PCI bus 0, device 2, function 1
Hello
I have a problem with my video controller device driver after installing windows 7 (from windows xp)
information about the location: PCI bus 0, device 2, function 1
Hardware ID: PCI\VEN_8086 & DEV_2792 & SUBSYS_3081103C & REV_03
Full name: other devices / unknown device
My laptop is: Hewlett Packard Pavillion dv 4000 (Ek919EA #ABH)
Properties: The drivers for this device are not installed. (Code 28)
The installation failed because a function driver was not specified for this device instance.
Please help me to find and download
Thank you
Hello:
Download and run this file. You will probably get an error not supported operating system.
FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34749.exe
Conclusion of any windows error.
Go to Device Manager and click on the device video controller requiring driver.
Click the driver tab. Click on set to update driver.
Select her browse my computer for driver software option and find the folder of the driver that was created when you ran the file.
This file will be located in C:\SWSetup\sp34749.
Make sure that the include subfolders is selected and the driver should install.
Then, restart and graphics need to be working very well.
Not that Windows Aero is not supported on this model graphics card.
Tags: HP Desktops
Similar Questions
-
Z820: Z820 Windows 10 question - pci bus 0, device 22, function 3
HI guys! Try to set up a fast enough for 4 k machine NLE here, began with a refurb Z820. Managed to get 10 Windows running without much of a fight. One last question, that I can't understand and I watched and read until my eyes covered in blood with no posotive result.
In - other devices - Pci Serial Port Device Manager. I have a Pci bus 0, device 22, only function 3 no error driver installed. As far as I know I installed all the drivers, updates, etc., etc... at least two times.
As everyone on this forum has more experience with HP workstations then I thought that I would return it to the wiser.
Thank you for your help.
o.k. now.
Retrace my steps, always a good thing when lost and confused, I realized that when I installed the Intel sp744499.exe management software, I didn't follow directive and that run the extract program of it is installed destination! Down & here when end of step B as written in the release notes, you no longer have to fix the latter on issues. Lesson learned - read all the instructions you can find, including the release notes.
Thanks again to Paul who tried to save my sight.
-
Unknown devices (PCI bus 9, device 9, function 2, function 3)
HP Pavilion dv6699ed
After a clean install of Windows 7 Ultimate 32 and drivers/software updated for the quick launch buttons and fingerprintdevice, I still 2 unknown devices:
Bus PCI 9, device 9, function 2
Bus PCI 9, device 9, function 3
For both devices, it shows that the drivers are not installed.
Can you help me by saying what are the devices and drivers, I need to install?
Thanks in advance.
Frans
Message edited by cowkof on 01/12/2009 09:29Message edited by cowkof on 01/12/2009 09:58Install the HP Vista card reader driver for your model to solve the problem with the Base system device:
Ricoh 5 - 1 card reader driver here
When there's some sort of problems with installing and then try to run in Vista compatibility mode.
Resources:
-
Help, please.
Hello
You need the driver for your Ricoh card reader - if you need a direct link to this can you post back with the complete model number and Nr of the laptop (from under your laptop service tag)-see here for an explanation.
Kind regards
DP - K
-
location PCI bus 5, device 0, function 0 code 28
Hello Mark135,
Thank you for your message. Go to the Web site of the manufacturer of your computer and download/install the latest network driver for your computer operating system. Please let us know if it did or did not help to solve your problem.See you soonEngineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.
-
Satellite A100-926: unknown device bus pci7; device: 6; function: 3
Hello world
I have an A100-926, device management, it shows me that there is an unknown pci device on the bus 7. function 3, but there is no way to know what is it and how can I install it because if I Reinstall driver it don't think the right on the toshiba tool cd.
I don't know if it is related to that but in an application, the button Delete must pushed me for longer than a second to work :-(
Is there anyone who can help me?Thank you
You reinstall the operating system on your laptop?
Generally, the laptop is delivered to the image of Toshiba and there should be some unknown devices in Device Manager
In the forum guys have put the link to the very useful document from Toshiba.
It describes how to identify the unknown devices.
http://support.toshiba-tro.de/KB0/TSB57014E000QR01.htmMaybe this will help you to know which unit it is.
