PCMCIA card as a serial port RS232 on Satellite Pro 4200

Similar Questions

• Satellite Pro 4200: need driver card PCMCIA Win98

  Hello!

  Driver with Ms issues I´m 4200 laptop computer series with win 98. I managed to find the display driver, but the driver for pcmcia card is missing. And I can't connect to internet because im using for internet access Wlan pcmcia card.
  I m writing this with my friends computer.

  Could someone help me please?

  Hello

  AFAIK the PCMCIA port uses the common Windows drivers and so there is no driver PCMICA.
  I recommend you to install SP all the updates for W98
  In addition, you must enable the PCMCIA in the BIOS
  This should help to solve this problem.

• PCI Serial Port driver for 6000 Pro - > Windows Pro 8.1

  Hello!

  Any chance to solve the missing driver?

  Thks

  Hello:

  I have a HP 8000 Elite (which is similar to the 6000 Pro) as my PC Backup.  I've just pulled up and I see that the hardware ID's for devices are aligned with those of the pilot I posted.

  So, you will need to manually install the driver I posted first you said did not work in Windows 7.

  Here is how to do this.

  Download and run the file (sp45367) again.  Conclusion of any windows error.

  Now, implying that you have installed W8.1 64-bit.

  Go to Device Manager and click on the device serial Port PCI needing drivers.

  Click the driver tab.

  Click on set to update driver.

  Select Browse my computer for driver and then software method at the bottom of this window, select Let me pick from a list of drivers for devices on my computer.

  Select disk, and then navigate to: C:\SWSetup\sp45367\SOLinf\mesrle, and then select the administration technology Active Intel (r) - device of GROUND in the list and the driver should install.

  The hardware ID for my 8000 Elite PCI Serial Port is PCI VEN_8086 & DEV_2E17, and who should be the same as yours.

  If you have installed 32-bit Pro W8.1 find the mesrl file instead.

• Port Replikator for Satellite Pro S500-116

  What Replikatoren of Port can be used with Satellite Pro S500-116?

  Hello

  Dynadock can be connected to the USB port. If it's not important what laptop you have.
  It is important that your laptop support USB (USB 2.0) ports and compatible operating systems.

• Need new ports USB for Satellite Pro L450D

  Hello

  I ve tried to keep new ports usb for my Toshiba Satellite Pro L450D I ve called Toshiba and they said I have to put it in for repair, but the thing is - it's not is no longer in warranty so that I can t make and send to Toshiba for repair.

  for me would cost loads I ve asked Toshiba provide me for my laptop usb ports, but they won t so I would like to know where I can get these parts as one of my ports usb don t work because of my daughter in the first place to break them and the entire interior of the usb ports is broken.

  Help, please
  Thank you

  Hello

  At first, I must say that Toshiba service doesn t sell these small parts such as USB ports. USB ports are soldered to the motherboard.
  Where to get the new USB ports? Good question.

  I don t know where you MFL, but perhaps you should I use Google in your country and check if you can find some independent repairer for laptop and ask for help.
  I fear it won't be so easy to find new ports of m.

  What you can try is to buy defective mainboard in the hope of USB ports are OK and are trying to replace them.

• Qosmio F50 - PCMCIA card with 2 USB ports

  Hello

  I want to buy a PCMCIA 2 ports usb to my laptop (toshiba qosmio f50) card and I would like to ask if these two are compatible with my entry expresscard card.

  http://www.DeLOCK.de/Produkte/Gruppen/PCMCIA/Delock_PCMCIA_Adapter_CardBus_zu_2x_USB_20_61604.h tml? setLanguage = EN

  http://www.equip-info.NET/equipenglish/index.php?page=search&&series=&Kat=&ID=803&search= pcmcia

  Thank you

  Hey,.

  I think that the two cards are compatible because they take over slot ExpressCard so I think both cards will work.

  Alternative if you need more USB ports, you can buy a normal USB hub. I think that these USB hubs are cheaper and also provide two or more USB ports you can more connected devices.

• Send the command to laser sensor via a serial port RS232

  Hello

  I have a sensor of moving Laser of OPTEX FA Co., LTD. with a Communication Manual.pdf file attached. I modified the sample base series write and Read.vi of LV to send the command to the probe in order to receive a response. However, LV always returns an error on my VISA Write.

  In short, the structure of command for the sensor must have a form like this

  STX-command command-space-1 2 - ETX

  (more can be see the manual on page 3 or 18 of the .pdf file)

  where

  -STX: code showing the head of transmit data (02 H)

  -Command 1, 2: could be refers to table 1, 2 and 3 of the manual.

