advice prevailing to disable the driver "ACPI Compliant control method battery" in Device Manager (Edit: filled in the name of the pilot.)

  Does not the initial problem.

  I guess it's a bug in the BIOS - which has yet to be resolved by HP or their partner of BIOS for this product.

  I have the computer factory reset and ready for testing your solution, when it will be available.

  As it is now, we must warn our users of these systems because of their unusable latency.

  HP is aware of this problem?

  Thank you very much

  John Engstrom

  Developer

  Propellerhead Software

  Hello world

  I have good news for you, dm4-30xx users!

  The new BIOS is completed and will be published shortly by HP (need to package configuration file and write the documentation now...). The update of the BIOS version will be the F.0B.

  However, I have access to the "raw" version of this new BIOS. I can send it to you if you ask me, but in this case, you will assume any bad use of this file. In this case, please send me your mail by MP.

  The official release will not take much time, so I think it's best that you wait.

  Best regards!

• I have a HP pavilion DM4 M #1165dx

  my current internal Harddrive is maxed out 500 looking for a 2 GB to that has a life decent speed, found this on Amazon (Samsung Seagate tab portable disk HARD SATA III 2.5 inches of Bare dimm (ST2000LM003) internal drive) also have 4 GB RAM installed, I was wondering what would be the best route to level it so? Thinking 8-16 GB

  Hi @LoganHickman,

  Welcome to the HP Forum! I'm happy that you've become a member of the HP Forum. It's such a wonderful site to find answers and advice. Here is a link to guide you to what the most rewarding experience and answer questions about the display: first time here? Learn how to publish and more.

  I understand that your 500 GB HARD disk is full and you want to install a larger drive and more ram.  Here is a link to HP Pavilion dm4 Entertainment PC Maintenance and Service of Guide. Please note Chapter 3, page 24, section 15 modules of memory and point 18 drives for replacements recommended for your system. Please be aware that the maximum memory is 8 GB. (found in Chapter 1, page 2, memory). As a 2 TB drive has not been tested in this model, the result is unknown.  This does not mean that it will not work, only that it is not a walk recommended and not supported by HP.

  Please click on the "Twww.Mountainview.rsb.qc.ca Up ' below to thank me for my efforts! If my post has addressed your query, please click the "accept as Solution" while other people who may have the same query, can find the answer more effectively. Thank you for participating in Forums of HP!

• No HDMI audio on TV - Pavilion dm4-1160us Entertainment Notebook

  I know there are a lot of post on this issue, but nothing works for me.  I have a Pavilion dm4-1160us entertainment laptop running windows 7 64 bit.  I uninstalled the drivers both graphics and chip and reinstalled (warning says that I was installing was older than the one I had).  Maybe I'm not find the correct drivers to install. There is no audio device HDMI registered on the machine. AUDO devices listed are: IDT High Definition Audio CODEC for speakers and headphones.

  Hello

  My suggestion:

  • Go to this site to download the required driver.
  • Completely uninstall the Audio driver.
  • Install driver from the downloaded file.
  • Turn off the TV and the laptop.
  • Connect the HDMI cable.
  • Start by turning on the TV.
  • Turn on the laptop.

  Concerning

  PS many users have to do some testing and it turns ụp

• Pavilion dm4: cannot install windows on my laptop

  I had trouble installing a hard drive in my laptop.  The laptop is a Pavilion Dm4.  Below are the steps I've tried initially.

  1. insertion of my hard drive with Windows 7 installed and works very well in the Pavilion dm4.

  RESULT: computer crashed just after that the windows image came.

  2 reformat the hard disk by performing a clean install of Windows 7.

  RESULT: Once installation is complete my Windows installation fails and I get a message saying "Windows is unable to complete the installation. To install Windows on this computer, run the Setup again. »

  3 reinstall using the system recovery disk that I just bought HP using the code series of laptops.