Then, you can download the right driver from the Toshiba page -
HP COMPAQ 6200 PRO SFF PC: Bus PCI 0, device 31, function 3 DRIVER
I HAVE A PC HP COMPAQ 6200 PRO SMALL FORM FACTOR I KEEP GETTING MESSAGE ' CAN FIND DRIVER FOR CONTROLLER of BUS SM THE DRIVER IS: PCI bus 0, device 31, function 3 WHERE CAN GET THIS DRIVER? Thank you
Hello:
Download, unzip and run the file setup.exe from the link below... then reboot the PC.
-
Satellite A210-1AH - USB conflict pci bus controllers resource at startup
Hello
I have a Toshiba Satellite A210-1AH
model without PSAFGE-05X01GDUWhen I start the laptop after the toshiba logo. The laptop gives the following error:
Bus ERROR USB controller resources conflict pci on the motherboard
Bus: 14, device: 06, function: 00Bus ERROR USB controller resources conflict pci on the motherboard
Bus: 14, device: 06, function: 01Bus ERROR USB controller resources conflict pci on the motherboard
Bus: 14, device: 06, function: 02Bus ERROR USB controller resources conflict pci on the motherboard
Bus: 14, device: 06, function: 03Bus ERROR USB controller resources conflict pci on the motherboard
Bus: 14, device: 06, function: 04Press F1 to load the default values, F2 for Setup
I tried:
-load the default values
-disconnect the dvd player, hard disks, memory
-disable the hardware in the biosCan someone help me?
PS. I can't find this model on the driver here, to download a bios update.
This model is not longer supported?Ronald
Hello
You can enter the BIOS settings? If you can do this by using F2 to start together to check and default settings if the same thing will happen again. You can try to put the bootable disc in ODD and try to check if you have access to the HARD drive.
If the same thing will happen again and again I'm afraid the motherboard is a failure of m.
-
error system PCI bus/device/function 000 h, then again with the number 0200 h
last night when I went down tmy computer and is gone sleep on that I left it and it usuallty just goes to sleep. Today, I am home from work to try to remove the mode "Eve". It wouldn't even turn it off and turn it back on to notice that my computer somehow managed to delete the operating system. so I don't have xp on my computer. I can not even access bios to check if something I messed up. So I decided to try booting with the disk. and this is where im stuck. I'm quickly beginning to hit 'r' to reformat the computer and install an operating system. He goes through when he's trying to do. I'm prompted with the error message
System error ' PCI Bus/device/function 0000 h.
PCI Bus/device/function 0200 h system error. "After a few minutes of doing nothing it says under that
"Hard disk write error!Press a key to continue. "
now, I thought that the memory of my laptop may be losing the connection. I've checked everything and it's all warm in its place even the hard drive.
is there anyone who can help me?
Hi DrewHuble,
Given that you have made to the formatting when you are prompted, it looks to the operating system is removed.
If you have important data on the computer, I would say that you wake the computer to any tech store to back up data and then reinstall Windows XP on the computer.
Install, reinstall, or uninstall Windows
http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall
-
HP Envy 17-3077NR - bus PCI 10, device 0, function 0 (Code 28)
Greetings!
Hey, I have a HP Envy 17-3077NR, installed a cost of Windows 7, I'm sure that I installed all drivers 64-bit HP drivers page, yet "PCI Device" is always on view under "Other devices" with yellow exclamation point. I checked the properties and it says ' bus PCI 10, device 0, function 0 (Code 28). Nothing helps, I have re-installed Realtek Card Reader, Ethernet and Bluetooth. Please help as I am setting up this device for someone else and you want to do things.
Thanks in advance!
Hello
You are welcome
The hardware id is for the Realtek card reader driver, so I suggest to try to reinstall it from the link below.
http://ftp.HP.com/pub/SoftPaq/sp56501-57000/sp56908.exe
Once completed, restart the laptop.
When windows has reloaded, check device manager again.
Best regards
DP - K
-
End of driver Dell xps l502x dinosaur. device function 0 PCI bus 5 0
Had to rebuild my xps l502x because it has been 5 months out of warranty and crashes due to overheating had begun to bother me.
Clean the entire computer, threw it all back together and for some reason task bar icons is not photos, will not open volume mixer controls, and I have 3 "missing" device base system all say PCI bus 5 driver function 0 0.
Are they related? and how can I solve this problem?
Hi gcustoms,
Please share the installed operating system. It seems that the Chipset drivers are missing. Here are the steps that you can follow to install the drivers:
- Click the http://dell.to/18NmI2Dlink.