  -ETX: code illustrating the completion of data transmission (03H)

  For example, if I want to ask the sensor to send the data from A sensor head, the command must be

  STX-ABLE () A - ETX

  (20H) space is shown as ().

  I tried to send a string HEX (02 - 4 d 454153555245-20-41-03) for this command to the entry VISA, but all I get is ERROR.

  I enclose with this thread my vi and a printscreen of the ERROR.

  A lot a lot of appreciation for any help from any of you.

  I have my LV code can run successfully. He can read the COMMAND and return measurement data. The last time does not playback VISA because I used a cable RS232 to opportunity, and someone operated two pins (2 and 3) for another application.

• SD Card Reader does not work on my Satellite Pro P100

  Help, please.

  My card reader reads nothing at all. I have a P100-429. Could you please tell me how I make it work and what drivers to install?

  Thank you

  Hello

  Have you changed anything on the laptop?
  The laptop comes with preinstalled Toshiba recovery image and all the drivers and utilities are already preinstalled and you don t new drivers.

  In my view, you must first check if the card is compatible with your laptop.
  Are you sure that the laptop card reader supports the card to 100%?

• You are looking for a new graphics card with 1 GB of memory for Satellite Pro A10

  I am looking for a new video card with 1 GB of memory, preference but is RIMM memory ram in my office, but has a different type of memory in the description of the video cards.

  Is it important at all, the video card would work always?
  Thanks 1million
  Stephen

  I put t know exactly what you want to do, but I assume that you need this card for an upgrade.
  New bad guy! Laptop graphics cards are often fixed on the motherboard and cannot be deleted!
  In addition, you must know that the mobile graphics cards are simply different and you can't compare these chips with adapters for desktop PCs.

  Best regards

• Portege M200: serial port does not work with port replicator

  Hello
  I have a Tablet m200 and the top mentioned dock/replication PA3314-1PRP port.
  As the M200 has no serial port (rs232), I want to use the one on the docking station, but it is not recognized as a device on my tablet.

  Thew network connections and usb ports all work fine and the lpt port is shown in Device Manager. I have restored the Tablet and it still does not recognize the serial port.
  How can I get this port recognized so that I can use it.

  Thank you very much
  Lee

  Hello Lee

  I just, I can confirm that when you use the Replicator port advanced III with Portege M200 several ports do not work. Problem is that Portege M200 does not support these interfaces.

  This is a technical limitation and the port of mouse PS/2 port keyboard PS/2, serial port, I.Link (Firewire) port and DVI port will not be supported when Portege M200 is anchored on the Advanced Port Replicator III. :(

• PCMCIA card will not install on Satellite L30 - 10y

  Hi all

  I hope someone can help with this problem. I recently bought a PCMCIA card with additional USB ports for my laptop Satellite L30 - 10y. It works on Vista basic, anyway I shoved the card into the slot and let windows install the drivers, problem is it will not load I get an error message saying that the MDT-0002 device does not charge.

  Is it a Vista problem or Toshiba thing?
  Thanks for any help on this one
  Regards Ciaran

  Hello

  I doubt that it could be a matter of Toshiba.
  I googled a bit for this device MDT-0002 error, and this error using some PCMCIA cards on different laptops from different manufacturers under Vista OS.
  Someone said that the Pcmcia.sys (PCMCIA driver) must be updated.

  I also recommend to contact manufacturer of PCMCIA card support for more details on a few issues with the Vista operating system.

  Welcome them

• Impossible communication with an electronic card via the USB port of the United Nations

  Hello

  I must communicate with a normal electronic card a mini-USB port / USB (serial, COM4). This card transmits on the airwaves on a frequency range that I must address.

  When I plug, the PC detects it and accept it (I installed the driver). Plug-in the HyperTerminal in Windows XP to send instructions in hexadecimal this carte pour what change the range of frequency on which it issues.

  Furthermore, neither MAX nor Agilent Connection Wizard not the detected and none are able to communicate with it, everytime the same message error "no device detected".

  I tried under LabView to send instructions with assistant IIOA, no results. I also tried the instructions 'Config VISA' and 'Entry VISA', trying to write in hexadecimal and normal mode, nothing works. Under labView I have yet no error message, nothing. Nothing.

  I don't understand. I know that it is still possible to drive it under LabWindows, but under LabView (8.5) nothing, not a clue.

