Pavilion g102: adding memory access

Similar Questions

• Glued on Pavilion g7-1329wm memory access cover on?

  The memory on my renovated Pavilion g7-1329wm access cover seems to be stuck on. is this normal?  The two setscrews are relaxed, but the cover is firmly in place.  Am I'll break the cover if I try to remove more that I'm already scared. Suggestions?

  Hello:

  It is not glued down and it is very difficult to remove. Just be careful and raise nearly all of the tabs.

  See this post... next to the last entry and related links I posted (post shaded green).

  http://h30434.www3.HP.com/T5/notebook-hardware/Pavilion-G7-1150us-accessing-memory/m-p/1578347#M73644

  Paul

• Pavilion g7-1150us - memory access

  I can't figure out how to down the access HD/memory Panel.  I removed the two screws (obvious) and took the battery, but it still does not move.  What Miss me?

  Hello:

  Please read the thread below and the links I posted, and you should be able to get the case open.

  http://h30434.www3.HP.com/T5/hardware-upgrades-replacements/HP-Pavillion-G6-memory-upgrade-problems/m-p/1374715#M6863

  Paul

• wrong time and date in the hp Pavilion a305w pc after adding memory

  I took the tour of the hp Pavilion a305W (Windows XP) PC to a place where they have added memory because it was very slow.

  After that, it would not start by itself, and the Date and time are not good.

  Thanks for your help.

  Hello

  Very probably during the process of adding more memory you may disrupt the battery CMOS (or RTC) or even the chip for the BIOS itself. Please (no need to do this):

  • Reinstall the components autour RAM slots
  • Change new battery for RTC
  • Check the BIOS and reset the date hour away
  • Check the date and time of Windows.

  Kind regards.

• Reading binary Dump using the DMA (Direct Memory Access)

  Hi all

  We are trying to measure short-term frequency using the SR620 (frequency meter) via a GPIB-USB connector. We are trying to understand how to work the controls GPIB, and it seems that you normally send a query and then ask him to read what says the instrument. However, as we try to make a measure of frequency stability in the short term, we use the binary Dump command (BDMP - explained in the manual, link below). To read this data, you do not use the standard playback function, you use this process called base (DMA, Direct Memory Access). The maual speaks DMA and the example code in the maual seems to use DMA to read the data that results.

  We have been able to trigger the display of "binary output" on the instrument using LabVIEW and interactive control via the NOT-MAX. The question now is: How do we implement DMA by using LabVIEW? More specifically, how we implement DMA reading of the SR620. It doesn't seem to be anything close to it in the code of LabVEIW included. There are examples that use the DMA with IVIs, but we had difficulties to change to work with the SR620 code.

  Useful links:

  Manual for SR620: http://www.thinksrs.com/downloads/PDFs/Manuals/SR620m.pdf

  Possible example DMA? : https://decibel.ni.com/content/docs/DOC-9893

  DMA explination: http://zone.ni.com/reference/en-XX/help/371599J-01/lvfpgaconcepts/fpga_dma_how_it_works/

  How to make DMA: http://www.ni.com/white-paper/4534/en/

  Note: When we did not step 1 passed because we have problems adding a new target of the FPBA, because there is "".

  Yes, in ' 89, you probably use a DMA to store the data fast enough.  In 25 years, things have become much faster.  What I did to somehting similar is to save the data to a file as it is being read.  If you want more performance, use a producer/consumer.

  

• WebLogic crash after error 'illegal memory access.

  Hi all. WebLogic application crashed after receiving an illegal memory access error. any thoughts...
  
  Error message: illegal memory access. [54]
  Signal information: si_signo = 11, si_code = 2 si_addr = 0xb5778850
  Version: BEA JRockit (R) R27.4.0-90_CR358515-94243-1.5.0_12-20080118-1154-l
  Linux-ia32
  
  
  The Weblogic administration Console does not start since the accident of Jrockit. I have attached the startup log failed.
  
