peak hold dasylab lite

I'm going to build a system to display the hydraulic pressure to tip during an impact event. I use a pressure sensor high frequency Omega DFX101 - 5K, an Omega VAC - PS1 power supply, OM-USB-1608 acquisition, Windows XP, DasyLab Lite, SuperLogics forn small PC, HDMI display. The advanced event lasts about 3 ms and I want to hold and display of pressure Ridge on a digital meter as large as possible on the monitor. I also need to compile the file and run it on a client computer running the Runtime. Not much, right?

With DASYLab Lite you do not have the module of statistical values, but you should have a way to block / Peak Hold module. Configure for Cumulative Maximum. Display in the digital meter set to display the Maximum.  You can make as big as your monitor digital meter display.

With DASYLab Basic or Full, you have more options.

With DASYLab Lite, you have the Options-> key Actions that allows you to define an essential feature which can reset the average block module when you click the key combination.

You cannot compile DASYLab in an executable file. The license of DASYLab Runtime executes existing spreadsheets (files *.DSB). You must ensure that the DAQ configuration is the same. With a single device, which should be easy.

Tags: NI Products

Similar Questions

  • DASYLab Lite, CompactDAQ Ethernet, "the stream blocked by a later module" error

    I receive the message 'the stream blocked by a later module' and then the execution stops. I tried to remove the modules without change. He usually stops 8 minutes, 20 seconds (500) in the race. It happened on two different computers (same network, however). How can I get my program to run longer (forever?)?

    I am using a cDAQ NI 9188 (CompactDAQ Ethernet chassis), NI 9237 (strain gauge module), NI 9211 (thermocouple module), OR-DAQmx 9.5.1 and DASYLab Lite 12.00.01. My program of DASYLab affect strips from 100 Hz sampling frequency. The calculation of the average (reduce) block performs an average arithmetic with the size of the interval of 100 and a block size of output of 1.

    Thank you!

    Which module complains about being blocked? Look at the title bar of the message - it should show the name.

    You can observe the locking by turning on pre-trial block view-Animation-FIFO.

    I am suspicious that average organizes blocks more were awarded.

    One thing to try and really monitor your computer after doing this...

    Go to the Options menu in the spreadsheet view, then open the General preferences. Change these two settings - see the image - turning them off. The risk is that your application uses too much memory, so, please, provide oversight.

  • Pouvez fpga peak hold

    Can FPGA peak hold as the drawing attached.

    The pulse of the Moose is all 0.3us wide. The scale of the hold of the tip is 20us.

    The peak amplitude is 0.8V.

    Thank you.

    The faster module input analog cRIO is the 9201, that samples at 500 kHz, which equals 2 us intervals.  It wouldn't be fast enough to take your pulse.

    Fastest card of the R series is 750 kHz, which is still not fast enough.

    If you've built a simple comparator circuit that would turn your pulse to a TTL level signal, you can connect to a digital input on the FPGA (probably R series only) and read pretty quickly.  You can use this signal to activate an exit market and stop right analog time.  It wouldn't exactly be a hold of the tip, but it would be close enough.

    I hope to get an answer to your question.

    Bruce

  • Turn to hightlight in Googlebar lite search

    Could you tell me how to disable point peaking at Googlebar lite please.

    Solved it's ok.

  • Ridges

    Hello

    I would like to compare the values of one signal (table 1 d) with each other and then displays the maximum value. But only if desired.
    It should be in principle, a peak hold function, I always displays the maximum value.
    In the "power FFT Spectrum.vi", there is such a "ridges". However, I don't know how I can integrate it without the "FFT Power Spectrum.vi' in my vi.
    Maybe someone can help me here.

    A picture of the vi says maybe more (the picture shows a first attempt, which unfortunately does not work as expected).

    Thank you and best regards

    Alesis

    All you need is a little help from Max & Min function (at least for the way I remember Max Hold)

  • Power SVFA - with an average of question spectrum

    Hi all

    I used the power spectrum of SVFA to treat a signal from a trasnducer of pressure. All the options associated with this block seems to work very well with the exception of the settings on average. I used Linear/One Shot mode and assign number ofa averages 20. The prioblem is once it reaches 20, it continues to go further. I added a boolean flag to check if she treated the number required of averages, he did in fact. So now I'm stumped. Restart of the averagting seems to work as expected so.

    Any thoughts?

    Oleks:

    The sounds and vibrations help file for the Modes of time on average, we see that this is expected behavior:

    "In an average of peak-hold, the largest value of sound pressure level measured in all the previous values is calculated and returned until a new value is greater than the current maximum. The new value becomes the new maximum value and the returned value until a new value is greater than it. Peak hold is not really a form of averaging because successive measurements are not mathematically average. However, as with other processes of establishing an average, average peak-hold combines the results of several measurements in a final measure. As for the average exponential, the process of averaging continues indefinitely. »

    So because Peak Hold do not average in the strict sense, it does not restart on average the number of averages you specified as RMS and the vector average which are a true average.

