Pavilion dv6636 stuck in a reboot loop with no boot

Similar Questions

• Computer is stuck in a reboot loop, while security updats

  ORIGINAL TITLE: reboot problem

  Computer is stuck in a reboot loop, while security updats

  Hello

  1 were there any hardware or software changes made on the computer before this problem?

  2. do you get an error message or an error code? If Yes, what is the exact full error message?

  I would suggest trying the following methods and check if it helps.

  Method 1: Try to run the system in safe mode restore.

  Step 1:
  Try to start the computer in safe mode, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:
  Once you start the computer in safe mode, try to perform the system restore and check that if it helps, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  If you were able to start your computer normally by using the system restore, then refer to the following method, and try to update your windows.

  Method 2: To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

  Note: follow step 7 to reset the computer to start as usual after the boot process.

  http://support.Microsoft.com/kb/929135

  See the following help link.

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-installing-updates

  Hope this information helps.

• Reference Dell Vista stuck in a reboot loop must restore

  I have a dell desktop computer I bought from rent a Center about 2 years ago. It comes with Windows Vista. They don't did me not a recovery disk. I had a lot of questions and restore points were not helping, so I went through f8 and fact a reset. After that she completed successfully I clicked on finish, and it began to restart, which I expected.

  Now, however, he is stuck in a reboot loop. It gets to the screen that has Dell on this, with the f2, f12 options in the right corner, and then start again again and again. I tried to press f8 and hope go in safe mode and see what was up, but f8 does not open and f2 and f12 are not help at this point. they give me boot priority and so on but no real start until now kind of options. It is possible that windows doesn't have factory loaded, and now I have simply no operating system?  They say they have a reset disk can I come down and use, but im wondering if this will help because I can't really get anywhere or if im just done...

  No messages online that I was looking for really specific my situation...

  * original title - Dell Vista Start Up start up loop *.

  Hello

  ·         Did you follow the steps in this article to restore the computer to factory settings?

  If a factory restore full does not lead to a fully functional version of Windows then you have a hardware problem. I came in contact with Dell technical support.

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP Windows 7 stuck in a reboot loop

  Hi all

  Recently, I accidentally upgraded my HP Envy 14 from Windows 7 to Windows 10 and let the month pass without switch back.  Due to one host of other problems that have arisen, I decided to Windows 7, so I took out my old Windows 7 recovery disc to re-install Windows 7.

  He successfully reformats the hard drive and everything seems to go well until the end of the installation, when all of a sudden it shuts off and restarts.  He will then get as far as the 'starting windows' screen before it restarts again, each time giving to the screen "Windows is not stopped successfully", is not just a part of the installation process.  He's stuck in this reboot loop.

  Any advice?

  Couple comments:

  I have created a startup repair disk and ran the Startup Repair, but he reported having found no problem.  Very well.

  When you try to start the computer in safe mode, I get to the screen "Windows is set up your computer for first use" and then informs me that Windows cannot complete the installation in safe mode.  He gets up to now in normal mode, however.

  The battery is thus burned - can install Windows on a computer that has failed the test of the battery?  I don't see how there would be a relationship, but I'm really running out of ideas.

  Thanks for any help/insight you have!

  Eventually the recovery disc files are corrupted, try the following:

  Download Windows 7:

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

• I have installed winxp sp3 on the Intel computer, at first that my computer is stuck in a reboot loop

  At first my computer intel was blocked in a reboot loop, then just the black screen with cursor.

  I could never establish safe mode! I don't have a recovery partition.

  Hello

  Step 1: You can try using disable automatic restart on system failure option and check if you get the error message. If you get one, then return the exact error message.

  a. restart the computer.

  (b) that the computer restarts, press the F8 key repeatedly until you see the Windows Advanced Options screen.

  c. use the arrow keys to select disable automatic system error rebootand press ENTER.

  Step 2: Reinstall Windows XP.

• Laptop stuck in a reboot loop

  Original title: locked cpu

  my computer laptop gateway is in a continuous reboot loop at startup.vista family premium is the operating system, automatic restore or restore to an earlier point in time not working, what a Dick I do?

  Hi Ohmer,

  1 did you recent hardware or changes to the software of the system?

  2. you receive messages or error codes?

  You can try to disable restart of the automactic on the failure of the system and look for the error.

  For more information, you can consult the following article:

  Startup options (including safe mode)

  You can also try the following steps and check if it helps.

  Method 1:

  You can try to perform a test of the last good known Configuration and check if helps solve the problem.

  Using the last good known Configuration

  Method 2:

  You can also check if the problem occurs in safe mode.

  Start your computer in safe mode

  Method 3:

  If the problem occurs in safe mode, and then try to perform a startup repair and check if it helps.

