PC does not start when you press the power button, after that starts automatically as a ghost!

Similar Questions

• Tecra A4 does not light when you press the power button

  When I press the power on button it turns green for 4/5 seconds then turns off.
  "I do all the tests the support on the page:
  
  * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

  * Connect the adapter to the computer.

  * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

  * Plug the power adapter into a different plug.

  * The battery, ensure that there are enough energy to start the computer.

  * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

  * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

  * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

  * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
  In vain:]

  You know? THX

  Hello

  There must be a hardware malfunction.
  You have tested a lot and nothing has worked
  I think there is not much to do, you all tired and I guess the authorized service provider could help you

  If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

• Volume/brightness does not appear when you press the volume button on laptop keyboard

  Recently, when I went to change my volume, the small bar has not appeared on my screen, showing how much I was going to the top. Brightness bar did not show either and it's really annoying because I never know how it is until music strikes out. Any suggestions on how to fix it? I'm totally lost.

  Hello

  I apologize for the delay in responding. It seems that the user profile that you are using has gone corrupt. Try to create a new user profile and check if you have the same problems here as well.

  1. open user accounts by clicking on the button start the picture of the Start button, clicking Control Panel, clicking user accounts and family safety, then clicking on user accounts.

  2. click on manage another account. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. click on create a new account.

  4. type the name you want to assign to the user account, click an account type, and then click on create an account.

  Create a user account
  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  To fix the corrupted profile follow the steps mentioned in the article below.

  Difficulty of a corrupted user profile
  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  Try using the tool (SFC.exe) System File Checker to check and repair corrupt system files.  To do this, follow these steps:
  How to run scan SFC

  1. click on the Start button

  2. on the Start Menu, click all programs followed by accessories

  3. in the menu accessories, right-click on command line option

  4. in the drop-down menu that appears, click the "Run as Administrator" option

  5 If you have the enabled User Account Control (UAC) you will be asked to consent to the opening of the command line. You simply press the button continue if you are the administrator or insert password etc.

  6. in the command prompt window, type: sfc/scannow then press enter

  7. a message is displayed to indicate that "the analysis of the system will start.

  8. be patient because the analysis may take some time

  9. If all of the necessary files any replacement SFC will replace them. You may be asked to insert your Vista DVD for this process to continue

  10. If all goes although you should, after the analysis, see the following message "Windows resource protection not found any breach of integrity.

  11 after the scan finished, close the command prompt window reboot the computer and check.

  For more information, see the link below.

  http://support.Microsoft.com/kb/936212

  Let us know if this helps

  Concerning
  Anthony.

• My cd-writer/DVD disc tray does not open when I press the Open button. He is not blocked and has no disk in it. How can I me t to operate?

  Cd-writer/DVD disc tray does not open when you press the Open button, or when you use the buttons to control the media on the keyboard. How can I restore it to its operating state?

  Hi John,.

  Please let me know exactly what happened when you tried my suggestions of first and second.

  Of your most recent post, looks like you're watching the wrong part of the Device Manager. Optical drive is listed under "readers of CD-ROM/DVD-ROM". The info you gave appear under "drives". If the drive is not listed under "readers of CD-ROM/DVD-ROM" or there is no such section in Device Manager, then Windows do not see. If windows can't see it then this means that there is no power or that the drive is broken.

  When you pushed the drive back in, the player no longer has much of the book or did you have to push all the way. If the latter, it means that the drive has no power or is broken.

  With respect to the opening of the case, I guess I should ask first if it's a laptop or desktop?

  Tricky

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• PowerEdge T410 won't do anything when you press the power button / stop.

  My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

  -Who-

  I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

  Problem solved

• new tab does not appear when you press the button "open"

  A few days ago I suddenly can not open a new tab when you press the button open tab , press file-> open the tab, or Open the tab button next to a tab...

  Uninstall the toolbar Ask and it should work again. There is a compatibility issue with the Ask and Firefox toolbar that prevents the opening of new tabs.

  There are a few places to check for the Ask toolbar:

  • Check the control panel Windows for the Ask Toolbar - http://about.ask.com/apn/toolbar/docs/default/faq/en/ff/index.html#na4
  • Also check your list of extensions, you may be able to uninstall it from there - https://support.mozilla.com/kb/Uninstalling+add-ons

• Dashboard does not appear when you press the button on the dashboard

  I just got my board replaced on my MacBook Pro.  Before it was replaced, when I pressed the button with the dashboard icon (F4), it is toggled between my widgets that have been opened in the dashboard and the window, in that I was working.  Now, after you set up the Mission control to show the dashboard with the key to the dashboard, I see the dock (which I choose to hide) and all my apps icons.  I then have to click on the application of the dashboard to show my widgets.  How to reset the key so that it only shows the widgets when I press on it?

  Try going to system preferences > keyboard and check the box use F1, F2,... etc as Standard keys.

• Loop will not stop when you press the stop button

  Hello

  I have a LabVIEW program that includes a number of loops, but one of my curls (which surrounds a series of functions "Write TDMS") has a Boolean stop that transmits a signal through two GOLD and functions in a control of the loop (see aea of interest). My problem is that when I press the button stop the loop will not stop and will continue to save and write data that I didn't need a file.