  RESULT: After inserting the recovery disks and the driver installation disk, I get a message

  P2PP Burn Boot Check failed

  Possible causes

  1.yellow - bang occurred in Device Manager

  2. some silent-installation failure of applications

  3 Found failed to PININST_BBV

  4 Found failed to PININST_BBV2

  5 found memory dump file

  Suggestions:

  1. check REGDEV_BB. Drivers LOG

  2. check the BBApps. Application log

  3. check the memory dump file

  Hi @orangeg66,
  
  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!
  
  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dm4 Notebook and P2PP Burnboot could not install. I have seen that date back to 2012 first of all, and then by a default BIOS withthis document by selecting the reload the default BIOS settings. In this way, it will look at the hardware installed on your laptop. Restore factory default BIOS works on it.

  Note Remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.
  
  Please let me know how it goes.
  
  Thank you.

• Pavilion dm4-3090se: how to use the SSD after restoration of the system of Windows backup disks?

  Hello

  After a lot of work, I finally could restore my OS using Windows backup disks that I created a few years back. (The OS has been corrupted when the power has been accidentally deleted from the system and the battery was dead)

  Restoring backup widows put everything on 444 GB C drive.  Nothing I put on the SSD drive d:-20 GB and there is nothing in the tools of HP E: drive - 4 GB

  How can I make use of the SSD drive to help speed up the system?  I see the system starts and runs more slowly now.  I'm ready to blow the current operating system and re-run the Windows backup utility.  But I need to know how to use the SSD during the restoration.

  Any help is appreciated.

  Thank you

  Bob

  Hey @llebrez,
  
  Welcome to the Forums of HP Support! This is a great place to find solutions and help our community!

  I understand that you have some information about using the SSD in your HP Pavilion dm4 Beats Edition Entertainment Notebook. I'd be happy to help you with that.

  The SSD in your laptop is used for a technology called Intel Smart Response. Intel Smart Response uses the SSD as a type of Cache smart to help load the items faster. The reason why that is not used currently is because the restoration of the system is not designed to use the SSD for intelligent caching and is not able to establish that on its own.

  If you want to configure Intelligent caching on your laptop, you can follow this guide provided by overclock.net: how: implement the Intel Smart Response Technology (SSD caching)

  I hope this helps. If you have more questions that I'm able to answer for you, please do not hesitate to ask.

  Please hold me.

  By pressing the Thumbs Up button below, you can always say thank you!
  
  See you soon.

• HP Pavilion dm4-1024tx Enterta: upgrade to 8 GB of memory and is blue screen problem

  Product: HP Pavilion dm4-1024tx Entertainment Notebook PC
  Product number: XC651PA
   
  I have corsair Vengeance ram 8 GB (CMSX8GX3M1A1600C10) that as a result of the configurations as mentioned below:
   
  SPD 9-9-9-24 latency
  SPD speed 1333 Mhz
  SPD voltage 1.5V
  PC3-12800 (1600 MHz) memo speed
  Tested latency 10-10-10-27
  Tested 1600 Mhz speed
  Tested voltage 1.5V
   
  It passes the test of memory BIOS.
   
  BIOS VERSION: Hewlett-Packard F.27, 21/12/2011
   
   
  But when I boot windows 7, it shows the windows symbol and then it shows the blue screen with the error
   
  STOP: 0X0000007E
   
  If I replace memory corsair with the memory that has been delivered with the laptop the system only works very well.
   
  Corsair memory is not compatible with the system?
   
  I have a dual boot and installed ubuntu on this subject. Ubuntu loads perfectly fine, but after a while the system restarts automatically (IE open application).
   
  I tried memorytest86 to test the memory, but the application continue to crash and reboot and does not provide any results.
   
  Help, please.

  The RAM is not compatible. The system allows a maximum total memory of 8 GB and uses DDR3-1333 which downclocks at 1066 speed. You cannot use a single module of 8 GB. 4 gigs is the large single module supports the system. I suspect the memory that you have will work fine if you had modules of 2 x 4 GB instead of a single module of 8 GB. That's why memtest is not finished. The controller memory motherboard is not able to take up 8 GB of RAM by a single channel.

• white screen on pavilion dm4

  I have a pavilion dm4 and it does not start. I get a blank screen and led lights that blink 3 times on the caps lock button.