  What are the system recovery options in Windows Vista?

• XP is stuck in a reboot loop, cannot use the option to repair with the XP installation CD

  have you tried disturbances on xp installation cd gives just exit and restart option

  * original title - xp keeps rebooting after screen with xp color logo *.

  I had not so long ago.  You can start your PC in safe mode using the F8 key on startup?  So then start in safe mode go to your add/remove software in the control panel and delete all of your drivers.  Mine was a the driver conflict.  Once I removed all my drivers, the system starts fine and then reinstalled the appropriate drivers based on DLLs installed previously.

• Windows Update problem! Now it is stuck in a reboot loop!

  I have Windows Vista on a Dell Latitude D620. Today I did a
  Download of updates and it went through the shutdown procedure and restart the computer. Now it is stuck on "Configuring Updates - part 3 of 3 0 0% complete.". There is disk activity, then it restarts, only to return to the exact same page.

  I tried every safe mode, last known good config, etc., but as soon as it starts it goes to this screen. I can't get to a prompt... nada... It comes
  driving me crazy. Even the guy I talked to at Dell do not know which increased or how to fix it.

  Help, please?

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your falls into the above category: download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• HP pavilion g6 stuck on the black screen with cursor 8 windows

  Hello.

  I used windows 8 perfectly... but today when I rebooted my laptop I don't have the 'Press esc to access the configuration menu"and once loaded in the windows icon. It got stuck on the black screen...

  Any ideas or suggestions? How can we get? Icannot go to the start menu cannot load the... Task Manager what can I do? Also the battery also affects bones

  "It was a moment cartoonic, when gravity stops for coyote to make him realize that he was wrong from the beginning."

  Hi, I did a hard job looking for a solution, and after a while, I found a solution. The solution to the problem was a little easy, but at the same time a bit funny too, hehehe.

  The solution was, when I removed the battery, then did what you told me, I even! Even the black of the same screen cursor. Then I tried power the computer nothing do but simply by pressing the power button without the battery in it. The laptop ran using cable ca, and then I was able to use the windows. Its perfect work. Now I have piles in too and its still in good condition.

  Now what do me? Should I replace the battery, I get error 601 (main battery) too. So should I replace it with a new one? I hope that it will be more preferable.

• PC crashed and got stuck in a reboot loop

  Hello, we have a Dell Inspiron 531, and this morning, he had a big crash and then got stuck in a boot loop, blue screen and trying to fix the system. My OH stop it manually. The only change made to the computer of yesterday has been an update to iTunes.

  I just tried to start safe mode and he just tried to restart again and showed a blue screen with a stop error message - I think as a 000000008.  I tried startup repair and he attempted repairs for a few minutes and has now arrived to the top with a message "Startup Repair cannot repair this computer automatically. Here are the details:
  Signature of the problem:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  02: 6.0.6000.16386.6.0.6001.18000
  03: 6
  04: 131074
  05: 0x8e
  06: 0x8e
  07: 0
  08: 2
  09: WrpRepair
  10: 0
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033
  Then, there was a message saying remove all devices that have been recently joined. But it is not all delete.
  Some background info-

  There was a problem with the graphics card driver, causing a blue screen (code 116) shortly after the start to the top. In summer, we opened the folder and emptied all the dust, and he stopped the problem. However, he's back. I bought another graphics card, but have not had the opportunity to install again.

  There is also a problem with Windows Update. He has mysteriously stopped working in mid-October.  He attempted to verify updates and then gives an error code 80070005. I started to try to solve this problem a few weeks ago looking for malware. A scan with Kaspersky Internet Security found nothing, but when I run the Microsoft Safety Scanner it finds three feats of Java. He eliminated two and partially removed the other. I always try to get rid completely of partially removed but did not have a lot of time this week to look at it, and the computer seems to be working ok otherwise.

  I also had problems trying to update Adobe Reader recently (' error writing to the file C:\Config...) Make sure you have access to this directory").  I don't know if these things are connected. But thought it would be better to talk about.

  Thank you very much in advance for your help.

  Hello

  The error code indicates that the drive is defective and must be replaced.

  You will be able to connect the drive to another computer or you may use a live cd to backup their data on an external drive.

  Hope this information helps.

• After installation of updates, received the critical error, then stuck in a reboot loop, Windows Defender now firewall and Security Center are all off

  I recently downloaded updates from microsoft. One of them was Security Essentials. Well, when I did caused a critical error. My laptop shut down and restarted. then gave me the same error message and rebooted again. He kept in a continuous loop. I tried the system recovery, but that did not work. I managed to get him to stop, but now my firewall is disabled and the Security Center and Windows Defender. If I try to turn it on, it does the same thing again. I don't know what to do to solve this problem. I need help!

