Photosmart C6180 problem of Power-Up/Power-Down - loops on/stop/start/stop etc.

Similar Questions

• OfficeJet 4620 wants to power down, but won't start button / stop

  Most of the time the printer/scanner works fine, but sometimes it "sulking" and wants the power off, but won't the power button.

  I have a switch in the extension cord to the electric line which I use in these moments there (better than pulling the plug?).

  When the current is applied again the printer usually goes back to work.

  Sometimes he blames me for not using the power button - I really try that and generally goes back to work when I promise to do better in the future.

  Yet at other times, he wants the power cut off, even once.

  The printer is connected to the router via wifi.  Two computers are connected by ethernet to the router using Windows XP or Linux (via hplip).  One or more laptops can be connected to the router using Win7 or Linux (via hplip) wifi.

  (Really) thanks for your help and suggestions, but I think I've reached my limits.  I followed your link and entered the information produced.  The result is that the warranty expired 11 days ago.  It's an interesting period of guarantee; ten days of 27 months.  I bought September 15, nearly 11 months ago.

• Power problem: Photosmart C6180

  My printer Photosmart C6180 continually lights stays on for about 30 seconds and then seems to lose power.

  I tried the troubleshooting steps already using different points of sale and unplug power for a period of time, but nothing has solved this problem.

  Someone know if it sounds like a problem with the printer or is there something wrong with the power supply?

  The printer was working fine a few days ago, nothing happened that may have caused damage that I know.

  Thanks for any help you can offer!

  Sorry, I should have searched the forum more carefully before posting, I found the solution to my problem.

• Sprocket: My gear don't power down and can not pair on my mobile device. How to solve this problem?

  Hey everybody,

  My pinion don't power down and can not pair on my mobile device.  How to solve this problem?

  Thank you

  Bill

  Hi Bill,

  This should solve your problem!

  1. Locate the reset button near the port of loading.

  

  2. Insert gently a needle into the reset button access point and press the reset for 3 seconds button.  Resetting the printer and everything already illuminated turn off the LED.

  3. turn on the printer by pressing the power button until the white LED lights

• How to solve the problems of windows 10 shut down (power, lighting the keyboard is always on)?

  Nice day

  How to solve the problems of windows 10 shut down (power, lighting the keyboard is always on)?

  with regard to my question above. I need to hold the button of power for 5 seconds to completely shut down my laptop. even restart or sleep does not work well. I upgraded a real victory 8.1 to 10 free victory by that windows app reservation offered. IM using acer aspire v5 - 573 g i7, version gt750m, Finnish keyboard

  solutions, I tried to random searches that did not work for me.
  1 unchecking quick stop to power options
  2 disabling hibernation in cmd (types a code forgot what I have)
  3. update all drivers and bios with sites acer official drivers, driver pack solution 15.8 and utility driver update intels
  4 decommissioning intel management engine components driver 11 to 9.5
  5. go to the bios and reset to the default settings
  6 make a shortcut of "shutdown" with codes e.g. shutdown /s /t 0
  7. click Update stop

  IM thinking of reinstalling windows 10 via recovery which removes applications, files, drivers, etc. and hope this solves. I can't roll back to win 8.1 because ive done this reset before you completely clean out my system of win random 8 and trashes the restore option was gone.

  Thanks in advance

  Hello/Hallo wuschel93,

  exactly what I had. Stop number appears only after a certain time the laptop running.

  The problem is INTEL MANAGEMENT ENGINE RELATED V.11!

  I fixed it with uninstall Intel Management Engine Version 11. Windows will then install version 9.5 automatically. After that I turned off the automatic update of the driver for this device. You can also install 9.5 without uninstalling the old one, it wil crushed.

  Other manufactures also have this problem, but while Acer is still asleep, they provide a solution (including download links):

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/sleep-and-shutdown-issues-after...

  Maybe there are any other issues that result in the same problem. But in most cases, it's the answer. The thread Starter maybe forgotten to disable the automatic driver update or made installation of v9.5 evil?

  TEPCO

• Problem with power options

  I always put my energy saver to be able to turn off my PC after 10 minutes.

  Press a key or move the mouse and it restarts.

  Recently he returned to power down then power on its own.

  I tried several times to reset and have even reset by default and does not...

  I have an ASUS and Windows 7 computer and had no problems with either until recently...

  Any suggestions?