  I tried to take the battery and pressing the button and restart but does not work

  Windows 7 home is located on the computer

  Hello

  In this case, your best option is to contact HP by far and arrange for the laptop repaired under warranty.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Best regards

  DP - K

  

• Mousepad does not not Pavilion dm4

  Last night I woke up my computer to see that my mousepad not working. I thought it was some glitch like many others I've already found on this laptop (keys sound did not work properly, led light silent, not wanting to come away, etc.) And hope to restart and to solve the problem. Today, after the reboot, my mouse pad still does not work and I, apparently, am not the only one with this problem.

  My specs:

  HP Pavilion dm4-2070us

  Windows 7 Home Prem OA

  I tried updating the driver (he says that the version that was linked to the exact identical on my hard drive) and I also tried the update of the BIOS with the same result. The mouse pad IS NOT off. If it's light is no longer on this subject as well and it is stuck in stop mode. The mouse pad does not appear in the Control Panel, no matter what I do.

  I'm tired of all the problems that I've had so far on this laptop because I got it since mid-August. My friend told me that HP has been much better than Dell, so I went with it instead that little birdie told me. I was bragging to everyone how wonderful this computer was, but now I feel like I should go back and apologize to all my friends. Please say it is an easy fix and I forget something quite obvious. I wouldn't turn my back on HP for a computer laptop stupid.

  Currently, I solved the problem. If anyone has a similar problem to mine, before sending it in, maybe you can try what I did. Last night I let my computer choke completely then took out the battery for a few seconds. After that, I plugged and let it load a bit (maybe 30 minutes?) before trying to start it and try again the mouse pad. It works fine now, the zoom in/out and Ahmed seem to even work a bit better now.

• HP Pavilion dm4-1265dx: does not update HP Pavilion dm4-1265dx

  Pavilion dm4-1265dx has never successfully updated its software. I run the recommended updates that are included in my automatic Windows updates, but not the HP updates have already updated, it always says, "failed." I tried to update directly from the HP site and have experienced the same results. Any suggestions?

  Hello

  Thanks for posting your concern for the Forums for Support and sorry about the problem you are having. To help you the best I would need the failure error code. I will quote the steps to get the code of failure below.

  • Go to the Control Panel
  • Make sure that in the upper right corner of the ' view by ' is selected for both small or large icons instead of the category.
  • Go to "Windows update".
  • You will find on the left in the list 'view update history'.
  • In the list, the status of the various updates would b mentioned in the second column.
  • There will be updates failed, you need to right-click on it and click 'see details'.
  • On the next window, there will be "Error Details" section with code 8xxxxxxxx.

   

  These are the codes that are required. Please write us back with these codes. And also for resolved errors you can try to install the updates individually.

  • You have to go back to the control panel > windows updates.
  • In the list on the left choose "check for updates".
  • Once the updates is enabled, it will be little important and a few optional updates.
  • First click on the important updates and a list would be populated, choose the updates one by one.
  • After an update is installed and the le redemarrage reboot the PC, choose the second update and continue in the same manner.

  Although I work for HP, but I am personally.

  Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution. Click on the 'Bravo Thumbs Up' on the left to say 'Thank you' for helping!

  Concerning

  Aks3621

• HP Pavilion DM4-1165DX does not illuminate

  I have a laptop HP Pavilion DM4-1165DX.

  When you use yesterday, the screen flickered, and then the computer off. Now it will not turn back. When I press the power button, the led on the power button, button for on / off Wireless (F12), fingerprint and the light on the side of the portable flash player then return to offshore. There is nothing to indicate that the machine tries to start, just a flicker of lights, then back to nothing. These lights will also Flash when the laptop is plugged in, but not flashing unplugged the battery included.

  The light next to the power connector is on, indicating that the unit is powered.

  I tried a hard reset and that did not help. Does anyone have an idea what may be causing this problem?

  Thank you

  I talked to hp and they said that it is the motherboard... $351 for repair unless people start to complain, and he comes from a manufacturing problem... Be sure to report...