    Tori, w.

  • Min/max to accumulate dasylab peaks? Is this possible?

    In collaboration with Dasylab 10.  I'm looking to collect peaks min/max on a form of sinwave we will run.  Is this possible?  If so, how?  Or I have to just to oversample and sift through data?

    Thank you!

    Select this option.

    Use the statistics module called Minimum / Maximum.

    This will display the value (you choose minimum, maximum or both), or will display a TTL signal, with a peak TTL (5V) to record highs.

    Adjust the hysteresis value to avoid detection from noise and spikes, or use a moving average to smooth out the signal.

  • HP Pavilion 17-f065us: power and buttons f6 (Mute) remain lit after a stop on HP Pavilion 17 - f065us

    I have upgraded to Windows 10 in October 2015 and everything worked very well until about two weeks ago, I noticed that when I would stop my computer Power and buttons f6 would remain lit.  I would go ahead and close the lid of my but next time I would go to to open they would always be lit.  I have to press on and hold the Power button until the lights go out.

    Hello

    Try disabling the startup of Windows 10 hybrid - you can do the following.

    Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

    In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close open windows and stop the laptop by right clicking on the icon from the Start Menu, select prompt (Admin) and click 'Yes' to the uac prompt.

    Type (or copy and paste) the following command (including spaces) and click Enter.

    Shutdown /s /t 0

    Start Notepad and let Windows take over completely for a few minutes before checking if the lights now now disable to stop correctly.

    If this has fixed the problem, it may be useful by turning the quick start back on - sometimes simply remove and re-create the file will solve the problem.

    Kind regards

    DP - K

  • What should I do to make my music release, I tried to restart my phone but it is frozen on the peak of Apple's music. There is no sign in or buttons to click and I can not get to any of my music

    Ive tried everything to unfreeze it, but it won't unfreeze. It is stuck on the peak of Apple's music and I can't go to my music at all. I tried signing in and out and even turn off my phone, but it does not work.

    Try double pressing the 'home' button and drag the application to the top music. Then hold down the sleep/wake and the "home" button until the Apple logo appears. -AJ

  • DASYLab how to write data to a file every 15 minutes

    Hi all

    I use dasylab and datashuttle/3000 to record data. What I want to do is to write data to a file every 15 minutes. I use the milti-file, which can write data to the file diffenret, but how do I control the timing, as the journal data every 15 minutes automatically.

    The other problem is that I use FFT analysis of the frequency spectrum. How can I determine the value of frequency where the peaks that happens.

    Thank you

    Write less data in the file that you have collected requires the reduction of certain data.

    There are three techniques to consider.

    With an average or an average of block - both reduce the data by using a function of averaging, defined in the module. To accomplish the reduction of data, choose block or RHM mode in the dialog box properties, and then enter the number of samples/data values that you want to reach on average.

    Average - when you reduce the data, you also should reblock data using the block length of the change in the output parameter. For example if you enjoy at 100 samples/second with a block size of 64, the average module configured on average, more than 10 samples will take 10 times longer to fill a block. The initial block represent 0.64 seconds, the output block represent 6.4 seconds at a sampling rate of 10 samples/second. If you change the size of output in one block, the program remains sensitive.

    Average block - average values in a block against each subsequent block, where the average is based position. The first samples are averaged, all second samples are average... etc. The output is a block of data, where each position has been averaged over the previous blocks. This is how you will be an average data FFT or histogram, for example, because the x-axis has been transformed in Hz or bins.

    Second technique - separate module. This allows to reduce the data and the effective sampling rate jumping blocks or samples. For example, to reduce the data in 1000 samples / second to 100 samples per second, configure the module to keep a sample, jumping 9, keep one, jumping 9, etc. If you configure to skip blocks, you will not reduce the sampling frequency, but will reduce the overall amount of data in a single block 9, for example. It is appropriate for the FFT data or histogram, for example, to have the context of the correct data.

    Finally, you can use a relay and a synchronization module module to control. For example, to reduce a sample data every 15 seconds, configure a generator module of TTL pulses for a cycle of 15 seconds of time. Connect it to a Combi trigger module and configure it to trigger on rising and stop the outbreak directly, with a trigger value after 1. The trigger output connects to the X of the relay command input.

    In addition to these techniques, you can change the third technique to allow a variable duration using a combination of other modules.

    Many of these techniques are covered in the help-tutorial-Quickstart, as the data reduction is one of the most frequently asked questions.

    In regards to the FFT... use the module of statistical values in order to obtain the Maximum and the Max Position. The Position of Max will be the value of the frequency associated with the Maximum value. The output of the statistics module is a single sample per block. Look at the different FFT sample installed in the worksheet calculation/examples folder.

  • DASYLab V13 update included?

    Hallo!

    I have a small question. I was not able to understand it on my own on the site Web of Dasylab.

    We use dasylab V 11. There were 13 Version released a few days ago. These updates appear, or should I buy updates?

    Thanks for all the answers and have a nice day.

