Pavilion P7-1240: Impossible to disable startup secure in the Bios

Similar Questions

• It will be possible to disable startup secure on a new Windows 8 laptop (HP Envy dv6t)?

  I'm planning a purchase of a new HP dv6t envy. It comes with Windows 8. I also intend to dual boot it with CentOS. I just need to know if there is a way to disable startup secure UEFI to allow me to start Linux.

  Yes, secure boot can be disabled in the bios.

  See screenshot below

  .

  

• ProDesk 600 G1 BIOS configuration of the TPM secure through the BIOS Configuration utility

  We have a range of devices, computers HP desktop and laptops in our environment.  Devices are all running Windows 7 64 bit and should have Bitlocker enabled, but we found that some were not encrypted.  So I am trying to set up a remote BIOS and Bitlocker config activate software that we can get out via SCCM and then embed in a task sequence image for new machines.

  I use the Bios HP Configuration utility to check a BIOS password is set and then activate the TPM chip.  I took a BIOS config output of each of our models and created a settings file that has all of the TPM associated parameters of all models.

  At the moment I run Setup BIOS utility manually for testing.  On all models I tried that works very well, except for the 600 ProDesk G1 SFF.

  When I run the utility on the ProDesk 600 G1 MFS, it says that I have managed to update the settings, and when I check the BIOS, the TPM secure has been unhidden and the TPM Management was given to the operating system (two settings I change), but the TPM itself remains hidden.

  It's the release of the BIOS configuration utility (it uses the 2.60.13.1 version, which uses plaintext passwords.  I also tried with the 3.0.13.1 later version that uses password files - same result)

  C:\ > BiosConfigUtility64.exe /cspwd: "password" set: "TPM_Config.REPSET"
  
  < BIOSCONFIG Version = "2.60.13.1" Computername = 'HP600G1' Date = "24/07/2014" Time = "13:01:37 ' UTC '1' = >"
  
  < SETTING changeStatus = "pass" name = "Embedded Security Device" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [hidden device]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [device]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "Enable security on the next boot" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "The BONES of on-board safety management" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SUCCESS msg = "Successfully set BIOS config." / >
  
  < information msg = 'BCU return the value' real '0' = translated = '0' / >
  
  < / BIOSCONFIG >
  
  C:\ >

  And after a reboot (where it should activate the TPM), BIOS shows as disabled built-in safety device (see attachment for the image).

  I have tried everything I can think of to get this to activate, including:

  • Different versions of the BIOS configuration utility
  
  
  • Remove the password from the BIOS and the application in the same order as the parameters
  
  
  • Different passwords
  
  
  • Reboot and allowing the machine to start completely to Windows before checking if the setting took effect

  I also tried to add the utility and the commands for an SCCM package and it works directly and as part of a sequence of tasks to see if that makes a difference, but nothing I've done has activated the TPM module.

  I know that the TPM module works, as you can turn it on manually and then Bitlocker can be applied to the machine, but with thousands of devices in our environment, I need to get this job without the need for manual intervention.

  Has anyone else had this problem and found a solution?  Or has someone at - he managed to activate the TPM on the SFF of 600 ProDesk G1 using the BIOS Setup utility?  Any ideas / suggestions would be very appreciated!

  P.S. This thread was moved from the company PC - Compaq, Elite, Pro for HP PC Client management. -Hp moderator of the Forum

  This problem has now been resolved by HP.
  
  They provided a replacement motherboard for the test machine I was using that solved this problem. I don't know what kind of motherboard failure could prevent the activation via the script TMP chip but not prevent activation through the BIOS menu, but as a replacement solved the problem, then it must be a hardware failure.

• Accidentally disabled video card in the BIOS, now just a black screen

  I am writing to my brother-in-law because he can't see anything out of his monitor.  Its screen is completely black, even at startup.  He said that this was due, after having entered the BIOS and under the framework to monitor/video card PCIe to Onboard.  It can't change because its screen is now completely black so he can't see what she does.  Not one thing is displayed, not even the screen blue intro HP before loading Windows.  The computer does not seem to work, but it's just, that there is no video input.  Does anyone have a recommendation?  Here are a few things we considered:

  (1) temporarily add a new video in the PCI slot card, hook the monitor up and allows to change the setting back.

  (2) remove the battery of the BIOS for 5-10 minutes, and then move back in.  Would this reset the BIOS to its original settings?

