Pavilion dv6 7013 cl: about the computer hp laptop pavilion dv6 - 7013 cl/entertainment / it supports windows 10?

Similar Questions

• XC651PA: Change the RAM in the computer hp laptop

  I have a hp pavilion DM4-1024TX entertainment series laptop with 3 GB of ram built-in, but my pc has begun trolling due that I started thinking about the change/upgrade my Ram 8 GB capacity with Corsair 8 gb ram 1600 Mhz ddr3l 1.35v. My question is that my product page says I can go to 8 GB of DDR3 ram, so is there a difference between DDR3 and DDR3L

  Configuration?

  and is there a way I can speed up my system too.

  and in addition, my pc crashed a few months which resulted in my 500GB internal hard drive space to reduce to a minimum of 80-90 GB. Can I recover these lost too much space?

  Concerning

  Hello @Shaurya_mittal

  Here are the specs of your computer

  Link: http://h10032.www1.hp.com/ctg/Manual/c03106715

  page: 10 in the PDF Online.

  But also here.

  2 SODIMM slots

  Customer-accessible and scalable

  Supports up to 8 GB of memory system

  DDR3 memory, 1066 MHz, dual-channel (DDR3 1333 MHz demoted in DDR3 1066 MHz

  Supports the following configurations:

  8 GB (4 GB X 2)

  6 GB (2 GB X 2 + 4 GB + 1).

  4 GB (2 GB x 2 or 4 GBx1)

  3 GB (1 GB × 1 + 2 GB X 1)

  2 GB (2 x 1 GB) or 2 GB (1 GB x 2)

  1 GB (1 GB X 1)

  Hope this helps you.

  BR

• Unable to load up on my side of the administrator of the computer to load in safe mode but will not when windows loads any suggestions message cannot load profile

  When windows loads, I'm unable to load my side administrator, I get a message that does not load safe mode profile side administrator but will not load completely when in safe mode message cannot load all of the side admin suggestions am running Vista Basic

  Hi BillyM1948,

  (1) would you please provide the full error message that you receive?

  (2) remember to make changes to the computer before this problem?

  Step 1: You can follow the steps mentioned in the article below, which deals with a similar question

  Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.

  http://support.Microsoft.com/kb/947215

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756/

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Compaq Presario CQ56: a problem with the computer keyboard laptop presario CQ56

  All keys (F) Act as the FN key is been held down when it is not. This just started today. I have a free prog called "keyboard test utility. Now, I have discovered that I can get 1 clean tap of F4 and the prog to test keyboard shows only illuminated F4. The next time I hit the letter (P) F4 and the Windows key are lit. Now, if I tap the FN key, and then press the F4 key. Again, F4 is the only 1 who turned on the prog of test. It's almost like the FN button nosed. I just to confirm. Rather than hold down the FN key to get things under the keys (F) (as a volume-, volume +, cut and so on). Now, I have to hold down the FN key to get the regular F1 to F12 keys. The rest of the keyboard is fine. A regular toggle switch or a switch in a radio push button. The FN key acts like someone ripped the wires to the back of the switch and reverse the wires and the switch can operate in reverse. Beats me how this can happen to a laptop keyboard.

  Steve

  Hello

  Here are a couple of things to try.

  1. judgment of the laptop.  Disconnect the power adapter and remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f9 to load the default values (sometimes it is f5, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  2. try to change the default action of the keys 'f' as follows.

  Shut down the laptop.  Tap away at the esc you key start Notepad to open the Start Menu.  Select the Bios ( f10 ) option, and then change the figure in the document at the following link.

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c02035108 & DocLang = in & docLocale = en_US &...

  Kind regards

  DP - K

• to install xp sp3 on the computer hp laptop dv4 1318tu

  Hi all

  recently, I have a hp dv4series 1318tu notebook with vista preinstalled home premium basic with core 2duo trial, 4 GB of ram and 297 GB of hard drive. I tried many things to install xp sp3 on it and installed it (nlite) with the help of the thread with the link below. but the probleum his presist. After all my efforts sound does'nt installed. so I recovered using vista recovery disks.

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and/problem-in-Instlling-XP-in-HP-DV4-1318tu-series/m-p/126411

  So I decided to install xp as os double with vista. Sir I repuest know how to install xp sp3 (either using nlite or n - lite) and the legacy of this facility on the performance of the pc as the system will become slowly etc.

  I heard that if installing xp on vista preinstalled the i will have to manage the startup option using third-party software, as I don't have the vista installation disc; I have discs(3-DVD) of recovery.

  so, if I need to use any software for Startup Manager then please post a link to free software.

  I'll be oblized to the answer of the year...