  I have the latest version OR-488. 2

  Y ' have a procedure to follow pour such communication of?

  Thanks for any help that would be welcome.

  Kind regards

  Zoe.

  Hello

  The NOR-488 driver. 2 is the driver for the hardware from National Instruments GPIB; If you communicate to the port of of a USB through, this will not impact your code or on the resources used. The only element in common with your VISA application EST enhancement. It provides a unified API pour different types interface with instruments (series, Ethernet, GPIB, VXI, etc...).

  Under MAX, on cannot hole your communication card, only the serial port. The first chose to do is therefore to ensure that the serial port 4 is clearly visible under MAX. You can then the uti Test Pannel VISA pour send and/or receive orders to/from your card.

  If these elements do not allow you to properly configure your hardware, n 'hesitate to send a capture d' screen of the configuration under MAX. If you have a CVI code that allows you to interact with the map, it might be interesting to join, so you can see how interactions with the material are made.

  Kind regards

• The VI "VISA set up the Serial Port" will only work at 9600 baud

  I wrote a Serial Port RS232 RW.vi monitor of ' "which works for most. The problem is that it will not meet the alternative port configuration settings... For example: the default RS232 serial port configuration is:

  (COM1, 9600 baud, 8 data bits, 1 stop bit, no without parity)

  As a test, I use a Null Modem cable to connect to my LabView Com1 port to another PC running RealTerm Serial Port Monitor... Using my "RW.vi RS232' newly designed with the port settings of (COM1, 9600 baud, 8 data bits, 1 stop bit, no without parity), I can send and cannot receive data back throughout the day no problem...

  However, if I configure the port "RW.vi RS232" all other configurations, such as (COM1, 2400 baud, 7 data, 1 stop bit, odd parity bits)... He will not take the expected risks and continues to operate @ 9600 baud rate etc.

  Then, I changed the settings default "RS232 RW.vi" (2400,7,1, Odd)

  He still refuses to derogate (COM1, 9600,8,1, no...)

  I also went in the Device Manager of Win XP on the system of LabView and configured manually Com1 2400,7,1, Odd

  and yet,... work at the "RS232 RW.vi" @ 9600,8,1, none

  Everyone can test my VI in the car and see if they have the same problem of not being able to see the new changes in the Port configuration settings... other than (COM1, 9600,8,1, no...)...?

  FYI... Unfortunately my LabView runs on Version 6.0, you may need to up-conversion of the attached vi

  Instead of simply appreciate the comments, you need to implement.

  Having closed VISA inside the loop is definitely the problem.  And Crossrulz is 100% correct about the problem being that the serial port gets zero to default baud rate after the closure of the port.  Here's the proof.

  

  Note that while may have set the port settings manually in the Device Manager, these parameters are reviewed by the pilot VISA.  If you look in the measurement and Automation Explorer under devices and Interfaces > serial and Parallel, you'll see the default settings using the VISA driver.  If you change this setting, your program will work as desired.  But this is not the appropriate fix.  The correct solution is to get the VISA close out of the while loop.

  The port settings are established in this order.

  1. by Windows device drivers.

  2. by the VISA driver as set in MAX.  Since you are using VISA, these settings will be automatically replace #1.

  3. by the port settings, you set programmatically in your LabVIEW program.

• Need new laptop - Serial Port

  Hello HP forums

  I've been looking around for a new laptop for some time now and the closest I got to my needs is the HP ProBook 650 G1 but I have a hard time finding with the specifications. I need.

  So if anyone can help me or point me in the right direction, it would be well appreciated.

  Here's my need:

  Built in Serial Port RS232 (a must have)

  Core i7 processor

  16 GB of Ram

  HD SSD 256

  Pretty good grafics (should be able to handle 3D AutoCAD)

  Min 15 "screen

  Danish keyboard

  Windows 7 Pro

  Thanks in advance

  Michael

  Solution with help out of this for a

  HP Probook 650 model G1: F1P32EA #ABY

  with 8 gb extra RAM

  and the change in HD at SSD256

• INTERNAL SERIAL PORT (RS-232, DB-9)

  I need to find a new model laptop which still has an internal serial port (RS232, DB9) for all connections of equipment we need to do.  Can someone tell me if HP still has one and which one.  We bought several units ProBook 6570 b a few months back, but they seem to not be available now.

  Louis, as requested, I write back with what I discovered.  The HP ProBook 640 G1 and G1 650 ProBook equipped with a serial port internal.  I am convinced that it is useful.  I ordered actually only a unit of i7 640 G1.