- Enter the serial number of your system, and select the operating system.
- Under the section of Chipset, you will find all the drivers you need to install following:
- Intel Huron River (HM67)
- Renesas USB 3.0 host controller driver
- JMicron JMB389 card reader
Restart the system and check if the problem persists. If so, then share the screenshot of the Device Manager with all the appliances expanded so that I can share the correct set of drivers with you. Here are the steps to access the Device Manager:
- Press the combination of keys Windows Logo key + R key to open the dialog box run.
- Type devmgmt.msc, and then click OK.
- The windows Device Manager appears.
- Click the sign next to network adapters and expand it.
I hope this helps. Just reply with the results.
-
Win.7 bit 64 pro HP 6730 b
Unknown device on Microsoft ACPI-compliant system code 28
Unknown device on pci-bus code 28
Hello:
You need the driver for this device...
This package contains the software that allows the HP Quick Launch Buttons, which are special function keys on HP laptops. This software works with the notebook models that are running a supported operating system.
-
Recently, I have restored my laptop and there is a driver is not installed. I don't find it in the list of driver download.
My laoptop is HP Pavilion Notebook PC g6-1c71ca and I am on Windows 7 home Prem
the problem is PCI bus driver
In addition, my hardware like ID below:
PCI\VEN_10EC & DEC_5209 & SUBSYS_1695103C & REV_01
PCI\VEN_10EC & DEC_5209 & SUBSYS_1695103C
PCI\VEN_10EC & DEC_5209 & CC_FF0000
PCI\VEN_10EC & DEC_5209 & CC_FF00
Dear customer,
Welcome and thanks for posting your question on the Forum of Support HP
It seems you are trying to download the drivers for the Realtek PCIE card reader
Please click the watch link below to download and install the driver on your laptop
Hope this helps, for other queries in response to the post and feel free to join us again
* Click on the star of CONGRATULATIONS on the left to say thank you *.
Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.
Thank you
K N R K
Although I am an employee of HP, I speak for myself and not for HP
-
I have a PC Hp laptop model Hp 15-d017tu.
I have a windows 7 64 bit after the new installation of windows and installation of all the drivers for the chipset, a PCI Bus driver has not been installed.
Please tell me how I can install driver PCI.
Concerning
Sami zaoui
Hello:
If there is a device listed in the Device Manager, PCI should it probably this driver...
If this isn't the driver you need, I'll need the hardware ID the device requiring the driver.
Go to Device Manager and click on the device requiring the driver.
Then click on the Details tab in the upper part of the device window.
Now, you see a drop-down list of property and it is set by default to the Description of the unit.
On this list and select the item named hardware ID
After the first string of characters you see in the window that begin with PCI\VEN.
-
Dear Support, I have problem with PCI Bus for J0X84EA. I can't find drivers for device in the download section. Can you help me?
Best regards
Cristian
Try to install HP Support Assistant that will automatically download and install updates/drivers:
HPSA link:
http://WWW8.HP.com/us/en/campaigns/hpsupportassistant/hpsupport.html
Otherwise, you can download from a nexternal source:
Maybe you are looking for
-
Designjet Z2100: Buy a used Z2100. This who should I look for?
I am considering buying a Z2100 used to, essentially, a few cents of a liquidator for recovery. The printer has remained for months with no cartridge but some print heads (I know are probably trash). I have an another Z2100 that I can borrow the ink
-
AirPort utility no longer displays the strength of connection
Run the latest version of Airport utility and El Capitan (10.11.3) is no longer the strength of connection for each devices connected to the network. Instead of; Strong, good, fair or poor strength of connection I get now unknown. Does anyone know wh
-
After upgrading my series ideapad Y to windows7 the keyboard is now something weird. I put it to dualboot with the vista installation std and this under vista but not in Win7 the keyboard is a nothing KB with a numeric keypad. In Vista, it works with
-
Yesterday I installed Security Suite CA. It installs and everything indicates that it works correctly, but when I try to open a pop-up appears microsoft Windows telling me a pproblem occurred and the program stops, and then another pop up appears sa
-
In Win 7, I right-click on a picture file that I received as an attachment (Yes, it was scanned before opening) and I not know who is the sender and what is the file. When I right click on the file and go to 'Properties', under 'Security' ITI says th