Phone to the Call Manager express license
Dear,
Is the license of phone required for Call manager express or the license on the bridge of voice enough to operate the phones?
Kind regards
A device license is required for phones on CME. Reference numbers
FL-CME-SRST-5 =.
FL-CME-SRST-25 =.
FL-CME-SRST-100 =.
Aerts.
Tags: Cisco Support
Similar Questions
-
HWIC-AP more Call Manager Express?
It took me some time and many transfers of tftp to finally find an IOS which works very well with the HWIC-AP (wireless access point module) for a router in 2801.
What I was asking: is there an IOS which supports both HWIC-AP and also includes the Call Manager Express (CME)?
What feautures would you find using the IOS search engine?)
Thanks for all the ideas.
Marc
Use the IOS 12.4 (2) T1 or later to support the CME and HWIC-AP
-
Call Manager Express ATA187 Firmware update
Hello
I recorded with Call Manager Express 9.0 to ATA187 but I have a problem for outgoing calls using DTMF, I tried to put dtmf-relay into the pool of register of voice but without success, so I decided to update the firmware.
the problem when you go to download page you will find a .zip to the file not as before managing the .zup file and the upgrade of the firmware for the express appeal not found in any document because there is no way to upgrade through phones analgo
No idea how upgade using any way?
Hi mrmhar1408,
You must upgrade the ATA 187 for the latest firmware SIP (9.2.3) using this load file, ATA187.9 - 2-3 - 1.loads. It is in the zip file available on the download section of cisco.com to the ATA-187, the name of the zip file is cmterm - ata187.9 - 2-3 - 1.zip.
The process of upgrading of the ATA and SIP phones 187 s in SIP via CME are listed here. The process is essentially the same for phones and ATAs.
Note that you must also have the load the copied file first in memory flash TFTP server, that would be your router CME flash.
HTH.
Kind regards
Stefano.
-
The NAC Manager/Server license question
I use a pair of NAC Manager failover with 5 games of CAS servers. Each set of CAS servers is authorized to perform the different amounts of users. (i.e. 1500 or 3500) I loaded all the licences in the Manager. (All Coses PAK have been validly submitted by using the MAC address of the Senior Manager.) Is it possible to assign... or... How will I know which set of servers will be assigned the appropriate license for a specific set of users max?
It was only from pak or was it separate paks... because he's going like that with a pak u generate license for cam (this is the license for the number of servers it can handle)... for that you must provide the mac cam address. then for each server FO u can use even PAK or a new and mentions the mac address of the server here and makes the exact differenc... If you had separate Pak. each PAK is given based on the license you requested from...
-
THE UNIT TRANSMITS NO CALLER ID INFORMATION. DURING THE CALL MANAGEMENT
WHEN THE UNIT IS SET TO ASK CALLER TO CALL TRANSFER SETTING FOR A SUBSCRIBER... IT DOES NOT TRANSMIT THE CALLER ID #, SIMPLY SAYS THE CALL IS FROM A VM #. IS THERE A WAY TO UNITY BEFORE THE CALLER SOURCE ID #?
Thank you
STEVE
No, it does not support this.
-
Entry of the appellant for the call manager does not to the first entry, books on the second
Unity 4.0 (4) SR1, 7.0 (4) flat TSP
Have a call handler when option 4 as input, the appellant and the user calls into customer and they get the welcome message, but when they hit 4 it does not first time. Replays of greeting and they hit 4 again and it works fine. 4 is set to go Manager directory. 4 is a key blocked under the entry for the appellant. This happens whenever they call and get the salvation of the unit.
They have 2 extensions 4xxx configured on the system also.
The unit probably behaves correctly. To confirm that the unit made, turn on the microphone traces PhraseServertoMonitor and watch the appeal on PortStatusMonitor.
-
Want to know primary and secondary configuration to the call, Manager with the voice gateways
Hi all
Hope you all are doing well, I wanted to know that we have two other PRI service provider and we want one of them are primary and secondary schools on the other. We have two supplier dedicated 4-4 finish lines. Please provide me with the part of configuration that are required in this case and how to re a SP for primary education and another SP for secondary lines.
Thank you
Arjun keita
Hello Arjun,
For the full bridge configuration you can check the guides below, but for the PRI redundancy, you create dial-peers and specify the feedback:
https://www.Google.co.in/URL?SA=t&source=Web&RCT=j&URL=http: / / www.cisco...
Voice POTS dial-peer 1
Destination-pettern 0 t
Port 0/0/0:15
Preference 0
Dial-peer voice 2 pots
Port 0/0/1:15
Preference 1
Dest-model 0 t
Dial-peer voice 3 pots
Description incoming only
Incoming called-number. T
Direct inward dial
Aseem
(Please rate if useful)
-
Call Manager Express has no type 6961
Greetings
I have a 1861 with cme 7.1 router (I think, I got this from the show - telephone services) and when I try to add a new phone 6961, I did not have this type of guy.
Is it something about the compatibility of the cme ip phone or am I missing some configuration?