  < 8 January 2009 11:13:22 AM MDT > < critical > < WebLogicServer > < BEA-000386 > < server subsystem failed. Reason: java.la
  NG. ClassFormatError: com/bea/xbean/store/Xobj$ DocumentXobj: invalid LineNumberTable 27684 pc
  java.lang.ClassFormatError: com/bea/xbean/store/Xobj$ DocumentXobj: invalid LineNumberTable 27684 pc
  
  
  
  Journal of weblogic admin stdout:
  
  Java home = / ps_opt/wl92/jrockit_150_12
  Ligne de commande java = java - jrockit-Xms256m-Xmx256m-Dweblogic.Chunksize=65536-Djava.util.logging.config.file=/ps_opt/wl92/webserv/myserver/applications/peoplesoft/logging.properties-Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger-Dweblogic.Name=WebLogicAdmin-Dps_vault = / ps_opt/wl92/webserv/monserveur/psvault-Djavax.net.ssl.trustStore=/ps_opt/wl92/webserv/myserver/keystore/pskey-Dweblogic.ProductionModeEnabled=true-Djava.security.policy=/ps_opt/wl92/weblogic92/server/lib/weblogic.policy-Dssl.debug=false-Dps_home = / ps_opt/wl92 weblogic. Server
  Options Java jrockit =-Xms256m-Xmx256m - Dweblogic.Chunksize = 65536
  < 8 January 2009 11:13:20 AM MDT > < opinion > < WebLogicServer > < BEA-000395 > < according to the contents of the extensions added at the end of the classpath directory:
  /ps_opt/wl92/weblogic92/platform/lib/p13n/p13n-schemas.jar:/ps_opt/wl92/weblogic92/platform/lib/p13n/p13n_common.jar:/ps_opt/wl92/weblogic92/platform/lib/p13n/p13n_system.jar:/ps_opt/wl92/weblogic92/platform/lib/wlp/netuix_common.jar:/ps_opt/wl92/weblogic92/platform/lib/wlp/netuix_schemas.jar:/ps_opt/wl92/weblogic92/platform/lib/wlp/netuix_system.jar:/ps_opt/wl92/weblogic92/platform/lib/wlp/wsrp-common.jar:/ps_opt/wl92/webserv/myserver/lib/endorsed/xalan.jar:/ps_opt/wl92/webserv/myserver/lib/pluto-1.0.1.jar:/ps_opt/wl92/webserv/ MyServer/lib/portlet-API-1.0.jar:/ps_opt/wl92/webserv/MyServer/lib/ps_patch.jar >
  < 8 January 2009 11:13:21 AM MDT > < Info > < WebLogicServer > < BEA-000377 > < start WebLogic Server with BEA JRockit (R) Version R27.4.0-90_CR358515-94243-1.5.0_12-20080118-1154-linux-ia32 of BEA Systems, Inc. >
  < 8 January 2009 11:13:22 AM MDT > < critical > < WebLogicServer > < BEA-000386 > < server subsystem failed. Reason: java.lang.ClassFormatError:
  com/bea/xbean/store/Xobj$ DocumentXobj: invalid LineNumberTable 27684 pc
  java.lang.ClassFormatError: com/bea/xbean/store/Xobj$ DocumentXobj: invalid LineNumberTable 27684 pc
  at java.lang.ClassLoader.defineClass1 (Native Method)
  at java.lang.ClassLoader.defineClass(ClassLoader.java:620)
  at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124)
  at java.net.URLClassLoader.defineClass(URLClassLoader.java:260)
  in java.net.URLClassLoader.access$ 100 (URLClassLoader.java:56)
  in java.net.URLClassLoader$ 1.run(URLClassLoader.java:195)
  at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
  at java.lang.ClassLoader.loadClass(ClassLoader.java:306)
  to Sun.misc.Launcher$appclassloader$ AppClassLoader.loadClass (Launcher.java:268)
  at java.lang.ClassLoader.loadClass(ClassLoader.java:251)
  at java.lang.ClassLoader.defineClass1 (Native Method)
  at java.lang.ClassLoader.defineClass(ClassLoader.java:620)
  at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124)
  at java.net.URLClassLoader.defineClass(URLClassLoader.java:260)
  in java.net.URLClassLoader.access$ 100 (URLClassLoader.java:56)
  in java.net.URLClassLoader$ 1.run(URLClassLoader.java:195)
  at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
  at java.lang.ClassLoader.loadClass(ClassLoader.java:306)
  to Sun.misc.Launcher$appclassloader$ AppClassLoader.loadClass (Launcher.java:268)
  at java.lang.ClassLoader.loadClass(ClassLoader.java:251)
  to com.bea.xbean.store.Cur$ Locations. < clinit > (Cur.java:482)
  to com.bea.xbean.store.Locale. < init > (local .java: 168)
  at com.bea.xbean.store.Locale.getLocale(Locale.java:235)
  >
  < 8 January 2009 11:13:22 AM MDT > < opinion > < WebLogicServer > < BEA-000365 > < changed failed State Server >
  < 8 January 2009 11:13:22 AM MDT > < error > < WebLogicServer > < BEA-000383 > < is not an essential service. The server will shut down >
  < 8 January 2009 11:13:22 AM MDT > < opinion > < WebLogicServer > < BEA-000365 > < server status changed to FORCE_SHUTTING_DOWN >

  Hi Nicolas.