  (3) clean sweep with factory recovery CDs.  Does anyone know if the recovery CD will also retrieve the settings of the original BIOS?

  The computer is a HP Pavilion m9000t.  Any input would be greatly appreciated...

  Hello

  Remove the RTC battery for more than five minutes (BIOS) clears all custom (including time & date) the BIOS settings and return all the default settings.

  Kind regards

  ERICO

• Desktop Pavilion 500-210 a: do press F10 to enter the BIOS? I would like to try Linux Mint via USB

  Hi, thanks for reading.

  Am I right in thinking I have to get into the BIOS press F10? To get startup options?

  I would like to try Linux Mint on USB I already created.

  Thank you very much.

  Anthony

  Anthony, welcome to the forum.

  Yes, you start typing F10 as soon as the computer begins to start.  This will take you to the configuration of the BIOS page.  Then, search for the configuration of the boot order.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• How can I disable "SATA" option in the BIOS PHOENIX Satellite M70

  My laptop is toshiba satellite M70
  He has PHOENIX bios
  is there any FLASH ACPI for this Bios for me to set the property as DISABLED SATA?
  OR I can DISABLE this property is the current BIOS?
  Thank you very much...

  Satellite M70 does not support this feature in the BIOS!
  This means that you will not be able to disable the SATA feature!

  As Akuma, you need to install the SATA driver first.
  You can do this by using the USB external floppy drive or you will create the new CD of Win XP and will include the SATA driver using the free tool called nLite.

  So if you don t have an external USB FDD drive, you can use nLite.

  Search here in the forum for nLite and how to include the SATA drivers.
  There are a lot of announcement about this procedure.

  Good bye

• Pavilion Mini 110: Mini 110 suddenly invite you for the BIOS password after hard drive failure

  After mini disk failure hard full sat for a long time. So, I'm going to replace hard drive today and it is stuck on the screen of the BIOS password! After that 3 wrong attempts it gives an error CNU9283Y90

  I tried to unplug the CMOS battery, wait awhile, and then tie... no go!

  Can anyone help!

  TIFF

  TIFF.

  Enter e9lo7ufio1

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  If demand for CURRENT password using this code.

  Request NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

• After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter the BIOS setup

  After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter into the BIOS setup (via the ESC key).  I installed the BIOS twice and the computer always ignores the ESC key and launches Windows 7.  Any ideas?

  Well you're response made me experiment more and I discovered that the ESC key works if I type repeatedly instead pressed constantly.  Thank you for taking the time to answer!

• HP Pavilion years 1240 g6: beep on startup without Starter

  At first until it beeps and it does not open. And when it opens start as normal video will not play

  Dear customer,

  Welcome and thanks for posting your question on the Forum from HP Support.

  Please open this web link to isolate the problem, you said it's beep check then the link given below to resolve the problem:

  http://support.HP.com/us-en/product/HP-Pavilion-G6-1200-notebook-PC-series/5145704/model/5170264/document/c01732674/

  Hope this helps, for other queries in response to the post and feel free to join us again.

  * Click on the white button on the right to say thank you Thumbs Up *.
  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you
  VSL85
  Although I am an employee of HP, I speak for myself and not for HP

• Impossible to assign a security to the YEARS

  Hello
  I am trying to set security for "Grant access" to my dimension of years. When I edit Dimension, it shows that the option 'Apply security' is already checked and used in output so that I can not change it.
  
  However, there seems to be no way to assign a security to give users READ access to AFA 08 historical and WRITE access in FY10. This seems to be the expected behavior, but what do I do to assign a security?

  Hello

  Security is not applied to the years, you can set the opening year of start/end of scenario.
  Take a look at the sceanrio rating settings, you will see start and end year/periods

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Satellite M30: How disable the BIOS boot password?

  Hello

  Before my vacation, I activated the startup password in the Bios. Now I want to turn this off, but it does not work. In the Bios, I can go to the Security tab, but I can't change the settings with the F5/F6 key or space. A beep is all I get. Entering on this point, I wonder to set a new password.

  Anyone know how to disable the password for a Satellite M30? Please note that I have not forgotten my password, I can always start the machine.

  THX,

  Werner.

  PS On this forum, I don't see any topic title, only the name of the authors. Is always normal? It is very convenient that way, but maybe it is related to my pc.