Thank you
Augusto,
Support for the 6961 started CME version 8.0 for SCCP and 9.0 for SIP
See the CME software compatibility matrix
http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm
Kind regards
Alex.
Please evaluate the useful messages. -
WWhat can other thrm use iCloud different accounts?
All I can suggest is to use different from the Apple ID and then enable sharing of the family.
-
Hello
What is the procedure to upgrade the call manager since version 7.1 of CUCM (MCS Server) to version 10.2 of CUCM (on the server of the UCS), please let me know the steps to what would be the backup procedures and upgrades.
Concerning
Gerard
I suggest reading this guide to make sure that you have prepared your environment to support the first 10.x. The link below also contains the path to upgrade to 10.0 (1).
One of the ways to do this is:
1 / apply cooling cop upgrade file on all servers in the cluster.
2 / upgrade the cluster to 8.6 (2). Make a backup of the cluster.
3 / build a cluster of servers 8.6 (2) on the virtual machines and assign them the same host name and the IP address of the cluster hardware. (You may need to keep these on a separate network until turn off hardware machines)
4 / restoration of the backup of the pile of material on the VM cluster.
5 / upgrade cluster VM to 10.0 (1).
http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/CUCM/upgrade/10_0_1/C...
-
Hi, I want to know whether or not our current phone system uses the CCM? Unfortunately, I know that even with our systems and next thing I know, it's that use us Cisco Configuration Professional utility to configure the phone display names and update the date & time.
Could someone provide me with the steps to check if we use CCM/CUCM? Sorry to be a beginner.
Call Manager Express, another acronym which is CUCME - Cisco Unified Communications Manager Express.
CME/CUCME is function of the router, you can access it via telnet/ssh.
CUCM can be access through GUI and SSH.
Kind regards
Mohammed Noor
-
Call Manager 6.1 network problems
I have a problem with my network drops continually calls phones or freezing. Its States CM low features disabled. We lose calls, phones are freezing intermittently.
Here is the hardware configuration: MCS-7828-H3
Platform Type 7828 3 H
Series MX282400CM
OS active 6.1.5.10000 - 10
RTMT shows opt-out phones, but I don't see all devices lose connectivity with the exception of some packet losses minimal for call manager. No other error not reported in to any device Cisco syslog for example, ping sent to all major network devices have 0 packets lost over the weekend, but 250 on 20 000 ping on the call Manager server is lost. I replaced the cables, cords and moved from the ports of the switch with no resolution.
CPU has never been higher than 24%
Virtual memory never higher than 30%
Active and Inactive partitions are 15% of disk space.
We have a 2nd NETWORK adapter on the server, but I can't configure this 2nd NIC as a stand-alone connection for the call Manager server, than as a failover for 1 NIC. Does anyone know how to configure this 2nd NIC to host all these servers IP services? Is there a way to replace the NETWORK card on those servers (not on site and have yet to open this box upwards) or do I have to replace the entire server?
Does anyone have any other suggestions on where to take my troubleshooting?
Thanks for all the tips!
Steve
Please see below, your right in thinking this could be a faulty network card, cable, I suggest you also to search in your STP configuration.
Error Message RTD-1-ADDR_FLAP [tanks] [dec] base10 relearning / min
Explanation normally, MAC addresses are learned once on a port. Sometimes, when a switched network RECONFIGURES, due either manual or STP reconfiguration, addresses learned on a port are relearned on a different port. However, if there is a port anywhere in the switched domain that is loop over itself, addresses will jump backwards between the real port and the port that is in the path to the rear port loop. In this message, [tanks] is the interface, and [dec] is the number of addresses being learned.
Recommended action determine the actual path (port) to the MAC address. Use the ethernet controller of debugging command EXEC addr the privilege of seeing the other path-port on which the address is redisplays. Go to the switch that is connected to this port. Note that the show cdp neighbors command is useful to determine the following switch. Repeat this procedure until the port is found who receives what it transmits and remove this network port.
Link to Error Message-RTD-1-LINK_FLAP [tanks] down/up [dec] times / min
Explanation this message means that too many events from the bottom up link was noticed on this interface: [tanks] is the interface, and [dec] is the number of times that the link goes up and down. This could be the result of reconfiguring the port, or it might mean a faulty device at the other end of the connection.
Recommended action if a person is to reconfigure the interface or device across the interface, ignore this message. However, if no one manipulates the interface or device at the other end of the interface, it is likely that the Ethernet transceiver at one end of the link is faulty and must be replaced.
-
Can I migrate a virtual computer to a new family of CPU? -Cisco Call Manager PUB/SUB
I currently have 2 host VMware ESXi 4.1:
1. Dell PER905 - running 16 x 2.39 GHz (core) CPU / Quad-Core AMD Opteron (tm) Processor 8378 (processor type)
2 cisco UCS C260 M2 (BASE-2646) - running 20 x 2,393 GHz (core) CPU / Intel (R) Xeon (R) CPU E72870 (processor type)
The main objective is to move 2 VM of the Dell host to the host of Cisco, the reason is because Cisco Support said that the virtual machine requires an Intel and not AMD they are currently. I currently have a Publisher Cisco Call Manager and Call Manager subscriber residing on the host of Dell, they are constructed (non - OVF) on this machine some time ago. We started to have problems with them and ultimately Cisco indicated above.