  Is this patch for Weblogic 9.2? 92MP3 no patches
  Is what version of Peopletools? 849.09
  What OS? Linux 2.6.9 - 67.0.20.ELsmp
  He broke down at the start? Yes, it will fail when trying to start the administration server

  Let me know thanks

• adding memory cards

  Hello

  I want to improve my iMac, by adding memory cards.

  My problem is not sure about the maximum limit of memory can I add I m.

  Can you tell me if it's 32 GB or 16 GB or 12 GB?

  Each location must have the same value or if we can mix different sizes of memory?

  How is the maximum that iMac 11.3 with i7 processor supports? 32 GB, 16 GB or 12 GB?

  Thank you very much!

  Mariana

  System details:

  Model name: iMac

  Model identifier: iMac11, 3

  Processor name: Intel Core i7

  Processor speed: 2.93 GHz

  Number of processors: 1

  Total number of Cores: 4

  (By heart) L2 cache: 256 KB

  L3 Cache: 8 MB

  Memory: 4 GB

  Processor speed of interconnection: 4.8 GT/s

  Boot ROM version: IM112.0057.B00

  Version of the SCM (System): 1.59f2

  BANK 0/DIMM0:

  Size: 2 GB

  Type: DDR3

  Speed: 1333 MHz

  Status: OK

  Manufacturer: 0x80CE

  Part No.: 0x4D34373142353637334648302D4348392020

  Serial number: 0x792C8110

  BANK 1/DIMM0:

  Size: 2 GB

  Type: DDR3

  Speed: 1333 MHz

  Status: OK

  Manufacturer: 0x80CE

  Part No.: 0x4D34373142353637334648302D4348392020

  Serial number: 0x792C8112

  BANK 0/DIMM1:

  Vacuum

  BANK 1/DIMM1:

  Vacuum

  go to http://www.crucial.com/ basics and put in your mac details and they will show the compatible modules and configurations

• I have a HP Pavilion A6700Y. Currently, access to internet by modem. Want to go wireless and use

  I have a HP Pavilion A6700Y.  Currently, access to internet by modem.  Want to use the Wi - Fi and wireless.  Any ideas on how to do it with this computer.  If so, what would take?

  cmm0822bam wrote:
  

  I have a HP Pavilion A6700Y.  Currently, access to internet by modem.  Want to use the Wi - Fi and wireless.  Any ideas on how to do it with this computer.  If so, what would take?

  What type of modem do you have?

  Do you hear an old style phone modem or a cable modem?

  If you have a cable modem and it is not wireless, then you'll need to buy a modem wireless also has four LAN ports. Connect the WAN port on the router to the modem that provides your internet connection and then configure the SSID of the router and the wireless PC network card.  The easiest to install and configure is brands like Linksys and Netgear. Your PC with a built-in B/G wireless network adapter. Purchase of a high-tech Wireless-N Dual band Router router would be too much serious.

  Best regards

  ERICO

• am adding memory when I remove the battery I have to pay in order to get the full charge of her

  am adding memory when I remove the battery I have to pay in order to get the full charge of her

  N ° but see:

  About the batteries in the modern Apple laptops

  Battery Universityy

  Apple laptops - batteries-

  Apple - Batteries

  Extending the life of your laptop battery

  MacBook and MacBook Pro-Mac reduced the speed of the processor when the battery is removed when using an adapter A - C

  Apple laptops-calibrate the battery in your computer for optimal performance

  County of Mac Laptops-determining battery cycle

• Envy 15 360 t: adding memory

  I'm considering buying a want, it comes with 8 GB. Video AT hp and DOCS say I must go from the top, remove everything to memory.
  
  Is this correct? I have sort of the bottom. There is no access panel.
  
  Help please.