  Could someone please help with this?

  Kind regards

  Aaron Broady

  
  

• Audio does not play when you press the arrow keys.

  Hello

  When I'm working on a project and I press the left or right side of the keyboard arrow keys to move a picture in the timeline, the audio does not play.

  He used to play and also appear in the audiometer as a level, but recently he has ceased to be. Maybe it was because of an update?

  Is it possible to turn it back on? Maybe I hit a button by accident and disabled the function.

  If it is due to an update, is there a way to revert to a previous version?

  Looking forward to you soon.

  Thank you for your time and help in advance.

  All the best

  George

  Mac OS X El Capitan 10.11.1

  iMac 27 inches, end of 2013

  Processor Intel Core i7 3.5GHz

  16GB 1600 MHz DDR3 memory

  NVIDIA GeForce GTX 780M 4096MB graphics

  First Pro CC 2015.1

  9.1.0 (version 174)

  Please let me know if you need more information and I will be happy to provide it.

  Try pressing SHIFT + S, which is the shortcut for "toggle Audio while Scrubbing."

• Audio, attached to the text box does not restart when you click the Replay button

  Hello

  I'm currently having problems with audio / reading slides. The characteristics of sliding replay I tried (listed below) read the images and text boxes, but the audio attached to text boxes do not restart, continue as if nothing has happened during the synchronization of text boxes and images have been reset. This happens also with videos and flash files - the slide reads but the videos and flash files continue to play.

  The two replay options slide, I tried:

  With the help of a widget: http://www.cpguru.com/replay-slide-widget-for-adobe-captivate/

  Advanced use of stocks: http://www.youtube.com/watch?v=vhT7B5I3fw8

  Is there a setting I can change to make audio/video restarts along with other objects on the slide?

  Thank you!

  I thought about it--(yay!)

  Here is a screenshot of the code that worked... need to replace a 'framework' with a 'landslide' command command

  

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• My his laptop makes a beep when I press the power button / stop and it does not start

  Hello

  I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

  -Mayur gala

  Hi Mayur,

  Welcome to the community,

  Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

  See the table below which shows the beep codes and the possible problem:

  Overview of beep Code
  Beeps	Description	Possible cause
  1	ROM BIOS checksum failure	The map system, covers BIOS corruption or errors ROM failure
  2	No memory (RAM) detected	Memory or memory slot failure
  3	Chipset error (North and South Bridge error) Time-Of-Day Clock test failure Gate A20 failure Super i/o chip failure Keyboard controller failure	System board failure
  4	Memory read / write failure	Memory failure
  5	Real Time Clock (RTC) power failure	CMOS battery failure
  6	Video BIOS	Video/smart card failure
  7	Failure of the CPU	Processor failure
  8	LCD SCREEN	Failure of the LCD

  Let me know if you need assistance.

  Thank you

• SpeedGrade CC14 does not open when you use the "Direct Link to Adobe SpeedGrade... "of PremierePro CC14.

  SpeedGrade CC14 does not open when you use the "Direct Link to Adobe SpeedGrade... "of PremierePro CC14.

  I can open the SG of start menu/desktop computer and I can open the PP project in SG very well. The PP project contains 3 deadlines and I take one I want without any problem. Returning to the SG PP works fine as well. It seems only thing doesn't work does not automatically open the PP file and selecting the correct timeline in the Official Journal of the project.

  I had a glance at the "C:\Users\john Bishop images\AppData\Roaming\Adobe\SpeedGrade\8.0\logs\SpeedGrade.log ' but it is not updated when I try to use the link Direct from PP. command It updated when I invoke the start menu/desktop computer SG. Note that none of the other newspaper, the files are updated either (Plugin Loading.log, Database.txt Trace and Debug Database.txt). All these get updated when I run the desktop/start. It would appear that SG is not yet known.

  I uninstalled the SG and the PP and re-installed (all in the directories by default) and everything seemed to go OK but no change.

  I also added 2 political profile the NVIDIA Control Panel, just display a message when loading SpeedGrade.exe and another for a slightly different message when loading SpeedGradeCmd.exe. SG invoking the desktop/start causes the SpeedGrade.exe message to display. Using the 'Direct link' PP file option does not display anything, reinforcing my thought that SG is just never called from PP.

  SP1 Windows 7 Professional 64 bit

  12 GB OF RAM

  2-Intel Xeon E5640 (16 sons) processors

  NVIDIA GeForce GTX580 1536 MB memory graphics

  PS... I used the Adobe cleaning tool noted elsewhere and tried NVIDIA workarounds as well - all to nothing does not.

  Problem solved!

  My Antivirus software was in the way. Once I have updated, things work fine.

  Thanks for your help!

• Microsoft Pinball Arcade, everything works except the right flipper does not work when you run the game. __Keyboard is very good

  Microsoft Pinball Arcade, everything works except the right flipper does not work when you run the game.
  Keyboard is fine.  Is this a compatibility issue?

  ---------------