A few questions come to mind, can someone please shed some light on them for me?
1. can I migrate these 2 AMD to Intel VM, without her damage/destruction of the virtual machine? What that is the answer may be, can you explain to me the why? The answer to the migration of the CPU is dependent on the guest OS or what? I ask because I did this successfully on a Windows Guest OS virtual machine, but I guess it is that Cisco makes me hesitate/question.
2 would it not be better to each virtual machine rebuilt on the new host, rather than through migration for the purposes of the CPU?
3. What is the recommended method to endorse these VM, before proceeding with the migration? I'm not talking about save data in the call manager for reasons that I will perform a backup it first. I ask more along the lines of - for the love of the virtual machine itself.
1. can I migrate these 2 AMD to Intel VM, without her damage/destruction of the virtual machine? What that is the answer may be, can you explain to me the why? The answer to the migration of the CPU is dependent on the guest OS or what? I ask because I did this successfully on a Windows Guest OS virtual machine, but I guess it is that Cisco makes me hesitate/question.
You should be able to perform a cold migration. The concern is the guest operating system level. The Cisco device is probably a Linux distro. The distribution must use the AMD64 instruction set (Intel 64 compatible) and theoretically should migrate fine. However, if the guest what OS was improved the AMD CPU instructions, he can expect these features when you restart. We have at least a virtual computer in our environment that we need to stick to a certain family of Intel processor because the software license dig and binds to it, but this is the only scenario that I have met.
2 would it not be better to each virtual machine rebuilt on the new host, rather than through migration for the purposes of the CPU?
I feel better on the redeployment, but if the migration is successful and applications run stable, then you reaped just the benefits of virtualization.
3. What is the recommended method to endorse these VM, before proceeding with the migration? I'm not talking about save data in the call manager for reasons that I will perform a backup it first. I ask more along the lines of - for the love of the virtual machine itself.
You could do something as simple as the cloning of a copy. Depending on how you are approved for vSphere, you can have the POS to back up your virtual machine. You can also use a tool such as VMWare Converter or Veeam Backup and replication. Given the importance of these virtual machines, I would get at least 2 backups of different type. You should be able to validate any backup with VMWare Workstation prior to migration.
-
Can't see the caller on my iPhone to make a video call
How can I configure my iPhone 4s to display the appellant to make a video call. I can see me on my phone and the caller can also see me on their PC
I found my problem: I had two of names/contact Skype different requests for the same person. Once I deleted a 'bad', everything worked and I could then see the video on my iPhone.
-
Unable to answer the call of the CSQ
Hello
We have intermittent problems with some agents are unable to respond to a call for a CSQ. This seems to only happen when the call is transferred to one QSC to another.
Scenario of
The call comes on CSQ1 and Agent1 answers the call.
Agent1 forwards the call to CSQ2.
In CSQ2, Agent2 can see their status is set to 'Reserved' at the office of the Agent, but the appeal does not ring on their phone. The call is still active on the phone to Agent1.
Agent1 can try to transfer again, but the same problem occurs. The call seems to be stuck on the phone to Agent1.The question is not subject to an Agent or a CSQ, happened on multiple Agents in multiples of the CSQ. The agent is not a resource in both in these situations of CSQ.
We are running:
UNIVERSITY COMPLUTENSE OF MADRID: 9.1.1.20000 - 5
UCCX: 9.0.2.10000 - 71
Devices: IP Phone 7945, SCCP ProtocolAny thoughts or ideas are greatly appreciated.
Thank you.
You should try the region of the contact for this issue Center
Maybe you are looking for
-
My time capsule began to display the error "Internal drive repair needs" yesterday. It is still under warranty, but I don't have the files that were on this subject, and I can't get them off or connect. Is it possible to connect or get the files off
-
I have lsot the line in the spaces of the toolbar include 'file, edie, veiw, bookmarks, history, help' etc. ICAN get it by pressing Alt + F8, but it will when I press another button. How can I restore it permanently
-
Satellite L30 - DVD player will not read CD - R / CD - RW
I have a L30 with a carpet * a ram drive uj-850 s DVD. He reads prerecorded CDs/DVDs, but during the insertion of a CD - R or CD - RW with files that have been burned on the disc it comes tells me that I have inserted a blank disc. Also does not burn
-
What WLAN drivre I use for Satellite A100-787?
There are several drivers for my computer Satellite A100-787 (PSAAN) for wireless local area network. Some are by Atheros and some by Intel, which is mine? I can't.
-
Sustainability T440s vs carbon X 1?
I'm in the market for a new laptop and I saw the X 1 touted for its reliability, but it looks like the t440s is as well built, spill, etc... Who would be considered the most durable (physical damage and a build-up of heat) of the two? Thank you!