  Ok.. Finally, after 3 days of my effort of aggrassive, I found the solution.

  required system:

  (1) windows vista recovery disk (can be downloaded from the following link)

  (2) easyBcd 2.0.2

  (3) Windows XP sp2 or higher and and nlite.

  Steps: -.

  (1) initially simply xp can'nt be installed. wake so this xp on a cd as shown on the following web:http://h30434.www3.hp.com/t5/Notebook-Operating-systems-and/Problem-in-Instlling-XP-in-HP-dv4-1318tu-series/m-p/126411

  (this step is for hp dv4 series laptop. I have the same.)

  (2) go to the following web page and learn how to reduce the disk to create a new partition for xp must be installed. and install xp (as shown) on the new partition. http://www.howtogeek.com/HOWTO/Windows-Vista/install-Windows-XP-on-your-pre-installed-Windows-Vista-computer/ now you have pc with xp and no option to boot from vista as vista bootloader is currupted.

  (2) go to the following web page and download windows vista recoverydisc. Download http://neosmart.net/dl.php?id=1 easybcd2.0.2 and install (note that easybcd does not work and gives an error). Copybootsect.exefrom the bin of easyBCD (where it is installed) and paste it into the recoverydisc of vista (downloaded above) > startup folder.

  (3) now to create a bootable disc of this updated (after gluing bootsect.exe) recovery disk. You can can create bootable USB drive. Goto http://torrentz.eu/ and download UltraISO > intall > select the vista (with added boosect.exe) recoverydisc the bottom > menubar > Bootable > write disk image and follow the instructions to create a pen yr starter drive.

  (4) now insert your bootable cd/USB with vista recovery disk > yu restart > device(cd/pendrive) yr to boot from to choose. > Click Next > fix your computer (not install now)> vista recoverydisc > select command prompt > type exactlyas follws byreplacing X with the letter by which your system assigns a boot media.

  Bootrec.exe /fixmbr x:\boot\bootsect.exe/nt60 all/force

  now restart your pcand it will boot with vista.

  (5) install easyBCD and goto edit menu start > select the drive letter from manually where xp is installed > add new entry. and reboot and you did.

• I can't find my dell dock after he disappeared (it was installed when I bought the computer dell laptop) HELP me please!

  I used to have a dell dock... now he's gone. I lost the front and found again, but I forgot how to find.

  Hi Nisha,

  Please see the thread below for options: http://answers.microsoft.com/en-us/windows/forum/windows_7-desktop/how-to-restore-the-dell-dock-toolbar/163e6840-bf50-4c49-bc2b-59a80bc7d30e

  Good luck!

  Kosh

• HP Pavilion 17-e113sm Notebook PC (G5F80EA) supports: Windows XP, 7, 8 operating systems?

  HP Pavilion 17-e113sm Notebook PC (G5F80EA) supports all 3 people: Windows XP, 7, 8?

  It comes without any OS (free BACK) installed and I want to know if I'll be able to install XP or 7 or 8 on it.

  Hello:

  SMBus: Downloand unzip and manually install the driver for smbus controller I have attached under attachments below.

  Go to Device Manager and click the controller smbus needing drivers.  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder that you unzipped.

  Make sure that the include subfolders is selected and the driver should install.  Then restart.

  Network controller:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131223-1&cc=us&DLC=en&LC=en&JumpID=reg_r1002_usen_c-001_title_r0004

  Bluetooth controller:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137961-1&cc=us&DLC=en&LC=en&JumpID=reg_r1002_usen_c-001_title_r0002

  For the unknown device, I would need in the first string of the hardware for this ID if this driver is not...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131788-1&cc=us&DLC=en&LC=en&OS=4158&product=7035454&sw_lang=

• Blu - ray disc will not play with Windows 7 installed on the computer hp laptop pavilion g6

  Although the non - Blu Ray discs play fine on my HP Pavilion laptop with Windows 7, discs Blu Ray will not be. How a computer model does this work?

  Hi, John:

  It's the hard drive.

  You need to go to Device Manager, and then click to expand the category of DC/DVD player.

  If the name of the dvd player does not have a BD in the model, it is just a standard dvd player and cannot play blue ray discs.

• Recovery Windows 7 64-bit on the computer hp laptop pavilion g6.

  Hi all!

  My laptop: HP pavilion 1b79dx g6.

  OS: Windows 7 64-bit edition Home premium.

  In December, I've updated Windows and restart automatically. Then I wait for update of Windows, but through system 1 hour not working and I turned off laptop. Then I switched on the laptop and after that login and password computer laptop cannot open Windows. I try: esc, f8, f9. F10, f11, but hp Recovery Manager does not work. I can start Windows in safe mode only. I try to start recovery manager (HP and Windows), both not working. I see: Recovery Manager hp stopped work. I try chkdsk from command prompt, it did not help me. D: partition is normally. 2 times I can open windows is normal, but then nothing does not, only I see my old office. What should I do for normal work of Windows?