  Original title: ENERGY SAVING

  Hello

  Thanks for posting your query on the Microsoft Community.

   
  You did changes to the computer before the show?
   
  I suggest to remove the battery in case of a laptop and plug it in again and then check.
   
  You can run the troubleshooter of power to set your computer's power settings. The resolution of the problems of power check things as settings timeout of your computer, which determines how long the computer waits before turning off the display or enter the mode 'sleep'. These settings can help you save energy and extend the life of your computer's battery
   
  Open the troubleshooter of power
  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter
   
  See also How to use the registry to set preferred power
  Plan of following article and check if it works:
  When you configure power options for the active power plan in Windows Vista or in Windows 7, the changes do not appear in the Power Options item in Control Panel
  http://support.Microsoft.com/kb/935799/en-us

  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  Hope this solves the problem. If the problem persists, you can write back to us and we will be happy to help you more

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• Power down, windows 7 sets the Verr Num led on just before turning off

  I have a Fujitsu 101/102 PS/2 keyboard connected on a 64-bit windows system 7.

  Recently, my motherboard has failed, and I installed a new motherboard, where I had to do some basic recovery for windows 7 to come.
  Because then I find that when I turned off the system, during the eve of the sequence, when I get the screen power off mode, the indicator (Led) NumLock on the keyboard is turned off first, and then just before that the system turns off the Num Lock Led is lit once again and of course remains on until I then use my PC.
  I would like to get a solution to this problem.

  The State of the Num Lock is determined by the BIOS during POST (Power On Self Test). It is not defined by Microsoft during the power down, but the BIOS of your computer can trigger the light briefly during a stop.

  If you enter the BIOS of your computer during the power upward (F4 maybe?), you should be able to find a framework that governs the State of the NumLock at startup. Change this option to what you want and save your output settings.
  The BIOS settings are retained by EPROM chips on your motherboard, which explains why things have changed with a new motherboard.

• Iomega home media hmnd2 becomes inaccessible after a power down

  Hi all

  I have a hmnd2 that I had for years. After that a recent unexpected power down I no longer accesses through my home network. Ping the ip address returns no response. white light on the front is on and I can hear it running, but I have no access. at startup, I hear a form of slight movement of the hard drive, but then it goes quiet. I tried the reset button, but no luck. also tried through the usb at the back. My Network senses there is something out there but can not load a driver (and so it remains inaccessible). I guess that the material is ok, but OS does not or something like that.

  someone at - it ideas? thnx guys.

  Rgds,

  The f

  Hello jeffga,

  You can contact support and request an imager, it can get the NAS running again:
  https://Lenovo-EU-en.custhelp.com/app/answers/detail/A_ID/14722

• IPS-4270-20 power down

  Madam, Sir, friends.

  For unknown reason the IPS Power Down, always at the same time.

  How can I check the temperature of the equipment?

  How can I check the power supply?

  The only thing I've seen different, is the internal system health indicator was red flashing.

  Someone knows how to fix this?

  Concerning

  4270-20 IPS sensor device has a panel integrated diagnostics that you can consult to refine the cause:

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/installation/guide/hw_installing_4270.html#wp40629

• OfficeJet k5400 prints then all the lights light up yellow, power down then turn on printer resets loan

  OfficeJet k5400 prints then all the lights light up yellow, power down then turn on printer resets loan. It's all new HP Officejet pro 8000 to had the power to issue even down to reset.

  Looks like the power module is out. It's the black brick in the power cord. The only way to replace it is to contact HP, but before you do that, try to reset the module. The document following the link will guide you through it. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  The printer will not turn on or respond

  HP Technical Support call case form

• My new S2440L face the problem of power outage

  I have just purchase S2440L to replace my old S2340L. With S2340L, I have never have any problem of power outage but when I plug my new S2440L, it was goes black for a few seconds. The problem was random 10 minutes to 40 minutes. These two monitor was same HDMI cable (and work fine on my SmartTV too), PC same and even graphic card driver. I try to reinstall a fresh driver but still a problem. Is - it could be hardware related? Perhaps S2440L have a hardware problem or a S2440L need a more specific HDMI cable? Now I have any problem with my S2440L. the blackout has been occur when overheating circuit behind the monitor. I was watching about about on the HDMI port of overheating by googling and found that HDMI can fail if the (amplifier HDMI) circuit was overheated (I'm not have overheating issue on my old S2340L (rev.) A00). i sure as S2440L (mine is rev. A01) have material problem on HDMI and circuit surprise (lower part of the monitor) have very high temperatures. I hope you, Dell will be it is your responsibility that your monitor, S2440L have an overheating problem / high temperature and could be a HDMI port blackout curtains. It's bad for me avoid this problem by using the VGA port.