    Hilby

    The major version releases (from V11 to V13) are extra. In the United States, they are to the price of the license... DASYLab UPD Lite, DASYLab UPD base, etc.

    If you are in another country, you must contact your dealer. The price of updates may be different.

    If you have recently purchased 12 DASYLab, you could benefit for the update free of charge or at reduced cost. You must contact your dealer, since this forum is not on prices.

  • The speaker lite does not work

    Everything works but the light does not indicate its is.

    The speaker lite does not function although the button is on switch its market? Dv6 - 6033cl

    Hello

    Try the following.

    Download IDT Audio Installer on the link below and save it in your downloads folder.

    http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55094.exe

    One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

    When you are finished, stop the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery, connect the power adapter and start Notepad.

    Let Windows load fully, then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once done, restart the laptop.

    Kind regards

    DP - K

  • How to hold the pick is or the Valley?

    Dear all,

    I have a wave sampled, then I want to detect the peak of points (or points of the Valley) and hold the point until the next Summit points (or points of Valley) will appear.

    Now I can use the example of 'Pic Detector.vi' to get the points that I want to.

    But I don't know how to put the data in the chart. The attached picture shows the idea that I want.

    If you need more information to solve my problem, please tell me, thank you very much!

    Hello

    Here's a way

    detection of all indexes of photos to build the parts of the table with each min/max value then assemble

    tell if it works

    Concerning

    Tinnitus

  • OptiPlex 980, any diagnosis 4 lit and not start

    Hi all

    recently my Optiplex 980 refuses to start: when I press the power switch, starts a sequence of codes that always ends with the diagnosis of four all lit. The power switch is blue, and for a second flashing led hard drive. But nothing appens...

    Any idea?

    Thank you

    Tiziano

    Which doesn't seem to be a documented diagnostic led code...

    Have you tried to disconnect all devices except keyboard, monitor and mouse?

    Have you installed a new hardware or software recently?

    You can try to clear the BIOS:

    1. Power off, unplug
    2. Power button press / hold for about 15 seconds
    3. Open the case and remove the motherboard battery
    4. Power button press / hold for about 30 seconds
    5. Use canned air to remove dust bunnies
    6. Reinstall the PCI cards and RAM in their slots
    7. Replace the battery (use 3 volt CR2032, if this one is old, ~ $2)
    8. Case and see if it boots now with only mouse, screen and keyboard
  • BlackBerry smartphones all 4 LEDs lit on VM-605 visor Bluetooth speaker

    Unit has worked fine for almost a year. Am in the car this morning and all 4 lights were lit. I put it on the charger. Battery turned LED orange for a bit, then back to red. Never turned green.

    What are all 4 LEDs constant average power? Is there a way I can reset this device? Should I just wait until the internal battery runs down completely?

    Thanks for any help,

    Marshall

    Apparently, it is news to everyone.

    I can tell you all that no combination of keys pressing/holding on the Visor speaker will change or disable the LED display. I can also say that almost anything can have do, no amount of charge will fix it.

    That said, the only thing left to do is let it burn until the battery was empty and all the lights had been arrested. It's exactly what I did.

    Then, I put it on the charger. He immediately begins a workload with the battery LED RED only. In 3.5hrs, charge finished with battery GREEN LED lit.

    I turned on the unit and the British female voice said it to my phone. As nothing unusual happened. Make a call and everything worked normally.

    Then, if all 4 LEDs on sun visor Bluetooth Speakerphone VM - 605 are light, let it go ahead and burn the dead battery. Then recharge and everything will be normal.

    If the 4 LEDs lit is way of Blackberry to tell the user the battery is low, they should thought to allow loading instead of having to wait until the battery dies completely and THEN the device recharges immediate.

Maybe you are looking for

  • Power of the exchange rate in numbers

    Hello I create a Position size in numbers calculator for managing risk in the trading game. More commercial instruments denominated in foreign currencies and to work on what I am risking in Australian dollars, I need exchange rate feed numbers to cal

  • NIC not recognized on Satellite M30-642

    Hello After the installation of the new my OS from Microsoft, I can't connect to the internet once again, because my laptop does not recognize the network adapter.There is an error message: number 769: "the target is unknown."This is why I need your

  • Update portable drive to SSD, problems with the installation of operating system and recovery system

    Compaq Presario CQ71, (model CQ71-317EA) portable system, Windows 7 family 64 - bit edition Hi, I tried to upgrade the original 320 GB HDD to a 256 GB SSD. After that replacement of the naked NTFS hard drive to SSD format, I tried to do a "factory re

  • XP Pro product copy legal code coming up as not being valid.

    I tried to re - install my purchased copy of XP pro, as I have done many times. The reason was that the operating system did not work properly, this unknown reason. After that installation I tried to activate it, but it came with the product, registr

  • "Review updates" Vista sp2 page does not load.

    My computer has windows Vista Home Premium sp2 32 x and updates are checked for every day. There are 2 updates important and 2 Optional updates listed at this time. When I try to "review updates" category either important or optional page does not lo