  Original title: critical error

  Hello

  1. you have any multiple security software installed in the computer?
   
  2. What is the exact error message?
   
  Please follow the links below to solve the problem.
   
  Method 1
   
  Step 1
   
  Disable all third-party antivirus programs
  
  To disable a firewall, antispyware or antivirus program, right click on the appropriate icon for the firewall, anti-spyware or anti-virus program in the notification area in the taskbar. Then, click exit or click disable.
   

  a. in Windows Vista, click on start toreduce this includes this image, type appwiz.cpl in the Start Search box and press ENTER.

  b. in the list of installed programs, search for and then click on the program in question, and then click Remove.

  c. restart the computer.

  Note After you uninstall a third-party antivirus software, contact the manufacturer of the program or visit the company's Web site to see if a cleaning tool is available to help you remove any remaining files.

  Step 2

  See services

  a. click on start

  b. type services.msc

  c. navigate to the Windows event controller (right click on and select properties)

  d. set the startup type to automatic, start the service, click on apply and OK

  e to navigate to the Base filtering engine (right click on and select properties).

  f. set the startup type to automatic, start the service, click on apply and OK

  g. navigate to 'Windows Firewall' and select Properties (right click on and select properties)

  h. set the startup type to automatic, start the service, click on apply and OK

  Method 2

  Start your computer in a clean boot to avoid conflicts with third-party software.
  
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135
  
  Note: follow step 7 of the article mentioned above to start the computer in normal startup, once you have completed the necessary troubleshooting.

  Method 3
   
  Look for errors in the event viewer.
   
  Please check the Event Viewer logs to find errors in application logs.
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  
  Please post the results for a better understanding of the problem causing the reboot.
   
  Hope this helps

• Stuck in a reboot loop trying to upgrade to windows 10

  I think I downloaded the free update to windows 10 of my windows 7 ultimate. Windows update, it says my windows 10 upgrade is ready, and I have to restart my pc to start installation. I click the icon of the computer to restart, it restarts my computer, then the message again the same. I shut down the computer and restarted with the same result. Help?

  Download Windows 10:

  How to download official Windows 10 ISO files

  Boot from the bootable copy then do a custom installation:

  How to: perform a customized Windows installation

  then

  Recover personal files from the Windows.old folder, such as pictures of Documents and Windows Live Mail emails in Windows 10

• Palm TX stuck in a reboot loop

  I have a Palm TX which is a little over a year old. It was not subject to any negligence, to the best of my knowledge. This morning the battery was dead and so I put on the charger. 10 hours or so later, when it was activated, he showed the first 2 logos of start-up and then repeated again and again. The power button does not turn off the PDA and I tried both a soft and warm, reset without success. Need help please

  Message edited by Bob_L on 10/16/2008 20:49

  You have all 3rd party programs installed on the TX? These can sometimes cause looping.

  If you have no 3rd party programs, you should try the hard reset. The hard reset will erase all data on the TX.

  Go to http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=887 and follow the directions to do a hard reset. Then before of you hotsync your data back you will need to rename your backup folder, to do than go here.

  XP
  C:\Program files\palm or palm one\ [hotsync username]------and rename your backup
  file Backup.Old

  Vista
  Start--> documents\Palm OS Desktop\ [hotsync username]------and rename your backup
  file Backup.Old

  Then hotsync from your current name of hotsync and all your contacts, calendar,
  tasks and memos coming back.

  Show the file extensions for XP or Vista

  XP
  If you cannot view the extensions of file on your PC I would you open a
  folder, go to Tools--> Folder Options--> View (tab) and under Show hidden
  files and folders to uncheck Hide extensions of known file types.

  Vista
  Open control Panel, go to--> View (tab) and under show hidden folder Options
  files and folders to uncheck Hide extensions of known file types.

  Message relates to: Palm i705

• Updates auto, stuck in a reboot loop

  original title: Auto updates

  My 4 computers at work have auto update, but he keeps asking me to restart even if I already have several times. Any advise?

  Some basic steps you can try to do is: http://support.microsoft.com/kb/947821

  or http://support.microsoft.com/kb/929833

• Stucks L50 - A satellite in reboot loop

  My L50 - A Satellite is stuck in a reboot loop. I put the computer off and drained the battery.

  Whenever I have it plug in I see the opening screen Toshiba (with no invitation to press F2 to pass set up) then it goes back to the reboot screen.

  I tried via a recovery bootable on USB but t does not work.

  What is there to do?

  > I tried to use on a USB key bootable recovery but t does not work.

  I assume you tried to reinstall the original recovery image. It should work.

  Enter the BIOS and set it to default settings. After that restart your computer and press F12. Choose the USB device as the boot device and try to restart recovery image installation.