  Thank you, ChozeriZes.

  Christ

  I just touch the border smaller surface compared to the top edge, it is very hot.

  maybe only my S2440L have this problem...

  Today, I remove my VGA card and the power cord, and reinstall the whole again, the problem in black often seem to not like it before summer. It's just a couple of times for that day.

  Actually I feel fine with this monitor, both design and image, but still nervous about high temperature, it's may be the major problem in the long term.

  Maybe I was too early to conclude everything... HDMI is a very sensitive matter, as I said in a previous comment, then I have some tests for my S2440L

  -overclock grid power my VGA card around 2% and delete some fan of my system.

  -find the new place for the power adapter avoid the heat. (I found this use of monitor LG IPS 1. 3a adapter 19V is perhaps)

  Note: I use 750W Seasonic and power supply of 5V and 12V is pretty good (5.1V and 12.05V).

  OK, now I need to close this thread as solved and and report this problem like power supply problem; in major relate.

  "on monitor blackout curtains when use the HDMI port occurs when power on unstable system will also be able to rack in the House, heat and cable must use HDMI1.4 full spec for sure (if HDMI cable does not include with the package).

  Best regards

  ChozeriZes

• I bought my palm tx 3 years ago... problem: the power button work anymore; appear it only in a white light scanning when I press on the back 'home '.

  I've had my palm tx for 3 years now and I have had some problems with it. (because I bought it on the web, there was the guarantee) the first problem is the "power" does not work anymore? and the second, the scan goes blank (white) when I press one funds 4 (calendar or at home...). What could be the case of this defect?

  I bought my palm tx 3 years ago... problem: the power button work anymore; appear it only in a white light scanning when I press on the back 'home '.

  The warranty on a TX is only 1 year from the date of purchase.  Yours is way past the period covered.

  The switch was a small part of the TX.  Pressing any other button will turn on the unit, and it will turn off let it expire.

  There is a wire on the switch repair yourself, if you're a DO-IT-YOURSELF person here type:

  http://Forum.Brighthand.com/showthread.php?t=255871

  Have you tried a Soft Reset?  A warm reboot?  A Hard Reset?    Resets are explained here:

  http://KB.Palm.com and enter 887 'ID of Solution '.

  WyreNut

  Message relates to: Centro (AT & T)

• HP Photosmart C6180: hp photosmart c 6180 turns off when it is connected to the network and blinks green photo

  When my Photosmart C6180 is related to two wireless and ethernet network after any number of hours it stops itself down and the green light on the front panel by the icon of camera flashes.  You will then have to push the power button to turn back.  Not very practical for a network printer. Router is a Linksys WRT 1900 ACS.

  Hi wjabdella,

  Thank you for your answer!

  In the post I provided on the hard reset, he mentioned: sometimes, when plugged into a surge protector or battery backup, the quantity of electricity is not received by the printer.  Power problems can cause printing problems.  It is particularly important to be plugged directly into a wall outlet with wireless connectivity problems, "sleep mode" and other power problems.

  So by unplugging the power and waiting, it resets the printer almost to its original state without making a complete factory reset and lose any other information.

  Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I hope that answers your question!

• HP Photosmart C6180 Magenta Ink not printing

  error message: no

  description of the problem: Magenta Ink not print not EXCEPT on the page that prints after aligning the print cartridge printing is performed. At the bottom of this page, the bars of yellow, Cyan and Magenta print perfectly, just like the mixture of the color shown in the colorful bird printed below the bars.

  Self Test Diagnostic Page is printed with bars No. Light Magenta or Magenta, under print quality model. State of ink and level for both shows like OK magenta and 100%

  Troubleshooting: I ran repeated cycles of head cleaning and aligning the print cartridge print without changing the output. The page that prints after cleaning has NO magenta bars or lines. Seems the page that prints after alignment. Via e-mail support, I was directed to perform a complete reset "semi" and "the NVM reset" - neither of these had no effect. Magenta inks have been replaced, but the problem persists.