  Your Service Manual:

  link to the manual

  See page 49. Memory access involves almost complete disassembly, including removal of the motherboard. It should also threaten security that HP will not void the warranty if done successfully.  Access is from the top down. The hood is removed first.

  8 concerts will usually suffice. The manual says it will take only 8, although users here have reported success upgrade to 16. There are 2 slots on the motherboard.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Malware & memory access problem

  I have a problem I have the thing about security scam "Smart Antivirus Protection" that appears on and outside. I ran a scan that tells me I have a problem to access memory at address Ox1FC408, with a note saying that if I see this error, operational information may be lost. Also this Trojan:Win32 / Sinada.R and Trojan: Win64 / Sinada have been detected but not deleted. How can I fix the memory access and to get rid of these problems of Trojan. Thank you.

  Hello
  Try following the steps in this virus/malware removal guide: http://www.selectrealsecurity.com/malware-removal-guide
  It contains instructions which will remove most malware infections. If you have any questions, just ask me. I hope this helps you.
  Brian

• memory access voilation

  I m using windows xp sp3 edition media center, 1.5 GB of ram.

  When you use tally erp9 my score program gets hanged and
  the error shows that:
  software exception c0000005
  (memory access voilation)
  I already formatted my system and downloaded the last
  security internet Kaspersky 2012 but showing the same thing again.

  Do a little research on Google, which seems to be a popular issue with Tally (especially after a score update/upgrade), but I have not found a "solution", but I did not read all the threads at the end then you want to do some research on Google and see what came you on their part.

  This c000005 error is a problem of "permissions" somewhere.  Something wants permission and cannot get it, if you get this error c000005.  It is probably not a Kaspersky problem unless Tally wants to change something and it does not leave by Kaspersky.

  Tally has its own support Page, so you can ask your questions here:

  http://www.tallysolutions.com/website/HTML/index.php

• HP Pavilion dv7 laptop: memory

  can I use:

  16 GB memory DDR3 1600 (PC3 12800) latency Cas 9 speed (2 x 8G)
  Schedule 9-9-9-28 voltage 1.5V
  Multi-channel Kit Dual Channel Kit

  in this laptop?

  Here are the Crucial http://www.crucial.com/usa/en/compatible-upgrade-for/HP-Compaq/pavilion-dv7-6c63nr memory.

  http://www.crucial.com/USA/en/compatible-upgrade-for/HP-Compaq/Pavilion-dv7-6c63nr

  I was unable to find guaranteed compatible expansion modules appear to be available to Kingston or Corsair.

  Guaranteed compatible using modules in a major memory manufacturer upgrade is the way to go if you want no surprises when you plug new modules. Do not add the new memory module that is already there. Remove the original memory unless you can locate a module that is identical in every respect to be placed in the empty soDIMM slot. You don't have to try to match the specifications of the module of the computer laptop memory published unless you like surprises.

• Error when you try to play the game: memory access violation

  memory access violation

  I have redownloaded a game that has been previously loaded on my computer, now I get this error when you try to play the game "Memory Access Violation".

  Your sound card that is more than adequate.
  If the game was previously installed and worked fine then maybe it is not been completely uninstalled.
  I suggest you uninstall the game, look in the registry for any left over entries that can refer to the game.

  Then restart and reinstall the game.

  Alternatively, you can try to install in compatibility mode. If the program is not compatible, then you try to install and run the program in compatibility mode.
  Use the following steps:
  (1) right click on the program
  2) click Properties
  3) click on the Compatibility tab
  (4) select run this program in compatibility mode and select Windows Vista or other operating system, the program has been run successfully.

  Check out the link here: make sure to run older programs in this version of Windows
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  Let us know if that helps.

  Marilyn

• Do I need to install the player "Direct memory access controller? It is a 32-bit windows 7 Professional.

  Here is the story:

  I install an OEM Windows 7 Professional 64 bit for its new PC, he is not happy. and I replaced by 32-bit professional to formate the system with the same product key. (I ve been said the keys are for 32 and 64) and it works.

  A few days later, the customer complain that "Direct Memory access controller" is missing.

  He's going to the Device Manager, > system device, > "Direct Memory access controller", he said: "no drivers are installed for this device.

  But I check other computers are all the same, and people online says there is no driver for this at all.

  However, the client argued that this technician Microsoft told him the computer isn't good and 100% need the driver for it!

  It is "you can find or do we need this driver?

  Help, please!

  install the adapter driver mother and chipset driver or manufacturer of contact system