  Hello

  I found a step by step explanation to clear a BIOS password:

  "Turning on the computer from a State"off"with the ESC key. You are asked "password =". "

  Enter the password, and then press ENTER. The unit will display: "the valid password is entered, the system starts up. Check the system. Press key (F1). »

  Press the F1 key. This will start the device in the BIOS Setup mode.

  Using the arrow keys or tab, move to the password field and select REGISTERED.

  Press the SPACE bar, enter the password, and then press ENTER. For now, the password field is transformed into NON REGISTERED. »

  Hope this will help you.
  Good bye

• HP Pavilion ze4936ea: update the BIOS.

  I have a HP Pavilion ze4936ea (PN624EA #ABU) is all about 2005.
  The BIOS revision was F.15 and I downloaded sp31140.exe to e.16.
  I don't have what I had when I upgraded to e.16.

  I tried to update the BIOS because it indicates by error that there is a floppy drive or a USB Flash drive at startup. But it is not a Floppy drive in the ze4936ea and I had a program on USB I tried to start from! The program BIOS F.15 erred. As well as the program e.16 BIOS, which also indicates a floppy drive, but no USB Flash drive in the laptop.

  What's not here?
  Can I get a BIOS program that allows me to boot from a USB Flash drive?

  The system BIOS has not the ability to boot through USB devices. I suggest that you create a bootable CD with the utility you have on the USB flash drive.  Here is a link that allows you to create a startup disk:

  http://www.computerhope.com/issues/ch000669.htm

  You will only have the four boot options following for your system:

• HP Pavilion 15-n236tx: reset the BIOS

  I have a laptop HP Pavilion 15 15-n236tx and I don't know the bios password because I don't know who put this password. So I tried to enter the code found on some web sites, and now the bios is locked. Disabled system code number is 75726848. Can you help me, please.

  Enter >

  60684288

• Pavilion dv6 Notebok PC: programs to disable startup?

  Hello! The startup got a bit slow and not wanting to mess up my computer, I'd like to get your expert opinion on what can be disabled startup! (ZoneAlarm's security system, I am currently running)

  Here is the list of what is currently at startup:

  Intel(r) Common User Interface

  Intel(r) Common User Interface

  Intel(r) Common User Interface

  Synaptics Pointing Device Driver

  IDT Audio of PC

  THE Bluetooth service control program

  Intel PROSet\Wireless Bluetooth

  Akamai NetSession customer

  Autodesk 360

  Microsoft Windows operating system

  Intel (r) USB 3.0 to monitor

  HP screen

  PowerDVD RC Service

  CyberLink brs

  Cisco AnyConnect secure mobility Client

  AcroTray - Adobe Acrobat Distiller assistance request.

  Citrix ICA Client

  Citrix ICA Client

  Java (TM) Platform SE Auto Updater

  hpwuSchd Application

  Quick menu for Canon

  ZoneAlarm

  Adobe Systems, Inc. Adobe Gamma Loader

  InstallShield

  Start Adobe Updater utility

  Apple Push

  Microsoft Office 2010

  Update Facebook

  Google update

  Google Chrome

  HP Quick Launch

  iCloud for Windows

  iCloud for Windows

  iTunes

  QuickTime

  HP Digital Imaging

  Phew... a bit long! I'd appreciate any help on what can be disabled safely!

  -Fred

  Hello

  You can disconnect the following progrsams, disconnect these programs means that it what would does not start when windows starts unless you want and click on the respective icon to launch.

  Akamai NetSession customer

  Autodesk 360

  PowerDVD RC Service

  CyberLink brs

  Cisco AnyConnect secure mobility Client

  AcroTray - Adobe Acrobat Distiller assistance request.

  Citrix ICA Client

  Citrix ICA Client

  Quick menu for Canon

  ZoneAlarm

  Adobe Systems, Inc. Adobe Gamma Loader

  Apple Push

  Microsoft Office 2010

  Update Facebook

  Google update

  Google Chrome

  iCloud for Windows

  iCloud for Windows

  iTunes

  QuickTime

• Disable a startup secure on my HP envy phoenix 180-145qe

  I have

  If I may ask, why do you do this?

  Did you mean to type HP Envy Phoenix 810 instead of 180?

  Enter the BIOS

  

  

  

  Once you have pressed F10 to confirm the change, click the file tab, then click on save changes and exit.  You have disabled the secure boot.