  Exchange: the printer had not been used for several months.

  My printer started working. It had been disconnected and sitting for several months. I turned it to try the HP solutions (below) and found that it worked - I had nothing to do!  In any case, I hope this can help some of you with similar problems:

  Hello
  
  Thank you for contacting HP Total Care.
  
  I'm Vivian of HP Total care for all-in-One products, and this response is in what regards the problem with HP Photosmart C6180 all-in-One Printer.
  
  Of your mail, I understand you have a HP Photosmart C6180 all-in-One Printer. Currently, you have a problem in which the printer prints in magenta only on the alignment page and not even on the test page.
  
  I am aware of the importance of the issue and will give you the appropriate information. I need your cooperation and appreciate your efforts to resolve the issue.
  
  First of all I want to thank you for the link, I'll take that as a feedback and will forward it to the concerned Department. However it is not a known, issue because in this case, HP will take immediate action and make sure that defective cartridges do not reach the market.
  
  Please try the following troubleshooting steps. I assure you that those measures would solve the problem.
  
  I ask you to check if you have the same problem with the copy as function. If the printer copy very well magenta do not perform one of the steps given and please get back to us for further assistance. However if you encounter the same problem with the copy as well please continue with the provided steps.
  
  First step: clean the copper contacts.
  
  (1) take a lint cloth or a cotton ball, it wet with water.
  (2) clean the cartridge copper contacts.
  (3) you have the same type of copper on the printer also, contacts if you are able to reach their own contacts in copper on the printer also.
  (4) reinstall the cartridge in its housing.
  (5) when the printer is on, unplug the power cord from the printer.
  (6) press and hold the power button for about 30 seconds.
  (7) re plug the power cord into the printer and the printer.
  
  If the problem persists, proceed to the next step.
  
  Step 2: Perform a drain of power on the printer.
  
  (1) remove the power cord from the product
  (2) press and hold the power button for about a minute (while the power cord is not connected to the printer).
  (3) release the button.
  (4) connect the power cord to the product
  (5) use the button to turn the product on.
  
  Connect the printer to the computer and check; If the problem persists, proceed to the next step.
  
  Step 3: Reset the printer to the factory settings.
  
  (1) use the button to turn the product on.
  (2) remove the power cord from the product
  (3) press and hold the # and 6 buttons.
  (4) while now buttons, plug the power cord to the product
  (5) to continue to press the buttons for about 30 seconds.
  (6) use the button to turn the product on.
  (7) if these steps do not resolve the problem, it will be a hardware problem with the printer in this case I suggest you take the printer to the nearest authorized Service Provider for the service.
  
  Please follow these steps and get back to us with the results, if you need more help, please reply to this message and we will be happy to help you further.
  
  We look forward to hear from you.
  
  For more information on keep your HP and Compaq products up and running, please visit our Web site at:
  
  http://www.HP.com/go/TotalCare

  ALSO:

  If the printer performs the color copy and you get magenta on the copy, it is obvious that the printer works fine, it's a software problem. I ask you to try the following steps, depending on your convenience and get back to us with the results.
  
  First step: reset the printing system
  
  To use the reset printing system feature, follow these steps:
  
  1. in the Finder, choose utilities from the menu reach.
  2. open the printer setup utility.
  3. in the printer setup utility menu, choose Reset Printing System.
  4. click on reset.
  
  Second step: check/repair disk permissions
  
  Click on Go tab in the top menu bar.
  Select the utilities tab.
  Click disk utility.
  Once disk utility appears, select the drive and click the check permissions.
  
  This can take a long time to complete as the Mac will try to check all permissions to the hard drive.
  Now click on the tab authorization to repair disc.
  
  This can take a long time to complete as the Mac will try to repair all permissions to the hard drive.
  Once Permission to disk check is complete, restart the Mac
  
  Step 3: Add the printer again
  
  1. click the Apple on the top of the left hand button.
  2. click on Preferences system, window system preferences will open.
  3. click on the printers and faxes icon.
  4. click on add the symbol on the bottom of the left hand.
  5. you see your printer in the list, select it and click Add on the right side.
  
  Please, do the following and get home with the results, for further assistance please get back to us, we will be happy to help you.
  For more information on keep your HP and Compaq products up and running, please visit our Web site
  to:
  http://www.HP.com/go/TotalCare