  Thanks for any help.

  You need perform a recovery.  There are several methods to do this and the document that I am linking to, will provide the steps.

  I hope this helps.

• Pavilion g6: 2 left usb port of the computer hp laptop pavilion g6 does not

  2 left usb port are not work ing after 7 (64 bit) laptops.windows formatting has loaded.two usb ports on left side doesnot answer

  Hello:

  You probably have to install the applicable usb3 driver.

  What is the complete model number or the product number of your computer laptop g6?

  Many products are on the label as well as the serial number.

• Phone scams about the computer.

  I got a phone call from "John Davis" with a strong accent told me that he works for a company called "Key PC Doctor.com" and my computer referred all sorts of viruses, etc.. He said that I should open the dialog box run on my computer and type in 'event vwr '. Looked like a scam any for me, then, of course, that I don't have. Is it really a scam?

  Yes, it's a scam.
   
  It's a real call from Microsoft?
  http://www.ComputerActive.co.UK/CA/PC-help/2134917/genuine-Microsoft 
   
   

• is there any replacement of the computer motherboard laptop dv5 pavilion?

  I have a pavilion dv5 laptop. My father bought in the United States. but I've only used for 3 months. When I sent it to a technician, they told me that my laptop is already irreparable due to problem of Council. I don't know what that means. is there any replacement motherboard or is there a chance for my laptop be fixed.

  Hello

  Please visit the page #92 this book to get the right one.

  h10032.www1.HP.com/CTG/manual/c01550108.PDF

  Kind regards.

• question about my computer motherboard laptop dv6-7213nr of HP ENVY

  Hello all I'm new here but I have been using computers laptops hp for the years and love

  anyway I was doing research on my motherboard for laptop and I came across something interesting, but it confuses me also from what I can tell that the CPU is soldered to the Commission which sucks I wish I put the cpu to an a10 to make quick lol

  But what caught my attention is there are a grip also on the card that says cpu2 beside it, can someone explain this than her for please

  Thank you

  I need a picture. The CPU on a dv6-7000 is not welded to the card. This is the reference number of the Council:

  682180 501

  Here are the Board of Directors:

  

  Where the CPU2? The big white thing holds the CPU and you could install this:

  AMD A10 - 4600M 3.20 GHz processor (FSB 1600 MHz, 4: 0 - MB L2 cache, DDR3,
  quadruple - heart, 35 W) 683046-001

• I'm about to computer cover laptop MSI remove with the handshake...

  .. .and it open so that I can get dust that needs to be there because it is overheating. It's way past warranty, so there is no problem to break the warranty sticker. I've read up on the Internet on the question and would really like to know if static electricity is really the big deal that of some people argue that it is and if it is essential to guard against it all rummaging through the bowels of the laptop.

  http://www.YouTube.com/watch?v=MamAeWfHcrs shows the disassembly of the unit (it seems that the cr600/500 are similar). You're lucky if this video is correct because it shows that the fan is removed through the basic coverage.

  Just follow the video at 01:34, as it's the bit that you need to clean. Because you have to disturb the heat plates are becoming a new sink compound. The bits that are actually held by screws with the passing copper pipe by should have a gray grease like coating under and on top the songs they cover. This should be renewed.

  After getting that part you need to separate the fan and the radiator to improve air flow. The mat which accumulates can be quite dense and difficult to just blow.

• The computer upgrade laptop RAM

  Hi, I've had my HP Pavilion m6 1006tx for about 11 months now and I had success in the basic forms of games (minecraft and other training games not so much). Now, my computer has an Intel core i7-3612QM multi-core cpu clocked @ 2.1 ghz with intel boost 3.1 as well as 2 GB RAM graphics card dedicated AMD 7670. But I'm here to talk about upgrading my RAM, I noticed that 4 GB of RAM does not allow me to run a lot and all-in-all barely able to run a game requiring a minimum 2 GB of RAM, so I would like to know if I would cancel my warranty if I upgraded my RAM.

  I also want to know if the RAM as the dicksmith (http://www.dicksmith.com.au/computer-accessories/dse-8gb-ddr3-1600mhz-nbook-ram-dsau-xm5717) would work with my laptop current RAM which comes with the laptop, as in can I use RAM of two different brands, first and second, can I used two different amounts of RAM at any given time?

  Thanks for the reply if you do. Also if you need all the most characteristic, or do not understand anythings please indicate so and I will clarify with you details

  My apologies, just need to really read it, I just read the forums main post with the upgrade and other things, I tried to look before and it has not loaded so I posted this but it's working now, sorry guys